Fouling Mitigation in a Heat Exchanger: High Cycles of Concentration for a Cooling-Tower Application

The purpose of the present study is to investigate the effect of a physical water treatment (PWT) technology on fouling mitigation in a simulated cooling tower operating at high cycles of concentration. Hard water was produced by evaporating pure water in a circulating open cooling tower, where dissolved calcium carbonate ions became concentrated with time. Heat transfer tests were conducted in a rectangular channel by varying the cycle of concentration (COC) from 5 to 10, and fouling resistances were measured over 270 hrs for each case with and without the PWT treatment. Another test was conducted with no blowdown case with and without the PWT treatment. The fouling resistance at 5 cycles with the PWT treatment was about 70% less than that in the case without the PWT treatment at the end of 270-hr tests. Even at 10 cycles, the PWT treatment reduced the fouling resistance by 60% from the value for the no treatment case. Thus, one can conclude that the PWT technology can help circulating cooling-tower water at relatively high COC for significant freshwater conservation, while keeping fouling resistances below industry standards.     

Cooling Characteristics During Bath Quenching of Test Probe Using Inverse Heat Transfer

It is of engineering importance to accurately predict the surface cooling characteristics in bath quenching of metals and alloys. In this investigation, the surface cooling characteristics in quenching of Wolfson probe are estimated with reasonable accuracy by solving an inverse heat conduction problem. Regularization method is used for smoothening the input temperature measurements at probe center, for superior inversion estimates. The reverse pool-boiling curve is captured on bath quenching characteristic, plotted as cooling velocity versus surface temperature. The prime advantage is the bypassing of convection coefficients, which are uncertain in pool boiling.     

Shock cooling of liquid nitrogen and superfluid helium

Abstract

Superfluid Helium (11) and liquid nitrogen are the only liquids which have been shown experimentally, to exhibit shock cooling. In the present paper we use the Landau model to demonstrate theoretically that the roton gap, which decreases with increasing density, plays the same role leading to shock cooling in liquid helium as the dissociation energy does in liquid nitrogen.     

颈内静脉原位导丝法换置中心静脉长期血液透析导管的临床应用

目的探讨经颈内静脉原位导丝法换置中心静脉长期血液透析导管在维持性血液透析（MHD）患者中的应用价值。方法选取近3年在颈内静脉留置的中心静脉长期血液透析导管因功能障碍后，并经颈内静脉原位导丝法换置长期导管，术后及每次透析后均改用尿激酶封管患者16例（原位换置组）；选取同期首次经颈内静脉留置中心静脉长期血液透析导管,普通肝素封管患者20例作为对照组；分析两组患者围术期泵控血流量及随访期的反应及开存期率、次开存期率。结果围术期泵控血流量原位换置组高于对照组，有统计学差异（P＜0.05）；两组比较感染例次/1000导管日0.9%与1.0%，无统计学差异（P＞0.05）。原位换置组围术期未发生中重度并发症，12个月开存期率81.2%、次开存期率93.8%；对照组开存期率为65%、次开存期率85%；两组比较无统计学差异（P＞0.05）。结论颈内静脉原位导丝法换置中心静脉长期血液透析导管，在MHD患者中的使用是安全的、可行的。     

Performance investigation of an advanced tracked prime mover on the low bearing soil

This study has presented a performance investigation of an advanced tracked prime mover for the operation of agricultural goods and other operations on peat terrain. The maximum and continuous traction torque of the prime mover has been developed by designing an advanced controller for controlling the intelligent system. The prime mover’s mobility is studied with ultrasonic displacement sensor, torque transducer, National Instrument cRIO-9004 Compact-RIO Real-time Controller Unit (RCU), a National Instrument TPC 2106T Touch Panel Control (TPC), a Trimble AG132 GPS antenna and receiver unit, and a Dlink DIR-655 router. The fuzzy logic controller (FLC) has been equipped with the prime mover hydraulic system to increase the traction torque of the hydraulic motor when the prime mover’s sinkage is more than or equal to 70 mm. The prime mover’s design demonstrates good potential in traversing peat terrain as the measured tractive effort was found to be 48% of the vehicle’s gross weight while the recommended tractive effort is in the range of 30–36% of the vehicle’s gross weight.     

附加压力与分散系统的稳定性

较详细地讨论了附加压力与分散系统稳定性间的关系,指出分散相附加压力的降低是分散系统趋向稳定的根本原因。以乳状液为例,附加压力降低不仅减少了液滴间相互碰撞的概率,而且更重要的是,它与液滴表面形成牢固的保护膜密切相关。只有当液滴的附加压力趋近0时,分散系统才达到热力学上稳定的状态,此时乳状液已变成了微乳状液。上述讨论也基本适用于固/液分散系统。     

真空冷却过程中实验条件对真空冷却速率的影响

以熟肉为实验材料,对实验条件对真空冷却速率的影响进行了理论分析和实验研究。实验结果表明:真空室有效容积越小、真空泵抽速越高,则真空冷却时间就会越短;冷阱温度对真空冷却速率有着明显的影响;当真空室内的最终压力在0.4～0.61kPa变化时,熟肉的表面温度一直在0℃以上,其真空冷却的时间随着真空室内压力的升高而增加。而真空室内的最终压力在0.3kPa左右时,熟肉的表面温度在真空冷却过程会低于0℃。