Output dynamics and stabilisation of a multi-mode double-clad Yb-doped silica fibre laser

The intensity dynamics of the double-clad Yb fibre laser have been characterised. Stabilisation of the fibre laser intensity by using uniform bi-directional pumping is demonstrated. For the single-end-pumped Yb fibre laser, the output becomes more stable for the shorter fibre length due to the higher threshold of stimulated Brillouin scattering, SBS, and Kerr effects and the reduction of saturated absorber effects caused by any unpumped fibre section. By additional pumping in a double-end-pumped configuration, the output power can be scaled higher before detecting high intensity pulses initiated by SBS in the Yb fibre laser due to the reduction of saturable absorption effect. It is confirmed that uniform pumping enhances the stability of the laser output.     

Operational characteristics and power scaling of a transverse flow transversely excited CW CO<Subscript>2</Subscript> laser

Transverse flow transversely excited (TFTE) CO₂ lasers are easily scalable to multikilowatt level. The laser power can be scaled up by increasing the volumetric gas flow and discharge volume. It was observed in a TFTE CW CO₂ laser having single row of pins as an anode and tubular cathode that the laser power was not increasing when the discharge volume and the gas volumetric flow were increased by increasing the electrode separation keeping the gas flow velocity constant. The discharge voltage too remained almost constant with the change of electrode separation at the same gas flow velocity. This necessitated revision of the scaling laws for designing this type of high power CO₂ laser. Experimental results of laser performance for different electrode separations are discussed and the modifications in the scaling laws are presented.     

Depth profiling of latex blends of fluorinated and fluorine‐free acrylates with laser‐induced secondary mass spectrometry

We explored phase separation and self‐assembly of perfluoroalkyl segments at the surface of polymer films obtained from latices of semifluorinated acrylate copolymers and the corresponding latex blends of nonfluorinated and semifluorinated polyacrylates. With laser‐induced secondary mass spectrometry the fluorine distribution was measured after annealing above the minimum film‐forming temperature of the polymers up to a depth of several micrometers. Depth profiles of a semifluorinated acrylate homopolymer and latex blends thereof with fluorine‐free alkylacrylates with 25, 50, and 75 mol % semifluorinated acrylate as well as a copolymer comprised of alkyl acrylate and semifluorinated acrylate (50/50 mol %) were investigated. In the case of latex blends containing both semifluorinated polyacrylates and fluorine‐free or low‐fluorine polymers, self‐assembly accounted for enrichment of the perfluoroalkyl segments at the surface. Coatings exhibiting low surface energy and having a substantially reduced total fluorine content were obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 360–367, 2003     

Characteristics of Ti0.97Co0.03O2:Sb0.01 dilute magnetic semiconducting thin films deposited at 500 °C by pulsed laser deposition

Epitaxial Ti_0.97Co_0.03O₂:Sb_0.01(TCO:Sb) films were deposited on R-Al₂O₃ (1 1 0 2) substrates at 500 °C in various deposition pressures by pulsed laser deposition. The solubility of cobalt within the films increases with decreasing deposition pressure at a deposition temperature of 500 °C. The TCO:Sb films deposited at 5×10⁻⁶ Torr exhibit a p-type anomalous Hall effect having a hole concentration of 6.1×10²²/cm³ at 300 K. On the other hand, films deposited at 4×10⁻⁴ Torr exhibits an n-type anomalous Hall effect having an electron concentration of about 1.1×10²¹/cm³. p- or n-type DMS characteristics depends on the change of the structure of TCO:Sb films and the solubility of Co is possible by controlling the deposition pressure.     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

微量低电离电位的添加物对XeCl准分子激光输出的影响

本文报道在XeCl准分子激光器中添加微量的氯苯(C_6H_5Cl)或四氯化碳(CCl_4),使激光输出能量提高约16％。     

Beam Combination using Stimulated Brillouin Scattering for the Ultimate High Power-Energy Laser System Operating at High Repetition Rate over 10 Hz for Laser Fusion Driver

After the laser was invented in 1960, a phase conjugation mirror has been respected to be the most fantastic one for the laser resonator composition because it can compensate any distortions of the laser beams occurred by the many inhomogenuities of the laser media and optical components. Among the many phase conjugation configurations, the stimulated Brillouin scattering phase conjugation mirror is the most simple one and many researchers have tried to utilize it to develop high power/energy laser systems. For realizing a high energy/power laser system the thermal problem is the most difficult to solve, and some researchers suggested a beam combination technique to reduce the thermal load of the big laser media to many small sized ones. To accomplish the beam combination using stimulated Brillouin scattering phase conjugation mirrors (SBS-PCMs), it is necessary to lock/control the phases of the SBS-PCMs. And some researchers have developed several ways for it, but they can lock the phases of a limited number of beams overlapped at the foci less than 5, or lock the phases by back-seeding technique but it loses the phase conjugation characteristics. For realization of the laser fusion driver, it is necessary to combine more than 10 or 100 beams. And the authors have developed recently a new phase controlling/locking technique which is isolated and independent totally from other beams and it can be applied to an unlimited number of beams in principle.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Spatiotemporal and Thermal Analysis of VCSEL for Short-range Gigabit Optical Links

High-speed Optoelectronic Modules using Vertical Cavity Surface Emitting Lasers (VCSEL) coupled to Multi Mode Fibers (MMF) are a performing and low-cost solution for 10 Gigabit Ethernet (10 GbE) in short-distance optical links. A complete model of the spatiotemporal behavior of multimode VCSELs, through static and dynamic response, noise, thermal effects, and its coupling to MMF has been investigated. Relative Intensity Noise shows modal dependence and can be affected by spatial filtering due to coupling and fiber propagation. Simulations permit to evaluate critical parameters, such as modulation formats, launching conditions, and operating temperature for global bandwidth and eye diagram optimization up to 10 Gb/s. Simulation results are compared to measurements on prototype optoelectronic modules.     

Pulsed pump: Thermal effects in solid state lasers under super-Gaussian pulses

Solid state laser (SSL) powers can be realistically scaled when pumped by a real, efficient and multimode pulse. In this work, a fourth-order super-Gaussian pulse was assumed as a pump for SSL’s and a complete analytical expression for the thermal phase shift is given. Moreover, the focal length of thermal lens in paraxial ray approximation regime was studied. The results when applied to a Ti: sapphire crystal show an appreciable correction for abberation compared to a top-hat pulse.