四苯基卟啉铂电致发光性能的研究

四苯基卟啉铂(PtTPP)可以作为红光掺杂材料制备有机电致发光器件，采用的器件结构为[ITO／CuPc／NPB／BePP2：PtTPP／LiF／Al]，其中BePP2：PtTPP的共沉积膜作为发射层．实验结果表明在发射层中存在着从BePP2到PtTPP的能量传递．通过改变掺杂层中PtTPP的浓度来考察器件的性能，当PtTPP的掺杂浓度在8％(物质的量比)时，器件呈现纯正的红光发射，发射峰位于668nm，器件的效率为0．004lm／W．     

Investigation on spontaneous ignition of two kinds of organic material with water

A systematic investigation was performed to elucidate the cause of spontaneous ignition of Refuse Derived Fuel (RDF) and Meat Bone Meal (MBM). Heat generation in both RDF and MBM with addition of water liquid and vapor at room temperature was determined by isothermal calorimetry. Compared with water liquid, the heat of wetting by sorption of water vapor at 80% relative humidity and 25 °C was larger, which can raise the temperature of RDF and MBM more than 30 and 56 °C, respectively. Heat generation due to fermentation occurred and the temperature of RDF and MBM reached or exceeded 80 °C after 5 days for RDF and 4 days for MBM at 100% RH. The spontaneous ignition for RDF and MBM results from heat of wetting and fermentation at room temperature and a further exothermic reaction at higher temperature.     

Synthesis and electrochemical properties of Zn3V3O8 as novel anode material

Zn₃V₃O₈ two-dimensional micro sheets are successfully synthesized by combination of solvothermal method and heat treatment. The Zn₃V₃O₈ has better electrochemical performances after calcinations.     

电化学合成镍配合物的研究

采用金属镍为“牺牲”阳极，首次在无隔膜电解槽中，电化学溶解金属镍一步 制备了纳米NiO前驱体Ni(Oet)2,Ni(Obu)2,Ni(Oet)2(acac)2，Ni(Obu)2(acac)2 [acac为乙酰丙酮基].产物通过红外光谱（FT-IR）、拉曼光谱（Raman spectrum） 进行表征。同时讨论了影响电合成镍醇盐及其配合物的关键因素。实验表明，防止 阳极钝化，温度控制在30-40℃，采用有机胺溴化物为导电盐，可以提高电合成效 率。     

反相液相色谱用球形共聚物柱填料

采用新颖聚合工艺制备用于反相高效液相色谱柱填料的乙基苯乙烯-二乙烯苯球形共聚物,不需使用备有高速搅拌的混匀器和特殊的筛析设备,聚合物粒径的95％在3～7μm之间,测算了渗透性、柱效和峰不对称性等柱参数,并通过分离实例说明该填料对胺类、酚类和芳烃类具有优良分离性能。     

电化学合成铜配合物的研究

采用金属铜为"牺牲"阳极,首次在无隔膜电解槽中,电化学溶解金属铜一步制备了纳米CuO前体Cu(OEt)2, Cu(OBu)2, Cu(acac)2, Cu(OEt)(acac), Cu(OBu)(acac) (acac为乙酰丙酮基).产物通过红外光谱(FT-IR)、拉曼光谱(Raman spectrum)进行表征.同时讨论了影响电合成铜醇盐及其配合物的关键因素.实验表明,防止阳极钝化,温度控制在30～50 ℃,采用有机胺溴化物为导电盐, 电极电位控制在0.8～1.2 V之间,可以提高电合成效率.实验同时表明Cu(acac)2, Cu(OEt)(acac), Cu(OBu)(acac)可作为制备含铜纳米材料前驱体.     

Carbon anode materials from polysiloxanes for lithium ion batteries

Three kinds of silicon-containing disordered carbons have been prepared by pyrolysis of polysiloxanes with different amounts of phenyl side groups. X-ray powder diffraction, X-ray photoelectron spectroscopy and electrochemical capacity measurements were performed to study their behaviors. Graphite crystallites, micropores, and silicon species affect their electrochemical performances. All of them present high reversible capacities, >372 mAh/g. Since the graphite crystallites are very small, they contribute very little to reversible capacity. The number of micropores produced by gas emission during the heat-treatment process decides whether they exhibit reversible capacity. Si mainly exists in the form C–Si–O and influences the irreversible capacity. There is no evident capacity fading in the first ten cycles, indicating promising properties for these disordered carbons.     

Preparation and characterisation of thermoresponsive poly[(N-isopropylacrylamide-co-acrylamide-co-(hydroxyethyl acrylate)] microspheres as a matrix for the pulsed release of drugs

Despite the large number of publications and patents concerning pH/thermoresponsive polymers, few data are available concerning the preparation of thermoresponsive cross-linked microspheres from preformed polymers. Therefore, N-isopropylacrylamide-co-acrylamide-co-(2-hydroxyethyl acrylate) copolymers were obtained as a new thermoresponsive material with a lower critical solution temperature (LCST) around 36 degrees C, in phosphate buffer at pH 7.4, and with a cross-linkable OH group in their structure. The LCST value was determined both by UV spectroscopy and microcalorimetric analysis. These copolymers were solubilised in acidified aqueous solution below their LCST, dispersed in mineral oil, and transformed into stable microspheres by cross-linking with glutaraldehyde. The thermoresponsive microspheres were characterised by optical and scanning electron microscopy, degree of swelling, and water retention. The pore dimensions of the microspheres and the retention volumes of some drugs and typical compounds were evaluated at different temperatures by liquid chromatography. Indomethacin, as a model drug, was included in the microspheres by the solvent evaporation method. Finally, the influence of temperature and of temperature cycling on drug release was investigated.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

电极材料对NPB/Alq3有机电致发光器件性能的影响

采用不同材料作为有机电致发光器件(OELDs)的电极, 制备了基本结构为[阳极/NPB(40 nm)]/Alq3(50 nm)/阴极]的异质结双层器件, 并通过改变OELDs器件的阴极或阳极来研究电极材料对器件光电性能的影响. 研究结果表明, 各器件电流-电压(I-V)关系的基本特征与陷阱电荷限制电流(TCLC)机制的拟合情况相符. 由于有机材料本身能级的无序性以及载流子迁移率对温度和电场的依赖性, 不同电极的载流子注入能力与其功函数并无直接关系. 双层器件中由于空穴传输层的引入, 使得载流子复合区域位于有机层异质结界面处, 降低了金属阴极对激子的猝灭作用, 从而大大提高了器件性能. 此外, 金属电极OLEDs器件结构具有的微腔效应会导致发射光谱的位移和谱峰宽度变窄, 这表明通过对金属电极的表面改性和优化可使器件性能超过常规结构的器件.