Characterization of ZnO-SnO2 thin film composites prepared by pulsed laser deposition

Thin films of ZnO-SnO₂ composites have been deposited on Si(1 0 0) and glass substrates at 500 °C by pulsed laser ablation using different composite targets with ZnO amount varying between 1 and 50 wt%. The effect of increasing ZnO-content on electrical, optical and structural properties of the ZnO-SnO₂ films has been investigated. X-ray diffraction analysis indicates that the as-deposited ZnO-SnO₂ films can be both crystalline (for ZnO <1 wt%) and amorphous (for ZnO ≥ 10 wt%) in nature. Atomic force microscopy studies of the as-prepared composite films indicate that the surfaces are fairly smooth with rms roughness varying between 3.07 and 2.04 nm. The average optical transmittance of the as-deposited films in the visible range (400-800 nm), decreases from 90% to 72% for increasing ZnO concentration in the film. The band gap energy (E_g) seems to depend on the amount of ZnO addition, with the maximum obtained at 1 wt% ZnO. Assuming that the interband electron transition is direct, the optical band gap has been found to be in the range 3.24-3.69 eV for as-deposited composite films. The lowest electrical resistivity of 7.6 × 10⁻³ Ω cm has been achieved with the 25 wt% ZnO composite film deposited at 500 °C. The photoluminescence spectrum of the composite films shows a decrease in PL intensity with increasing ZnO concentration.     

The nonlinear refraction sign turned to reverse by intercalating cresyl violent dye into layered titanate nanosheets

Solid-state dye-doped materials are an attractive alternative to conventional liquid dye solution. In this study, the spectral characteristics of dye cresyl violet before and after intercalating into layered titanate nanosheets and forming a nanohybrid thin film were investigated by measuring absorption and fluorescence spectra. In addition, their nonlinear optical properties were studied using single beam z-scan technique under irradiation of low power continuous wave (CW) produced by DPSS laser with a wavelength of 532 nm. The nonlinear studying results reveal that the dye cresyl violet in solution has a negative nonlinear refractive index, but it reverses to positive after the dye is intercalated into layered titanate nanosheets with a negative nonlinear refractive index forming CV/HTO nanohybrid thin film. This method can provide a way to turn to reverse nonlinear refraction sign of the materials.     

The effect of an axial external magnetic field on the output power of a small-bore CuBr laser

In this work, the effect of an axial external moveable magnetic field on the output power of a CuBr laser with small-bore tube has been investigated. In all experiments, by applying an EMF along the tube axis, the laser output power has been decreased and by moving the EMF toward the cathode region, more substantial decrease of output power has been observed. The effect is more significant at a magnetic field intensity of 1100 G, Ne gas pressure of 35 Torr, frequency of 19 kHz and voltage of 3.8 kV, such that there was no laser emission when the EMF was placed around the cathode.     

Emission properties of femtosecond (fs) laser fabricated microstructures in Polystyrene (PS)

We fabricated microstructures and micro craters in thin films and bulk of PS. To the best of our knowledge, this is the first report of the emission from fs laser modified regions of PS when excited at 337, 400, 458, 488 and 514 nm wavelengths with different emission peaks. We systematically studied the emission in context of formation of optical centers and analyzed the spectra of irradiated PS. Change in the excitation wavelength leads to a shift in the emission peak, whereby, we infer that the emission should be due to a myriad of optical centers. Interestingly these optical centers have a similar excitation spectrum. Diphenylbutadiene (DPBD) is probably the main optical center among other optical centers thus formed in the process of fs laser irradiation of PS.     

Spectroscopic investigations of femtosecond laser irradiated polystyrene and fabrication of microstructures

We report microfabrication of structures in bulk and thin films of polystyrene (PS) using femtosecond (fs) laser pulses. For the first time to our knowledge, we report emission from the fs laser modified regions of bulk and thin films of PS when excited at 458, 488, and 514 nm. Moreover, we report the existence of peroxide type free radicals, for the first time, in fs laser irradiated bulk PS. We observed the suppression of Raman modes in case of structures fabricated at higher energies and the same effect was noticed in central portion of the structures fabricated. No appreciable broadening was observed in the case of structures fabricated at low energies. Possible applications resulting from such structures are discussed briefly.     

Generation of bubbles in glass by a femtosecond laser

Permanent microscale bubbles with varied size and number density are induced in borosilicate glasses by adjusting the focusing depth (FD) of a tightly focused femtosecond laser. With continuously increasing of the focusing depth, the average size of generated bubbles experiences an increase-decrease process. However, the number density of generated bubbles experiences an opposite changing process compared to the change of the size. The possible mechanism for the bubble generation and changing with the focusing depth has been discussed.     

Remote fiber sensor based on cascaded Fourier domain mode-locked laser

We propose a high-speed remote fiber Bragg grating (FBG) sensor interrogation system based on a 1.3-μm cascaded Fourier-domain mode-locked (FDML) laser. It consists of multiple FBGs connected to an optical circulator in the laser cavity. The cascaded FDML laser with these multiple FBGs is operational when the scanning frequency of the fiber Fabry-Perot tunable filter matches the fundamental frequency of the laser cavity. Each FBG provides a separate laser cavity for the FDML laser. The scanning frequencies of each laser cavity are 30.5314, 31.5393, 32.7108, and 33.8023 kHz. Using the cascaded FDML laser, we measure the performance of the long-distance static strain FBG sensor interrogation system in both the time and spectral domains. The slope coefficients of the measured relative wavelength difference and the relative time delay from the static strain are found to be 0.95 pm/μstrain and 0.15 ns/μstrain, respectively. We also demonstrate the dynamic response of the interrogation system with 80-Hz modulation strain using the cascaded FDML laser. Thus, an FBG sensor interrogation system for high-speed and high-sensitivity long-distance monitoring systems can be realized using a cascaded FDML laser.     

Full L-band coverage of multiwavelength erbium-doped fiber laser

We propose and experimentally demonstrate a dual-pass unbalanced in-line Sagnac interferometer as a novel comb filter for implements in erbium-doped fiber lasers to obtain wide wavebands of multiwavelength radiations with enhancements of signal-to-noise ratios (SNRs). The hybrid combinations of the comb filter with the two schemes of nonlinear polarization rotation and intensity dependent loss have successfully not only enlarged the lasing bandwidth up to 47 nm but also enhanced the SNR up to 40 dB. The simultaneous lasing-wavelengths of 117 channels are also obtained. The multiwavelength lasing spectra with free spectral range of 0.4 nm covering the full L-band are useful for the applications of DWDM and WDM-PON systems.     

A detailed study through the focal region of near-threshold single-shot femtosecond laser ablation nano-holes in borosilicate glass

A detailed study of the morphology of nano-craters drilled in borosilicate glass by single shot femtosecond laser ablation near the ablation threshold has been performed by scanning electron microscopy, atomic force microscopy and scanning electron microscopy imaging after focused ion beam sectioning. The influence of the numerical aperture (NA = 0.4 and 0.8), the pulse energy (16 nJ < E_p < 600 nJ) and the position of the specimen surface into the focal region were systematically investigated, leading to nanometric or micrometric scales in every spatial dimension. The nanocrater’s size is not restricted by the diffraction limit but determined by the laser pulse stability and the material properties. If the beam is focused inside the glass, two craters are drilled, shaping very distinct morphologies. Their dimensions have been studied in details and different relationships have been proposed for the evolutions of the depths and of the various diameters of these craters as functions of the pulse energy, the numerical aperture and the position of specimen surface in the beam-material interaction region. It is suggested that the long, thin conical profile with very high aspect ratio of the secondary craters is due to a spontaneous reshaping of the beam which transforms the incoming Gaussian pulse into a Gaussian-Bessel pulse. As proposed in the developed model the geometry of the second craters seems to be connected with the one of the main craters.     

Calibration of a multiple axes 3-D laser scanning system consisting of robot, portable laser scanner and turntable

A multiple axes 3-D laser scanning system consisting of a portable 3-D laser scanner, a industrial robot and a turntable is demonstrated. By using a criterion sphere, a robot tool center point (TCP) calibration approach is proposed to calibrate the relation between the laser 3-D scanner and the robot end-effector. In this approach, two different translational motions of robot are first made to determine the rotation part, and then at least three different rotational motions are made to determine the translation part. Meanwhile, by using the criterion sphere, a turntable approach is proposed to calibrate the pose of the turntable relative to the robot. In this approach, several rotational angles of turntable and two different heights of the sphere are made to determine the rotational axis of turntable. Experiment is performed on a portable laser scanner mounted on an industrial robot ABB IRB4400 with a turntable. The experiment results show that the two proposed calibration algorithms are stable and flexible. The application of 3-D measurement is also given to demonstrate the effectiveness and stability of the multiple axes 3-D laser scanning system.