激光水下扫描成像系统的图像修正机理

同步扫描系统可以克服后向散射，但同时也产生了两种非线性，一是扫描线速度的非线性，一是由于距离对光能衰减造成的非线性，两种非线性都需要修正，本文从原理上讨论水下激光成像时能量衰减的修正原理与修正方法，并给出仿真结果。     

Changes in the Laser-Induced Fluorescence Spectrum of Myocardium Tissue with Decrease in Its Viability

We investigated the laser-induced fluorescence spectra (LIF) of porcine cardiac tissues with different degrees of viability. The data obtained are compared with the results of routine histological investigations and also with the experiments performed with the use of fluorescent probes. It has been found with a high degree of reliability that the loss of the viability of the myocardium tissue leads to the alteration of its LIF spectra. This can be used for low-invasive rapid control of transplant viability in the process of its preparation and during surgery.     

Submicrometric Displacement and Vibration Measurement Using Optical Feedback in a Fiber Laser

A very simple and efficient technique for the remote sensing of a noncooperative target is presented. This technique is based on the frequency-shifted reinjection of light in a class B laser. Ytterbium- and erbium-doped fiber lasers have both been used to measure displacements with a submicrometric resolution and the vibration power spectrum of an object.     

蓝光相变光盘的多层膜结构设计

为了使光盘获得优良的记录／读出性能并能够长期稳定地使用，必须优化设计相变光盘的多层膜结构。采用自行设计的模拟分析相变光盘读出过程设计软件，从光学角度出发模拟计算了蓝光(405nm)相变光盘的膜层结构，研究了多层膜系的反射率和反射率对比度等光学参量与各层膜厚度和槽深的关系。研究得出的最佳多层膜结构为：下介电层／记录层／上介电层／反射层的厚度对于台记录为100nm／10nm／25nm，／60nm，而对于槽记录则为140nm／15nm／30nm，／60nm，槽深为50nm。模拟计算结果对于将来高密度蓝光相变光盘的制备具有一定的指导意义。     

双预脉冲驱动X射线激光实验研究

 在“星光-Ⅱ”激光装置上进行了双预脉冲驱动类氖铬X射线激光实验，介绍了实验方法和实验结果，并对结果进行了简短讨论。由于目前“星光”装置输出能量较低，所进行的双预脉冲驱动未能显著提高X射线激光强度，改变预脉冲幅度时X射线激光强度也未有显著变化。利用MED103程序进行了模拟计算，其结果与实验结果一致。     

毛细管放电X光激光装置中的预脉冲电源

 针对目前毛细管放电X 光激光装置产生的预脉冲电流幅值过大、持续时间较短的问题，提出了增加预脉冲开关抑制原有预脉冲，再外加由脉冲成形网络组成的预脉冲发生器，产生所需预脉冲的改造方案。可在主脉冲来临之前产生幅度10~50A，持续时间约17μs的方波预脉冲电流，来满足毛细管放电泵浦类氖氩X光激光实验的需要。     

Rotation of a Fine Particle with Circularly Polarized Anti-Parallel Collinear Laser Beams

We have succeeded in the operation of rotating a fine particle which was held without mechanical contact by circularly polarized laser beams with opposite propagation directions. A polystyrene latex particle 11.9 μm in diameter deformed in a disk-like shape was dispersed in water, and was trapped using the anti-parallel collinear laser beams which were set up so that they had the circular polarization rotating in the same direction. It was observed that the trapped particle rotated in the same direction as the rotation of the circular polarization of light. Inversion of the rotational direction of the circular polarization of light reversed the direction of the rotation of the particle. Although the rotational speed of a particle varied significantly from particle to particle, it was found to be proportional to the laser beam intensity. A typical value for the rotational speed per beam intensity was 2.1 Hz/W.     

一种控制掺铒光纤激光器超混沌的方法——非线性延时反馈参数调制法

提出一种非线性延时反馈参数调制法来控制混沌/超混沌，给出了利用这种方法控制处于超混沌状态的双环掺铒光纤激光器的方案.数值模拟表明，只要延时时间和反馈强度合适就可以把双环掺铒光纤激光器从超混沌状态成功地控制到不同的周期状态. 关键词： 掺铒光纤激光器 超混沌 非线性延时反馈参数调制 混沌控制     

Study of the pulsed laser vapor doping of Si(1 0 0) with KrF excimer laser and BCl3 gas

The properties of pulsed laser vapor doping on p-Si(1 0 0) with a KrF (248 nm) excimer pulsed laser (248 nm) and BCl₃ gas are reported in this paper. The doped samples are characterized by the resistance measured using a four-probe method, since the sheet resistance changes with the carrier concentration of the sample. The doping effects with the variation of laser energy density, pulse number, and the pressure of BCl₃ were investigated in terms of the sheet resistance. In this way, the optimized parameters were obtained and used for the positive heavy doping on p-Si(1 0 0) and p-Si(1 1 1). Then, using a square mesh under the above conditions, an image doping was completed. Finally, the metal–semiconductor Ohmic contacts were realized by plating Ag and Cu films on the doped surface.     

A simple model for high fluence ultra-short pulsed laser metal ablation

The ultra-short laser metal ablation is a very complex process, the complete simulation of which requires applications of complicated hydrodynamics or molecular dynamics models, which, however, are often time-consuming and difficult to apply. For many practical applications, where the laser ablation depth is the main concern, a simplified model that is easy to apply but at the same time can also provide reasonably accurate predictions of ablation depth is very desirable. Such a model has been developed and presented in this paper, which has been found to be applicable for laser pulse duration up to 10 ps based on comparisons of model predictions with experimental measurements.