高精度的光纤衰减系数测试系统的设计

利用常规仪器设备，设计了一套集光、机、电为一体的光纤衰减测量,实现了数字化监测显示，并可与微机接口；采用双光路法，消除了由于光源光强不稳定产生的误差。     

Ion implantation induced by Cu ablation at high laser fluence

High energy laser plasma-produced Cu ions have been implanted in silicon substrates placed at different distances and angles with respect to the normal to the surface of the ablated target. The implanted samples have been produced using the iodine high power Prague Asterix Laser System (PALS) using 438 nm wavelength irradiating in vacuum a Cu target. The high laser pulse energy (up to 230 J) and the short pulse duration (400 ps) produced a non-equilibrium plasma expanding mainly along the normal to the Cu target surface. Time-of-flight (TOF) technique was employed, through an electrostatic ion energy analyzer (IEA) placed along the target normal, in order to measure the ion energy, the ion charge state, the energy distribution and the charge state distribution. Ions had a Boltzmann energy distributions with an energy increasing with the charge state. At a laser fluence of the order of 6 × 10⁶ J/cm², the maximum ion energy was about 600 keV and the maximum charge state was about 27+.In order to investigate the implantation processes, Cu depth profiles have been performed with Rutherford backscattering spectrometry (RBS) of 1.5 MeV helium ions, Auger electron spectroscopy (AES) with 3 keV electron beam and 1 keV Ar sputtering ions in combination with scanning electron microscopy (SEM). Surface analysis results indicate that Cu ions are implanted within the first surface layers and that the ion penetration ranges are in agreement with the ion energy measured with IEA analysis.     

Pulsed laser deposition of nanostructured Ag films

Ultra-thin (0.5-5 nm) films of Ag have been prepared by pulsed laser deposition in vacuum using a 26 ns KrF excimer laser at 1 J cm⁻². The deposition was controlled using a Langmuir ion probe and a quartz crystal thickness monitor. Transmission electron microscopy showed that the films are not continuous, but are structured on nanometer size scales. Optical absorption spectra showed the expected surface plasmon resonance feature, which shifted to longer wavelength and increased in strength as the equivalent film thickness was increased. It is shown that Maxwell Garnett effective medium theory can be used to calculate the main features of optical absorption spectra.     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

饲喂频率对鲈鱼生长及体生化成分的影响

选取同一种饵料设置1次·d-1、2次·d-1、3次·d-1、4次·d-14个饲喂频率,采用静水连续充气养殖系统,在盐度为26.0%～27.0%、温度为26～30℃条件下对鲈鱼(85.95±2.04)g进行为期40d的生长实验.结果表明:(1)饲喂频率影响鲈鱼的生长是由食物转化率和摄食率的提高共同引起的.(2)水分含量随饲喂频率的增高而保持不变;蛋白质含量随饲喂频率的增加,基本保持不变;脂肪含量随饲喂频率的增高而明显减少;灰分含量随饲喂频率的增多而明显增加.(3)鲈鱼的适宜饲喂频率为2次·d-1.     

基于傅立叶变换轮廓术的物面相位提取

采用傅立叶变换轮廓术,针对基频提取的关键技术采用逐行傅立叶变换,准确提取基频信息的方法恢复相位信息.在此基础上,以未畸变条纹为基准,得出被测物体的真实位相值.该方法只需一幅条纹图,节约了测量时间.实验证明可实现无接触面型的自动传感.     

激光准直仪的设计性物理实验

介绍了激光准直仪的结构、工作原理及其在设计性物理实验中的应用     

High power diode single-end-pumped Nd:YVO4 laser

A fiber-coupled diode-single-end-pumped Nd:YVO₄ laser with an Nd:YVO₄ crystal of 0.3 at% doping concentration and 3×3×10 mm³ dimensions was reported. 14.850 W of continuous-wave output power in an M² factor of 1.12 was obtained under pump power of 27.365 W, with an optical conversion efficiency of 60.49%, and a slope efficiency of 64.5%.     

Laser spectroscopic investigation of a new precursor-type polyparaphenylenevinylene

Optical, structural and morphological properties of thin films of polyparaphenylenevinylene (PPV) formed by an alkyl sulfinyl precursor route have been studied. Thin films were fabricated on an optical glass and on quartz glass either by spin-coating of the precursor solution or by layer-by-layer deposition using Langmuir–Blodgett technique. PPV precursor films were also spin-coated on gold-coated glass in order to study thin-film optical parameters by surface plasmon spectroscopy. We have been successful in forming about 40 precursor mono layers on quartz glass by Langmuir–Blodgett technique using optimized surface pressure and dipping conditions. After thermal conversion of the precursor layers good quality fluorescent PPV films of yellow colour have been obtained. Optical characterization of the films was carried out by linear absorption and emission spectroscopy, ellipsometry, and surface plasmon spectroscopy. Structural and morphological studies on the thin films were carried out by using X-ray scattering and atomic force microscopy. Wave-guided travelling-wave laser action has been achieved in a PPV film on quartz glass. The sample was transversally pumped with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). Laser emission occurred at 550 nm for pump pulse energy densities above .     

The effect of construction material, contents and room geometry on the sound field in dwellings at low frequencies

An experimentally validated finite element method is used to model the sound level in rooms at low frequencies. It is demonstrated that the dimensions of rectangular rooms strongly influence the sound pressure level difference. Additional factors were investigated which are not normally considered in the frequency range where diffuse sound field conditions can be assumed. Three effects were investigated: room damping due to wall vibrations, furniture, the effect of small deviations from simple rectangular shapes. It is confirmed by field measurements that the vibrations of masonry walls and floors introduce less damping than surfaces of lightweight construction. Assigning to the FE model a damping equivalent to a surface absorption of 0.02 reproduces the effect of walls of heavyweight construction. Damping equivalent to a surface absorption of 0.15 reproduces the effects of plastered timber-frame walls, floors and ceilings. The work was briefly extended to a room pair built with heavyweight and lightweight material of construction. The modification of the shape of the room frequency response highlights well the effect of material of construction. In-situ and laboratory measurements show that furniture has little effect on steady-state room response below 100 Hz. Modelling a wall recess smaller than 0.5 m improved the agreement between prediction and measurements but the assumption of a simple rectangular room remains appropriate.