营养素与亚临床铅中毒的防治

营养素能有效防治亚临床铅中毒,阐述了钙、铁、锌、硒及维生素等营养素与铅毒性作用的相互关系。     

微波消解–石墨炉原子吸收法测定化妆品中的铅

建立了微波消解–石墨炉原子吸收光谱法测定化妆品中铅的方法。探讨了样品前处理条件、基体改性剂的选择和优化、石墨炉升温条件等对测定结果的影响。在优化的试验条件下,铅的质量浓度在0~100 ng/mL范围内与吸光度具有良好的线性关系,线性相关系数r=0.9991,检出限为0.33 ng/mL。用该法对5种化妆品中的铅进行测定,加标回收率在95.0%~106.1%之间,测定结果的相对标准偏差不大于3.6%。该方法可应用于化妆品中痕量铅的分析。     

应用多接收器电感耦合等离子体质谱法测定海洋碳酸盐中稳定铅同位素组成

研究了多接收器电感耦合等离子体质谱仪(MC-ICP MS)测定铅同位素比值时,影响测试结果准确度和精密度的主要因素及其优化过程。在优化条件下,10 h内连续30次测定4 ng/mL NIST SRM 981同位素标准溶液铅同位素比值,获得208Pb/206Pb、207Pb/206Pb和206Pb/204Pb相对标准偏差(RSDs)分别为0.005%、0.004%和0.054%。长期监测208Pb/206Pb、207Pb/206Pb和206Pb/204Pb,标准偏差(2SDs)分别为0.000 06、0.000 05和0.006 7。采用NEPTUNE MC-ICP MS法测定了低铅海洋碳酸盐样品中稳定铅的同位素比值,并对南海橙黄滨珊瑚(Porites lutea)和库氏砗磲(Tridacna gigas)进行了分析,得到全流程空白为8～10 pg,重复样误差优于0.1%。经0.50 mol/L HNO3洗脱之后,得到海南珊瑚样品中208Pb/206Pb、207Pb/206Pb的比值分别为2.086 2±0.001 5、0.849 90±0.001 47(n=16);海南砗磲样品中208Pb/206Pb、207Pb/206Pb的比值分别为2.116 9±0.004 2、0.864 81±0.001 62(n=9)。进一步考察了南海海洋碳酸盐中204Pb的同位素比值。分析结果表明,南海海洋碳酸盐中稳定铅同位素比值与中国气溶胶、珠江三角洲大气沉降、黄土及南海海底玄武岩等具有很好的相关性。方法适用于复杂基体高钙低铅的海洋碳酸盐样品中铅同位素比值的分析。     

FEW: A workflow tool for free energy calculations of ligand binding

In the later stages of drug design projects, accurately predicting relative binding affinities of chemically similar compounds to a biomolecular target is of utmost importance for making decisions based on the ranking of such compounds. So far, the extensive application of binding free energy approaches has been hampered by the complex and time‐consuming setup of such calculations. We introduce the free energy workflow (FEW) tool that facilitates setup and execution of binding free energy calculations with the AMBER suite for multiple ligands. FEW allows performing free energy calculations according to the implicit solvent molecular mechanics (MM‐PB(GB)SA), the linear interaction energy, and the thermodynamic integration approaches. We describe the tool's architecture and functionality and demonstrate in a show case study on Factor Xa inhibitors that the time needed for the preparation and analysis of free energy calculations is considerably reduced with FEW compared to a fully manual procedure. © 2013 Wiley Periodicals, Inc.     

醋酸溶液中Pd-CuPc/Y催化甲烷选择氧化制甲醇

以氯化铜、钼酸铵、苯酐、氯化铵、尿素和NaY分子筛为原料,采用苯酐-尿素法制备了酞菁铜/分子筛复合物CuPc/Y.采用等体积浸渍法将金属钯担载在CuPc/Y上制备了Pd-CuPc/Y催化剂,并在醋酸水溶液中考察了其催化甲烷选择氧化合成甲醇反应的性能,结果表明,催化性能与反应温度、溶剂中CH₃COOH与H₂O的混合比例、对苯醌用量、反应时间等因素有关,在0.5%Pd-0.5%CuPc/Y添加量0.5 g、CH₃COOH与H₂O体积比4∶1、对苯醌用量1 000 μmol、反应时间3 h、反应温度150 ℃的条件下,甲醇的最佳生成量为1 840 μmol.Pd-CuPc/Y催化剂可以多次循环使用,但由于催化剂流失和催化剂表面的钯粒子聚集的原因,循环使用后的催化剂催化活性有所下降.Pd-CuPc/Y在醋酸溶液中催化甲烷选择氧化合成甲醇是亲电取代反应和活性氧物种氧化共同作用的结果.     

Syntheses,Structures, Luminescent Properties and Photocatalytic Activities of Two Lead（II） Compounds

Two lead（ll） compounds, [Pb（qlc）（phen）2（NO3）]e-H20 （1） and [Pb（qlc）z（phen）]-3H20 （2） （Hqlc = quinoline-3-carboxylic acid, phen = 1,10-phenanthroline）, were synthesized and charac- terized by elemental analysis, single-crystal X-ray diffraction, IR and thermogravimetric analysis. Crystal 1 is of monoclinic, space group C2/c with a = 25.246（5）, b = 12.543（3）, c = 18.917（4） A, β = 105.77（3）°, V= 5765（2） A3, Z = 4, C68H46N12OllPb2, Mr = 1621.53, Dc = 1.886 g.cm-3,/.t（MoKa） = 5.912 mm-1, F（000） = 3152, GOOF = 1.080, the final R = 0.022 and wR = 0.0571 for 4822 observed reflections （1 〉 2a（/））. Crystal 2 is oftriclinic, space group Pi with a = 8.7883（10）, b = 11.7031 （13）, c = 15.9320（17） A, a = 69.9400（10）, fl = 78.9780（10）, 7 = 79.1650（10）°, V = 1497.4（3） A3, Z = 2, C32H26NaO7Pb, Mr. = 785.71, Dc = 1.729 g.cm-s, p（MoKa） = 5.688 mm-1, F（000） = 756, GOOF = 1.106, the final R = 0.0313 and wR = 0.088 for 59i5 observed reflections （1 〉 2σ（I））. Single-crystal X-ray diffraction analysis reveals that 1 exhibits a two-dimensional （2D） layer based on π-π stacking interactions between phen. Simultaneously, the adjacent 2D layers are assembled via π-π stacking interactions between phen and quinoline tings into a 3D supramolecular structure. The zero- dimensional structure of 2 is also further extended by π-π interactions to form a 2D supramolecular layer. Furthermore, these two compounds exhibit photoluminescence at room temperature in the solid state and their photocatalytic activities have been studied by degradation methylene blue.     

Application of the Combustion Method in a Closed Flask to the Lead Determination in Atmospheric Aerosols

Abstract

The destruction of the filter for metal determination in atmospheric aerosols is an important step in the analysis. Nowadays the decomposition of this kind of sample has not been completely solved, so it is interesting to study new methods for filter sample attack. In the present work the application of the combustion method in a closed flask for mixed cellulose esters filter decomposition for lead determination is proposed. For this purpose optimum operating conditions as stopper flask design, sample size, flask volume, shaking time and volume and concentration of absorbing solution are established, and accuracy and precision of the proposed method using AAS for the measurements is given. The results obtained by the closed flask combustion are compared with those found by wet attack with HNO₃. The method proposed is rapid, has low reagent contamination and no loss of lead by volatilization or by amalgamation occurs. This method shows an accuracy and a precision in good agreement with the standard method.     

The Photodecomposition of 1,l-Dichloro-2,2-bis(5′-chloro-2′-methoxyphenyl)ethylene (MPE), an Analogue of DDE

The solution-phase photodecomposition of l, l-dichloro-2,2-bis(5′-chloro-2′-methoxy-phenyl)ethylene (MPE) has been studied at an excitation wavelength of 313 nm in the presence of O₂ as well as in vacuum-degassed solutions. Only two non-volatile compounds are produced: 2,5-dichloro-3-(5′-chloro-2′-methoxyphenyl)benzofuran (BFD) and a minor product which was not identified. The BFD represents approximately 90% of the total non-volatiles. The volatile products were identified as CH₃Cl, CH₄ and HC1, with CH₃C1 being approximately 99.9 % of the total volatiles. Photolyses were carried out in C₆H₁₂ and CCI₄ solvents, the same products being observed in both solvents. Variation of MPE concentration has little or no effect on the relative quantum yield of decomposition. The photodecomposition of MPE does not follow the same pathway as the photodecomposition of DDE.     

Cloud point extraction for the determination of cadmium and lead employing sequential multi-element flame atomic absorption spectrometry

A cloud point extraction procedure for pre-concentration and determination of cadmium and lead in drinking water using sequential multi-element flame atomic absorption spectrometry is described. 4-(2-thiazolylazo)-orcinol (TAO) has been used as complexing agent and the micellar phase was obtained using the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) and centrifugation. The conditions for reaction and extraction (surfactant concentration, reagent concentration, effect of incubation time, etc) were studied and the analytical characteristics of the method were determined. The method allows the determination of cadmium and lead with quantification limits of 0.30?µg?L^?1 and 2.6?µg?L^?1, respectively. A precision expressed as relative standard deviation (RSD, n?=?10) of 2.3% and 2.6% has been obtained for cadmium concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively, and RSD of 1.3% and 1.7% for lead concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively. The accuracy was confirmed by analysis of a natural water certified reference material. The method has been applied for the determination of cadmium and lead in drinking water samples collected in the cities of Ilhéus and Itabuna, Brazil. Recovery tests have also been performed for some samples, and results varied from 96 to 105% for cadmium and 97 to 106% for lead. The cadmium and lead concentrations found in these samples were always lower than the permissible maximum levels stipulated by World Health Organization and the Brazilian Government.     

Synthesis and characterisation of a silicon oxide film solid-phase extraction system for lead traces determination: an all the way green analytical method

In this work, an all the way green analytical procedure based on a silicon oxide film-solid phase extraction system is proposed for lead traces determination. From the synthesis of a solid phase extraction (SPE) system and throughout the metal preconcentration and determination only aqueous media were employed. Characterisation of the film was carried out by Scanning Electron Microscopy and Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy. Preconcentration conditions, prior to Pb(II) Electrothermal Atomic Absorption Spectrometry (ETAAS) determination, such as adsorption and desorption time, pH and temperature, were optimised. Langmuir, Freundlich and Dubinin-Radushkevich isotherm models were analysed along with the evaluation of adsorption energy and standard free energy (ΔG ⁰). The greatest adsorption was obtained with incubation at pH 7 and 37°C. By using a small volume of 0.5?mol?L^?1 HNO₃ (0.5?mL) lead was desorbed from the silicon oxide film after 2?h incubation, generating low amount of waste. The films showed better adjustment for the Langmuir model (R^{2 ?}=?0.989). The detection limit (3.29σ) for Pb(II) was 0.228?µg?L^?1. The developed procedure is 10-fold more sensitive in comparison to direct ETAAS determination. Recovery values from soft tap-water and soft well-water were above 95%. When hard water was analysed, Pb(II) adsorption was found to be interfered by Mg²⁺ and Ca²⁺. After five preconcentration cycles relative recovery was found not to decay below 90%, indicating that the silicon oxide film could be used for multiple lead determinations.