CdS/SiO2复合材料的低频Raman散射研究

对用溶胶凝胶法制备的ＣｄＳ／ＳｉＯ２复合材料进行低频Ｒａｍａｎ散射研究，结果表明可从其低频Ｒａｍａｎ散射峰位计算出ＣｄＳ微晶的粒径，两种不同的低频振动模式由激发光的两种偏振方向加以区分，低频Ｒａｍａｎ散射射的二级散射峰根据实验结果加以指认，所得平均粒径结果与透射电镜观察结果有较好的对应关系，复合材料吸收光谱吸收边蓝移与ＣｄＳ纳米子粒径之间存在着密切的关系，实验证明，样品吸收边能量与ＣｄＳ平均粒径的     

Adsorption Behavior of a Water-soluble Porphyrin at the Glass-water Interface as Studied by Synchronous Total Internal Reflection Fluorescence Spectroscopy

Total imernal reflection fluorescence spectroscopy (TIRF) and synchronous scanning technique were combined to study the adsorption behavior of the meso-tetrakis (4-sulfonatophenyl)porphyrin (TPPS) at the glass-water interface without any surfactant. The pH dependence of synchronous fluorescence signal at the interface was analyzed. Both unprotonated (TPPS^4-) and diprotonated (H2TPPS^2-) forms of TPPS were observed at the interface. But the interface favored the adsorption of. The apparent estimated pKa2 value shifted from 5.00 in the bulk solution to 2.7 at the interface. STIRF provides a good technique to study multi-component systems at the interface.     

Scattering spectra and colour of disperse systems of low-absorptive particles

In this article, the results of calculations of scattering spectra of low-absorptive spherical particles are presented. It was obtained using different approximate and numerical methods. The comparative evaluations of application of single scattering approximation, the average field approximation and of the methods of computer modeling on the basis of Monte-Carlo method on various scattering multiplicity were performed. The comparison demonstrates the good agreement of calculated results with experimental scattering spectra of eye lens. By using the obtained spectral data the colour coordinates are calculated. The regularities of changes in colour characteristics in dependence of disperse system parameters are analyzed.     

纤维素/甲壳素共混膜的结构表征与抗凝血性能

以 6wt %NaOH 4wt%尿素为纤维素的新溶剂 ,采用溶液共混法制备出纤维素 甲壳素共混膜 ,为甲壳素在碱性溶液中制膜提供了新的方法 .红外光谱、X 射线衍射、扫描电镜和力学性能、抗凝血性能测试结果表明 ,共混膜中甲壳素含量低于 4 0wt%时 ,纤维素与甲壳素分子间具有良好的相容性 ;在纤维素中引入适量甲壳素可提高共混膜的抗张强度 ,共混膜的干、湿态抗张强度在甲壳素含量 10wt%时最大 ,其值分别为 89 1MPa和 4 3 7MPa ,比纯态纤维素膜的干、湿态抗张强度分别提高了 6 7%和 11 5 % ;甲壳素的引入可明显降低血小板在共混膜表面的粘附、凝聚与变性 ,增大共混膜的抗凝血参数 ,甲壳素含量达到 5 0wt%时 ,该共混膜具有良好的抗凝血性能     

Thermal characterization and thermal degradation of poly(norbornene-2,3-dicarboxylic acid dialkyl esters) synthesized by vinyl addition polymerization

The thermal properties and degradation behaviors of poly(norbornene-2,3-dicarboxylic acid dialkyl esters) (PNB-dialkyl esters) (alkyl = Me (PNB-Me), Et (PNB-Et), Pr (PNB-Pr), and Bu (PNB-Bu)) were investigated by thermogravimetric analysis (TGA) in dynamic conditions and by infrared (IR) spectroscopy. The PNB-dialkyl esters show good thermal stability up to 350 °C, and the thermal stability decreases in the order Me > Et > Pr > Bu with the increase in size of side chain. The effect of side-chain size on the thermal degradation behaviors of PNB-dialkyl esters is evidenced by one-step thermal degradation profile for PNB-Me while two-step thermal degradation profile for PNB-Et, PNB-Pr, and PNB-Bu. Transformation is deduced to undergo β-hydrogen elimination and formation of anhydride group in the first stage of thermal degradation reaction according to TGA and IR results for PNB-Et, PNB-Pr, and PNB-Bu. The apparent activation energy and thermal degradation model of PNB-dialkyl esters are estimated by means of Ozawa-Flynn-wall method and Phadnis-Deshpande method, respectively.     

1－芳酰基－4－芳基氨基脲类化合物的合成及表征

利用N－取代三氯乙酰胺与芳基酰肼反应，合成了6个新的1－芳酰基－4－芳基 氨基脲类化合物，其结构经IR，^1H NMR和元素分析证实。初步生物活性测试表明 ，具有一定的除草活性。     

超大孔磷酸铝分子筛的合成及性能

1988年Davis等首次报道了以二正丙胺和四丁基氢氧化铵为结构导向剂合成出一种命名为VPI-5的新型磷酸铝超大孔分子筛。它是一族具有相同三维拓朴学骨架的磷酸铝系分子筛,该结构的对称性属六方晶系,P6_3cm空间群,单位晶胞由36个TO_2组成,晶胞参数α=1.8989nm,c=0.8112nm,其主孔道由18员环构成,孔直径约为1.2-1.3nm。     

Modification of Surface and Structural Properties of Ordered Mesoporous Silicates

Two simple modification methods for ordered mesoporous silicas were examined and compared. MCM-41 molecular sieve was physically coated with 4-cyano-4-biphenyl [4(4-pentenyloxy)]benzoate (CBPB) and chemically modified using trimethylethoxysilane. The structural and surface properties of the obtained materials were characterized using elemental analysis, thermogravimetry and nitrogen adsorption over a wide pressure range.It was shown that the pore size of the MCM-41 material was not decreased significantly after the coating procedure, even for high loadings of CBPB. Moreover, low pressure adsorption measurements indicated that significant fractions of the MCM-41 surface were not covered by CBPB, even for high CBPB loadings, which suggests that the attained coverage may be very nonuniform. The chemical bonding procedure led to a marked decrease in the pore size and change of surface properties.It was demonstrated that nitrogen adsorption measurements provide a means of a thorough characterization of modified MCM-41 materials, allowing to estimate the surface area, pore volume and pore size distribution. Moreover, low pressure adsorption data can be used to qualitatively or semiquantitatively assess the surface coverage of the coated/bonded organic groups, which may be used to estimate the uniformity of the coverage and therefore, the usefulness of the modification procedure.     

Synthesis and Characterization of a Novel Biomaterial： Maleic Anhydride-modified Poly（dl-lactic acid）

A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA‘s hydrophilicity and cell affinity and to provide reactive groups for further chemical modification. FTIR, ^13 C NMR and DSC were used to characterize the maleic anhydride-modified PDLLA.     

High temperature corrosion behaviour of M(Co,Ni)CrAIY-coatings on high temperature materials-microanalytical investigations

In our former investigations, the phenomenon high temperature corrosion (HTC) was described exemplarily on selected materialcoating combinations for blades of stationary gas turbines, mainly in the temperature region of up to 750° C. To answer the question, in which manner higher gas inlet and/or higher material surface temperature would influence the HTC behaviour, a special analytical technique—the integral layer profile analysis—was introduced to ameliorate concentration profile methods. By examining IN 738 LC specimens with CoCrAlY plasma spray coating, stressed by hot gas at 900° C, the limits of this system are shown by explaining the corrosion mechanism; the method is also used for other systems, e.g. U 520 with NiCrAlY coating at 750° C.