Review of Fluorescence Spectroscopy in Environmental Quality Applications

Fluorescence spectroscopy is an optical spectroscopic method that has been applied for the assessment of environmental quality extensively during the last 20 years. Most of the earlier works have used conventional light sources in spectrofluorometers to assess quality. Many recent works have used laser sources of light for the same purpose. The improvement of the energy sources and of the higher resolution spectrometers has led to a tremendous increase in applications. The motivation for the present review study is the increasing use of laser sources in environmental applications. The review is divided in two parts. The fundamental principles of fluorescence spectroscopy are described in the first part. The environmental applications are described in the second part.     

Dielectric Properties Investigation of Metal–Insulator–Metal (MIM) Capacitors

This study presents the construction and dielectric properties investigation of atomic-layer-deposition Al₂O₃/TiO₂/HfO₂ dielectric-film-based metal–insulator–metal (MIM) capacitors. The influence of the dielectric layer material and thickness on the performance of MIM capacitors are also systematically investigated. The morphology and surface roughness of dielectric films for different materials and thicknesses are analyzed via atomic force microscopy (AFM). Among them, the 25 nm Al₂O₃-based dielectric capacitor exhibits superior comprehensive electrical performance, including a high capacitance density of 7.89 fF·µm⁻², desirable breakdown voltage and leakage current of about 12 V and 1.4 × 10⁻¹⁰ A·cm⁻², and quadratic voltage coefficient of 303.6 ppm·V⁻². Simultaneously, the fabricated capacitor indicates desirable stability in terms of frequency and bias voltage (at 1 MHz), with the corresponding slight capacitance density variation of about 0.52 fF·µm⁻² and 0.25 fF·µm⁻². Furthermore, the mechanism of the variation in capacitance density and leakage current might be attributed to the Poole–Frenkel emission and charge-trapping effect of the high-k materials. All these results indicate potential applications in integrated passive devices.     

一种蓝色聚合物激光材料

聚合物作为一种有机发光材料,由于在平板显示和光电子器件中的良好应用前景而受到广泛研究［１～２］．近年来,一个重要进展是在聚合物中观测到了受激发射（简称Ｐｏｌｙ－ｍｅｒ激光）现象［３～６］．Ｐｏｌｙｍｅｒ激光最早是在溶液中实现的［３～４］．作为一种新型...     

扫描环形光斑激光束优化研究

激光束的形状和能量分布限定了激光的应用范围,为满足不同的激光加工需要,必须对激光束进行变换。针对实验室用CO2激光器在热处理方面的应用,提出了激光扫描环形光斑光束优化法。基于温度场叠加原理建立了扫描环形光斑温度场的数学模型,模拟其温度场,可得到其温度分布特性;通过实验研究,分析了聚焦光斑与扫描环形光斑在激光淬火中对材料的热作用效果。结果表明,扫描环形光斑能改善激光热处理硬化层分布。理论和实验研究表明,激光扫描环形光斑技术可以实现激光热处理光束的优化,有一定的应用前景。     

激光激发水中产生超声波的实验研究

采用压电陶瓷水听器研究了Nd：YAG脉冲激光激发水中产生瞬态超声波的特性,给出了声压信号随距离的变化关系。研究结果表明：用激光产生水下声波是完全可行的。当观测点与光击穿区的距离r远大于柱体长度时,垂直于光传播方向的激光瞬态超声波幅值与r成反比;当观测点与光击穿区的距离r很小时,垂直于光传播方向的声压幅值与产成反比。此外,当激光入射角度发生变化,超声脉冲的幅值也随之发生变化,其幅值在激光束垂直入射的时候最大。     

连续激光辐照ZnSe/MgF2/K9滤光片的透射特性研究

分析了连续激光辐照ZnSe/MgF2/K9滤光片引起透射特性的变化。在室温条件下,用波长0.632 8μm激光作为探测光束,测量了1.06μm连续激光辐照ZnSe/MgF2/K9滤光片温升引起薄膜折射率的改变,导致探测光束通过干涉滤光片后透过率的热致非线性变化。在光斑直径0.75mm条件下,测量了不同功率激光辐照ZnSe/MgF2/K9滤光片引起温升随时间的变化。在激光功率30W,辐照时间2.52s条件下,实验观测到ZnSe/MgF2/K9滤光片薄膜破坏温度约为90℃,辐照时间10s时干涉滤光片形成的薄膜龟裂形貌。     

激光辐照PC型HgCdTe探测器的实验研究

分别用连续波1.319μm激光和10.6μm激光辐照PC型HgCdTe红外探测器时,得到了不同辐照光功率密度下,探测器输出的一系列实验结果。给出了在波长为1.319μm的波段内激光辐照下PC型HgCdTe探测器的饱和阈值;用波长为10.6μm的波段外CO2激光辐照探测器时,发现了一些与波段内激光辐照探测器时大不相同的实验现象;对实验结果进行了分析。简要总结了PC型HgCdTe探测器对于波段内和波段外激光辐照的响应机制。     

激光触发多级多通道开关研究

研究了200kV激光触发多级多通道开关的运行机理,该开关在直流电压下以四倍频Nd:YAG激光器为触发源进行的实验结果表明：开关触发延迟时间及其抖动随开关电压、激光能量和充气压力上升呈指数下降趋势,对混合气体则随气体密度上升而上升。随透镜焦距的增大延迟时间及其抖动呈上升趋势。该开关实现了多通道放电。     

利用“神光-Ⅱ”激光装置多路光束叠加直接驱动下的冲击波平面性及稳定性

利用“神光-Ⅱ”的3路基频光输出及小透镜列阵束匀滑技术,通过优化设计和合理地选择光路组合,实现了多路叠加斜入射的驱动激光, 在靶材料中产生一个650~750μm范围内平面性良好的冲击波,有效地提高了“神光-Ⅱ”输出光束的利用率。同时,利用斜面靶进行的冲击稳定性实验表明,在靶面功率密度分别为3.26×1014及2.56×1014W/cm2时,冲击波至少在28.38~55.82和22.13~35.07μm的Al样品厚度内是稳定传播的。     

DF/HF化学激光器HYLTE喷管的副喷管质量流量系数

对DF/HF化学激光器HYLTE喷管的副喷管质量流量进行了数值和理论计算,得出入口滞止压力在0.01~0.4MPa之间、喉道半高度在0.1~0.9mm之间的喷管的氘气,氢气和氦气质量流量系数,总结出质量流量系数随入口滞止压力和喉道高度的变化规律,并给出拟合公式,为副喷管的设计提供依据。