聚丙烯固相接枝物的结晶行为

用固相接枝法合成了聚丙烯接枝马来酸锌离聚物（ＰＰ－ｇ－ＭＡＺｎ）。利用Ｘ光、ＰＬＭ和ＤＳＣ研究了它的结晶行为。结果表明：ＰＰ－ｇ－ＭＡＺｎ能促进β－型结晶的形成;接枝物形成的球晶尺寸变小,而且球晶不规整;接枝物的起始结晶温度移向高温,结晶速率加快;等温结晶动力学的研究表明接枝物结晶的成核方式不发生改变。     

聚乙二醇在超临界二氧化碳介质中的结晶行为

利用DSC和偏光显微镜研究了聚乙二醇在超临界CO2 中的结晶情况 ,超临界条件下得到的晶粒小而均匀 ,DSC测试还表明超临界CO2 可提高聚乙二醇的熔眯和溶解焓。     

Annealing and Crystallization of Fe40Ni40P14B6 Glassy Alloy. A DSC study

In this paper a DSC study is reported of the behavior of Fe₄₀Ni₄₀P₁₄B₆ alloy produced by rapid quenching. The experimental results show that relaxation phenomena can be studied directly from the DSC curves. From these experiments, the spread of the E _c values in the literature is attributed to differences in the quenching rates and the presence of variable number of quenched-in nuclei. It is also shown that the microstructure (number and size of crystals) of the non-isothermally devitrified metallic alloy changes with the heating rate; this is a consequence of the shift of crystallization temperatures and, therefore, of the change of the ratio of nucleation and crystal growth rates. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal and Chemical Properties of a Glass in the SiO2-CaO-F System for Dental Applications

The crystallization behaviour of a glass in the SiO₂-CaO-F system was analyzed using differential scanning calorimetry (DSC), X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). Three crystalline phases were detected according to ICDD patterns. The first phase formed at 583°C was identified as CaF₂. The morphology was spherulitic with a diameter of approximately 100 nm. The second phase was formed at 664°C. It was identified as calcium fluoride silicate ‘Ca₂SiO₂F₂’ (ICDD 35-0002). SEM investigation showed that the crystals were spherulitic with a diameter smaller than 100 nm. The crystals were precipitated in the volume of the glass and homogeneously distributed. As a third phase, cristobalite crystallized at 895°C. The simultaneous release of calcium and fluorine ions from the vitreous glass in lactate buffer solution at pH 4.0, simulating an acidic oral environment, was investigated using X-ray photoelectron spectroscopy (XPS). The release of calcium and fluorine ions is of special interest for dental applications. The atomic ratios of the components Si, Ca and F at the glass surface after different leaching periods were determined. In order to investigate the leaching process, concentration profiles were measured using ion beam sputtering with Ar⁺ -ions. The dependence of the atomic ratios of Si, Ca and F on the sputter time was determined in order to measure the depth of the leaching layers. Most probably, the release of calcium and fluoride was controlled by a surface layer rich in calcium and flourine ions which dissolved with increasing leaching time. After 2 min leaching, a fluoride-rich surface layer measuring approximately 10 nm was detected. The atomic ratios of Si, Ca and F were different from the bulk composition ratios in a surface reaction layer of 800 nm thickness. After 30 min leaching time, a calcium- and fluoride-rich surface layer approximately 50 nm thick was formed. The bulk composition was reached at a depth of approximately 500 nm. The main component in the surface layer, after 12 days leaching in acidic environment, was silicon. This revised version was published online in August 2006 with corrections to the Cover Date.     

Crystallization and Melting of Model Polyethylenes with Different Chain Structures

The crystallization and melting of three model polyethylenes of different chain structures have been studied. The polymers studied were a linear copolymer, hydrogenated poly(butadiene); a hydrogenated poly(butadiene)-atactic poly(propylene) diblock copolymer; and a three-arm star hydrogenated poly(butadiene). An important feature of this work was that the crystallizing portions of the copolymers all have the same molecular lengths.It was found that the overall crystallization rate decreases steadily from a linear to a diblock to the star copolymer. The differences in crystallization rates are related primarily to the activation energy for segmental transport. The non-crystallizable structure affects the segmental mobility to different degrees. An estimation of this effect is presented from the analysis of the overall crystallization rates using classical nucleation theory. In spite of thedifferences in their molecular structure, there are no major differences in the supermolecular structure of samples crystallized rapidly or slowly cooled.The melting process followed by DSC of the isothermally crystallized linear and star copolymers shows two endothermic peaks at intermediate undercoolings. The double melting is associated with a partitioning of crystallizable ethylene sequences during crystallization. The longest sequences are preferentially selected in the early stages of the crystallization. Single melting peaks are obtained for high and very low undercoolings for the linear and the star copolymers as well as for the diblock in the whole range of temperatures. The lack of the second, lower melting endotherm in the diblock could be associated with the influence in the crystallization process of the amorphous block in the microphase segregated melt.This revised version was published online in November 2005 with corrections to the Cover Date.     

聚甲醛/蒙脱土纳米复合材料非等温结晶动力学研究

聚甲醛/蒙脱土纳米复合材料非等温结晶动力学研究     

PET/LCP反应性共混物的非等温结晶动力学

采用DSC方法研究了聚对苯二甲酸乙二酯 (PET)和热致性液晶共聚酯 6 0PHB PET (LCP)体系在少量扩链剂双 (2 唑啉 ) (BOZ)存在下形成的反应性共混物的非等温结晶动力学 .结果表明反应性共混物的Avrami指数均在 3 0～ 4 5之间 ,BOZ的加入使反应共混物中PET组分的结晶速率降低 ;表明BOZ对酯交换的促进作用 ,使所生成的共聚酯中PET嵌段的数均序列长度变短 ,而使结晶在某种程度上较为困难 ,但对体系的成核和结晶生长机理无明显影响 .结果还表明 ,随冷却速率的增大结晶峰向低温方向移动     

聚丙烯/蒙脱土纳米复合材料非等温结晶动力学的研究

用熔融插层法制备聚丙烯 蒙脱土纳米复合材料 ,用DSC手段研究了其非等温结晶行为 ,并与聚丙烯进行了对比 .对所得数据分别用修正Avrami方程的Jeziorny法、Ozawa法和Mo法进行处理 .结果表明 ,用Jeziorny法和Mo法处理非等温结晶过程比较理想 ,而用Ozawa法处理则不太适用 .用Jeziorny法求出的参数Zc和n随冷却速率的增加而增加 ,但复合材料的Zc 和n略大于聚丙烯的Zc 和n ,用Mo法求出的参数F(T)随结晶度的增加而略有增加 ,a几乎未变 ,复合材料的F(T)略小于聚丙烯的F(T) ,复合材料的a约为 1.40略大于聚丙烯的a(其值约为 1.0 4) .按Kissinger方法计算出聚丙烯及聚丙烯 蒙脱土纳米复合材料的结晶活化能分别为 189.37kJ mol,15 5 .6 9kJ mol,说明有机蒙脱土的加入 ,降低了聚丙烯的结晶活化能 ,起到了异相成核的作用     

Work of Fracture and Strain-induced Cold Crystallization Behavior of Amorphous Copolyester Sheets

The toughness of amorphous copolyester sheets was assessed by the essential work of fracture (EWF) concept. While the yielding-related work of fracture terms did not change significantly, the necking-related parameters strongly decreased with decreasing entanglement density of the copolyesters having different amounts of cyclohexylenedimethylene (CHDM) units in their backbones. Furthermore, copolyesters with high CHDM content and thus less entanglement density showed full recovery of the necked region beyond the glass transition temperature, i.e. the ‘plastic’ zone in the related specimens formed by cold drawing and not by true plastic deformation. By contrast, the copolyester with negligible amount of CHDM did not show this shape recovery. Modulated differential scanning calorimetry (MDSC) revealed that the necking in the latter system was accompanied by strain-induced crystallization. The superior work hardening in the necking stage of the respective poly(ethylene terephthalate) (PET) specimens can thus be ascribed to stretching of the entanglement network with superimposed crystallization. This revised version was published online in August 2006 with corrections to the Cover Date.     

Preparation of γ-Alumina Membranes From Sulphuric Electrolyte Anodic Alumina and Its Transition to α-Alumina

Gamma-alumina membrane was prepared from anodic (amorphous) alumina (AA) obtained in a sulphuric acid electrolyte. The transformation scheme, i.e., the crystallization to form metastable alumina polymorphs and the final transition to α-Al₂O₃ with heating was studied by TG-DTA and X-ray diffraction (XRD) using fixed time (FT) method. When heating at a constant rate, the crystallization occurred at 900°C or higher and the final formation of α-Al₂O₃ occurred at 1250°C or higher, which temperatures were higher than the case of using anodic (amorphous) alumina prepared from oxalic acid electrolyte. Relative content of S of the products was obtained by transmission electron microscope (TEM)-energy dispersive spectroscopy (EDS). The proposed thermal change of anodic alumina membrane prepared from sulphuric acid is as follows: 1. At temperatures lower than ca 910°C: Formation of a quasi-crystalline phase or a polycrystalline phase (γ-, δ- and θ-Al₂O₃); 2. 910–960°C: Progressive crystallization by the migration of S toward the surface within the amorphous or the quasi-crystalline phase, forming S-rich region near the surface; 3. 960°C: Change of membrane morphology and the quasi-crystalline phase due to the rapid discharge of gaseous SO₂; 4. 960–1240°C: Crystallization of γ-Al₂O₃ accompanying δ-Al₂O₃; and 5. 1240°C: Transition from γ-Al₂O₃ (+tr. δ-Al₂O₃) into the stable α-Al₂O₃. The amorphization which occurs by the exothermic and the subsequent endothermic reaction suggests the incorporation of SO₃ groups in the quasi-crystalline structure. This revised version was published online in July 2006 with corrections to the Cover Date.