SiO2/炭泡沫和SiC/炭泡沫复合材料的制备及表征

对炭泡沫为支撑骨架的氧化硅气凝胶(SiO₂/炭泡沫)和碳化硅(SiC/炭泡沫)复合材料分别采用XRD、SEM、激光导热仪、万能力学试验机进行物相、微观结构、热学及力学性能方面的表征.结果表明:所制备的SiO₂/炭泡沫与原炭泡沫相比,具备更高的抗压强度(14.95 MPa)和更低的室温热导率(0.44 W·m^-1·K^-1).SiC/炭泡沫材料则保持了较高的抗压强度值(14.66 MPa),其在 1 200 ℃下具备极低的高温热导率(2.18W·m^-1·K^-1).热重分析表明,SiC/炭泡沫在氧化氛围中到610 ℃才发生质量的损失,而内部炭发生完全烧蚀的温度高达844 ℃,这表明该材料的抗氧化性能远好于纯的炭泡沫材料.     

Oil Base Mud. Part I: Synthesis of Some Local Surfactants Used as Primary Emulsifiers for Oil Base Mud and Evaluation of Their Rheology Properties

Six oil soluble nonionic surfactants with different HLBs have been prepared. Their HLBs situate between 3.9 and 6.7. Transesterification was carried out for glycerol and triethanol amine with oleic acid at different moles to obtain six emusilifiers. They named glycerol momooleate (I), glycerol diooleate (II), glycerol trioleate (III), triethanol amine mono-, di- and tri-oleate (IV), (V,) and (VI). The chemical structure was confirmed using; the elemental analysis, FTIR and ¹HNMR. They were evaluated as a primary emulsifiers (PE) for thdrilling fluids (oil base mud) comparing with a currently used primary emulsifier (Fc). The water in oil base mud (w/o emulsions) was prepared. The concentration of emulsifiers and their HLB exhibited interesting rheology properties including shear-thinning behavior, yield value, viscoelastic effects, thixtropy, gel strength, and filtration loss. The rheology properties of such emulsions strongly depended on the average size distribution of the dispersed droplets that could be varied both with the bulk concentration and HLB value of the emulsifiers. The interfacial and surface properties of these emulsifiers suggest that the droplet size of the dispersed phase and bulk concentration are strongly related to the HLB value of emulsifiers. The w/o emulsion (mud formulation) stability is sensitive to the droplet size of the dispersed phase and HLB value of the used emulsifier. The results were discussed on the light the chemical structure of the primary emulsifiers and the emulsion ingredients.     

A transflective and viewing angle controllable blue-phase liquid crystal display

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-side in-plane switching (DS-IPS) electrode structure is proposed. This structure shows the transflective characteristics because the bottom electrodes are made by aluminium material. For transflective displays, it exhibits a well-matched voltage-dependent transmission and reflection curves through designing the width and gap of the top electrodes. When a bias voltage is applied on the top electrodes, it exhibits as a good viewing angle controllable display.     

The liquid crystal properties of symmetric and non-symmetric dimers based on the azobenzene mesogenic group

A novel system of symmetric and non-symmetric dimers containing azobenzene groups has been synthesized and studied in an attempt to understand further the molecular origins of the intercalated smectic phases. For the non-symmetric dimers, the lack of symmetry was derived solely from the differences in length of the two terminal alkyl chains. Both the spacer and terminal chain lengths were varied. The spacer length was found to exert a profound influence on the clearing temperatures of these materials and a large odd-even effect was observed for the series. The smectic A phase stability was observed to increase with the terminal chain length, yet decrease with increasing spacer length. X-ray diffraction has revealed the structure of the smectic A phase of both the symmetric and non-symmetric azobenzene dimers to be of the monolayer type and not intercalated. The existence of the intercalated phase has previously been explained in terms of either a charge-transfer interaction, or by an electrostatic quadrupolar interaction. However, it has been thought that it may also be the result of an excluded volume or space filling constraint. For the non-symmetric liquid crystal dimers described here, a charge-transfer interaction should be minimal, as should the stabilization from the quadrupolar interaction between the two mesogens. However, it appears that some sort of specific interaction is required to stabilize the intercalated structure.     

基于主动式时间反转镜的声呐目标强度测量研究

为提高目标强度测量过程中的抗噪声、混响以及浅海多途干扰性能,从军标文件中的目标强度测量方法以及主动式时间反转镜的基本原理出发,经过研究和推演,发现可将基于单阵元的主动式时间反转镜与相关器结合应用于目标强度测量过程,提出了一种新的目标强度测量方法。该方法利用了主动式时间反转镜的抗多途特性,使得测量具有抗多途的性能;利用噪声与信号的不相关特性,算法结合相关器起到了很好的抗随机噪声效果;混响中的体积混响是随机的,算法具有抗体积混响的性能。论文分别从理论仿真和水池实验验证了算法的有效性和正确性。     

The mosaic structure design to improve the anchoring strength of SiOx@C@Graphite anode

Silicon oxide (SiO_x)-based anodes have aroused great interest as the most promising alternative anode in the practical application of high-performance lithium-ion batteries. However, the electrochemical performance is inhibited because of the large volume change, and the electrode structure deteriorates during the cycling process, which hinders their practical application. In this article, a novel fabrication method for the synthesis of high-performance SiO_x@C@Graphite composites is presented. SiO_x particles are anchored on the graphite surface by chemical vapor deposition and compression molding. This structure makes up the shortcomings of poor electrical conductivity and poor bonding strength between SiO_x and graphite particles. It is beneficial to form a stable solid electrolyte interface and helps to maintain the structural integrity of electrode materials. As a result, the synthetic SiO_x@C@Graphite anode shows a high reversible capacity (2698.8 mA h), excellent cycle stability (about 76.9% capacity retention for 500 cycles) and a superior rate ability. Our research hopes to provide a new idea for improving the bonding strength of the surface coating.     

Tailoring the dielectric properties and energy storage density of 1−x(0.94NaNbO3−0.06SZ)−xBi2O3 through substitution strategy

Energy storage using dielectric capacitors is a growing area of research and development. However, designing a highly performing dielectric capacitor is still a challenge. Despite the excellent results achieved in lead-based dielectrics, lead-free substitutes are essential because of the environmental concerns associated with lead-based products. The lead-free 1?x (0.94NaNbO₃? 0.06SrZrO₃)+ x Bi₂O₃ ceramics abbreviated NNSZ + xB for x = 0.0, 0.05, 0.1, 0.15, and 0.20 was fabricated via solid-state reaction. A recoverable energy density of 2.93 J cm?³ was obtained for NNSZ+0.1B, associated with high thermal stability (25–130 °C), excellent cycling (N = 10⁵), and high efficiency (η) of 83.5%. Moreover, the introduction of Bi₂O₃ significantly improved the electrical insulation (?_r at 1 kHz = 1608 and tan δ = 0.0038) and breakdown strength (380 kVcm?¹) of NNSZ+0.1B by minimizing the formation of sodium, bismuth, and oxygen vacancies. The results obtained in this study provide a benchmark for further investigations on NaNbO₃-based ceramics. More importantly, this study suggests that NNSZ + xB ceramics can be used in pulsed power technology.     

Surface modification of PBO fibers with 2,2-Bis (3-amino-4-hydroxyphenyl) hexafluoropropane in supercritical carbon dioxide for enhancing interfacial strength

PBO fiber is one of the most promising reinforcements in resin matrix composite because of its excellent mechanical properties. However, the inert and smooth surfaces make it the poor interface adhesion with resin matrix, which seriously limits the application in composites. In this article, we report a method to modify the surface of PBO fibers with 2,2-Bis (3-amino-4-hydroxyphenyl) hexafluoropropane（BisAPAF）in supercritical CO₂ to enhance interfacial properties. Chemical structures, surface elemental composition and functional groups, and surface morphology were characterized by FT-IR spectrometer, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM), respectively. The mechanical properties of the samples were tested by a tensile tester. Static contact angle and microdebonding tests were used to characterize the wetting ability and interfacial shear strength (IFSS) of the fiber and epoxy resin. The results showed that the BisAPAF could be solved in scCO₂ and introduced more groups, –NH₂, –OH, and –CF₃ on the fiber surface, resulting in the mechanical properties and the wettability of PBO fiber slightly improved. Moreover, the fiber surface roughness was also increased obviously. The IFSS between the modified PBO fiber and epoxy resin increased from 8.18 MPa to 31.4 MPa when the treating pressure was 14 MPa. In general, the method to modify PBO fibers surface using BisAPAF in scCO₂ can effectively improve their interfacial properties.     

Binding Characteristics Study of DNA based Aptamers for E. coli O157:H7

E. coli O157:H7 is a pathogenic bacterium producing verotoxins that could lead to serious complications such as hemolytic uremia syndrome. Fast detection of such pathogens is important. For rapid detection, aptamers are quickly gaining traction as alternative biorecognition molecules besides conventional antibodies. Several DNA aptamers have been selected for E. coli O157:H7. Nonetheless, there has not been a comparative study of the binding characteristics of these aptamers. In this work, we present a comprehensive analysis of binding characteristics including binding affinity (K_d) and binding capacity (B_max) of DNA-based aptamers for E. coli O157:H7 using qPCR. Our results show that aptamer E18R has the highest binding capacity to E. coli 157:H7 and the highest specificity over non-pathogenic E. coli strains K12 and DH5α. Our study also finds that the common biotin-tag modification at 5′ end typically changes the binding capacity significantly. For most of the selected aptamers, the binding capacity after a biotin-tag modification decreases. There exists a discrepancy in the binding capability between the selected aptamer and the aptamer used for detection. Our study also shows that a lower concentration of Mg²⁺ ions in the binding buffer leads to a decrease in the binding capacity of E17F and E18R, while it does not affect the binding capacity of S1 and EcoR1.