Technological quality determination of pharmaceutical disintegrant by DSC cooling and DSC photovisual

A number of disintegrants are available on the market. They improve tablets’ disintegration. The objective of this work is the comparison of the technological quality parameters of disintegrants using different analytical techniques. Three batches of disintegrants and their binary mixtures (water:disintegrants) were investigated. Cooling experiments were used from –30 up to 200°C. The data obtained showed calorimetric differences between the samples. In the binary mixtures water showed different crystallization behaviour from the one found in the literature. According to the results DSC technique helped the quality control of different disintegrants.     

Carburizing of titanium with plasma jets under reduced pressure

The carburizing of titanium with argon-methane (0.1%) and argon-methane (0.1%)-hydrogen (2%) plasma jets at a pressure of 200 Torr was studied. The carburizing of titanium was not successful with the argon-methane plasma jet because the specimen was covered with graphitic carbon. A hard and thick TiC layer was formed by the argon-methane-hydrogen plasma jet in a short time without the deposition of graphitic carbon. Emission spectra from the plasma jets show that the addition of hydrogen increases the amount of CH radicals as well as decreases the amount of C₂ and C in the plasma jet. The decrease of C₂ and C suppresses the deposition of graphitic carbon and enhances the TiC formation.Partly presented at Gordon Research Conference on Plasma Chemistry, August 11–15, 1986, Tilton, New Hampshire.     

Modelling of the pressure-velocity correlation in turbulence diffusion

Most current computations of trubulent flows with second-moment closure adopt the diffusion models which neglect the effect of pressure-velocity correlation. In the present paper the importance of this correlation effect is elucidated the neglect of this effect accounts for some major defects in the wide application of the second-moment closures. Through the relation between and , established by Lumley, we propose here a new turbulence diffusion model which takes into consideration the pressure effect. Applications of this new model in the computation of shearless turbulence mixing layer and plane and round-jet flows show that the spreading rate of these flows can be satisfactorily captured.     

Fouling Mitigation in a Heat Exchanger: High Cycles of Concentration for a Cooling-Tower Application

The purpose of the present study is to investigate the effect of a physical water treatment (PWT) technology on fouling mitigation in a simulated cooling tower operating at high cycles of concentration. Hard water was produced by evaporating pure water in a circulating open cooling tower, where dissolved calcium carbonate ions became concentrated with time. Heat transfer tests were conducted in a rectangular channel by varying the cycle of concentration (COC) from 5 to 10, and fouling resistances were measured over 270 hrs for each case with and without the PWT treatment. Another test was conducted with no blowdown case with and without the PWT treatment. The fouling resistance at 5 cycles with the PWT treatment was about 70% less than that in the case without the PWT treatment at the end of 270-hr tests. Even at 10 cycles, the PWT treatment reduced the fouling resistance by 60% from the value for the no treatment case. Thus, one can conclude that the PWT technology can help circulating cooling-tower water at relatively high COC for significant freshwater conservation, while keeping fouling resistances below industry standards.     

Cooling Characteristics During Bath Quenching of Test Probe Using Inverse Heat Transfer

It is of engineering importance to accurately predict the surface cooling characteristics in bath quenching of metals and alloys. In this investigation, the surface cooling characteristics in quenching of Wolfson probe are estimated with reasonable accuracy by solving an inverse heat conduction problem. Regularization method is used for smoothening the input temperature measurements at probe center, for superior inversion estimates. The reverse pool-boiling curve is captured on bath quenching characteristic, plotted as cooling velocity versus surface temperature. The prime advantage is the bypassing of convection coefficients, which are uncertain in pool boiling.     

Shock cooling of liquid nitrogen and superfluid helium

Abstract

Superfluid Helium (11) and liquid nitrogen are the only liquids which have been shown experimentally, to exhibit shock cooling. In the present paper we use the Landau model to demonstrate theoretically that the roton gap, which decreases with increasing density, plays the same role leading to shock cooling in liquid helium as the dissociation energy does in liquid nitrogen.     

Performance investigation of an advanced tracked prime mover on the low bearing soil

This study has presented a performance investigation of an advanced tracked prime mover for the operation of agricultural goods and other operations on peat terrain. The maximum and continuous traction torque of the prime mover has been developed by designing an advanced controller for controlling the intelligent system. The prime mover’s mobility is studied with ultrasonic displacement sensor, torque transducer, National Instrument cRIO-9004 Compact-RIO Real-time Controller Unit (RCU), a National Instrument TPC 2106T Touch Panel Control (TPC), a Trimble AG132 GPS antenna and receiver unit, and a Dlink DIR-655 router. The fuzzy logic controller (FLC) has been equipped with the prime mover hydraulic system to increase the traction torque of the hydraulic motor when the prime mover’s sinkage is more than or equal to 70 mm. The prime mover’s design demonstrates good potential in traversing peat terrain as the measured tractive effort was found to be 48% of the vehicle’s gross weight while the recommended tractive effort is in the range of 30–36% of the vehicle’s gross weight.     

真空冷却过程中实验条件对真空冷却速率的影响

以熟肉为实验材料,对实验条件对真空冷却速率的影响进行了理论分析和实验研究。实验结果表明:真空室有效容积越小、真空泵抽速越高,则真空冷却时间就会越短;冷阱温度对真空冷却速率有着明显的影响;当真空室内的最终压力在0.4～0.61kPa变化时,熟肉的表面温度一直在0℃以上,其真空冷却的时间随着真空室内压力的升高而增加。而真空室内的最终压力在0.3kPa左右时,熟肉的表面温度在真空冷却过程会低于0℃。     

Performance of a silicon monochromator under high heat load

The performance of a cryogenically cooled double‐crystal silicon monochromator was studied under high‐heat‐load conditions with total absorbed powers and power densities ranging from 8 to 780 W and from 8 to 240 W mm^?2, respectively. When the temperature of the first crystal is maintained close to the temperature of zero thermal expansion of silicon, the monochromator shows nearly ideal performance with a thermal slope error of 0.6 µrad. By tuning the size of the first slit, the regime of the ideal performance can be maintained over a wide range of heat loads, i.e. from power densities of 110 W mm^?2 (at total absorbed power of 510 W) to 240 W mm^?2 (at total absorbed power of 240 W).