风力发电机组变速恒频控制系统研究

全面介绍了一种最新应用于风力发电中的新型电机—无刷双馈电机，并分析了这种新型电机作变速恒频运行的原理并对这种电机进行了动态特性仿真研究，给出了形式简洁的控制方程和易于实现的控制方案。     

分形介质的传热与传质分析(综述)

本文论述了分形介质的分形理论和数学基础,并简要综述了用分形理论和方法研究分形介质的传热与传质特性(如多孔介质的渗透率、热导率以及池核态沸腾换热)方面目前所取得的研究进展,最后扼要展望了用分形理论和方法进一步研究分形介质的传热与传质的可能的若干课题和方向。     

The method of lines solution of discrete ordinates method for radiative heat transfer in cylindrical enclosures

A radiation code based on method of lines solution of discrete ordinates method for radiative heat transfer in axisymmetric cylindrical enclosures containing absorbing-emitting medium was developed and tested for predictive accuracy by applying it to (i) test problems with black and grey walls (ii) a gas turbine combustor simulator enclosing a non-homogeneous absorbing-emitting medium and benchmarking its steady-state predictions against exact solutions and measurements. Comparisons show that it provides accurate solutions for radiative heat fluxes and can be used with confidence in conjunction with CFD codes based on the same approach.     

Conformal Invariance, Accelerating Universe and the Cosmological Constant Problem

We investigate a conformal invariant gravitational model which is taken to hold at early universe. The conformal invariance allows us to make a dynamical distinction between the two unit systems (or conformal frames) usually used in cosmology and elementary particle physics. In this model we argue that when the universe suffers phase transition, the resulting mass scale introduced by particle physics should have a variable contribution to vacuum energy density. This variation is controlled by the conformal factor which is taken as a dynamical field. We then deal with the cosmological consequences of this model. In particular, we shall show that there is an inationary phase at early times. At late times, on the other hand, it provides a mechanism which makes a large effective cosmological constant relax to a sufficiently small value. Moreover, we shall show that the conformal factor acts as a quintessence field that leads the universe to accelerate at late times.     

LES of turbulent heat transfer: proper convection numerical schemes for temperature transport

Large eddy simulations of two basic configurations (decay of isotropic turbulence, and the academic plane channel flow) with heat transfer have been performed comparing several convection numerical schemes, in order to discuss their ability to evaluate temperature fluctuations properly. Results are compared with the available incompressible heat transfer direct numerical simulation data. It is shown that the use of regularizing schemes (such as high order upwind type schemes) for the temperature transport equation in combination with centered schemes for momentum transport equation gives better results than the use of centred schemes for both equations. Copyright © 2004 John Wiley & Sons, Ltd.     

Dependence of the kinetics of the anionic polymerization of methyl methacrylate on the concentration in active centers

Studies on the anionic polymerization of methyl methacrylate in tetrahydrofuran and in the presence of sparteine have revealed a beneficial effect due to this additive, resulting in a decrease in the extent of termination. Better control of the definition of the polymers formed can thus be achieved in the presence of this additive. On the other hand, macromolecular engineering requires a range of active species concentrations lower than 10^?3 mol L^?1 and particularly the synthesis of polymers of high molar masses. For a better understanding of the mechanism of chain growth under such concentration conditions, the kinetics of polymerization have been investigated with a technique based on adiabatic calorimetry. Sparteine has been found to lack sufficient cation‐binding power to prevent the propagating enolate ion pairs from aggregating. The rate constant of propagation of nonaggregated species has been estimated, as well as the aggregation constant of equilibrium. For very low initiator concentrations, termination reactions have been shown to profoundly alter the control of the polymerization and to prevent a quantitative monomer conversion. Theoretical maximal conversions have been calculated from kinetic data and compare well with the experimental values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4964–4975, 2004     

Dynamic surface tension measurements of surfactant solutions using the maximum bubble pressure method – limits of applicability

One of the essential differences in the design of bubble pressure tensiometers consists in the geometry of the measuring capillaries. To reach extremely short adsorption times of milliseconds and below, the so-called deadtime of the capillaries must be of the order of some 10 ms. In particular, for concentrated surfactant solutions, such as micellar solutions, short deadtimes are needed to minimize the initial surfactant load of the generated bubbles. A theoretical model is derived and confirmed by experiments performed for a wide range of experimental conditions, mainly in respect to variations in deadtime and bubble volume.     

Addition–fragmentation chain transfer: Molecular weight distributions and retardation in the system methyl methacrylate/methyl α‐(bromomethyl)acrylate

A detailed investigation of addition–fragmentation chain transfer (AFCT) in the free‐radical polymerization of methyl methacrylate (MMA) in the presence of methyl α‐(bromomethyl)acrylate (MBMA) was carried out to elucidate mechanistic details with efficient macromonomer synthesis as an underlying goal. Advanced modeling techniques were used in connection with the experimental work. Curve fitting of simulated and experimental molecular weight distributions with respect to the rate coefficient for addition of propagating radicals to MBMA (k_add) over 60–120 °C resulted in E_add = 21.7 kJ mol^?1 and A_add = 2.18 × 10⁶ M^?1 s^?1 and a very weak temperature dependence of the chain‐transfer constant (E_add ≈ E_p). The rate coefficient for fragmentation of adduct radicals at 60 °C was estimated as k_f ≈ 39 s^?1 on the basis of experimental data of the MMA conversion and the concentration of 2‐carbomethoxy‐2‐propenyl end groups. The approach developed is generic and can be applied to any AFCT system in which copolymerization does not occur and in which the resulting unsaturated end groups do not undergo further reactions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2640–2650, 2004     

光学非球面二次曲面常数及顶点曲率的研究

受光学非球面制造过程中诸工艺参数的影响,能否保证非球面顶点曲率及二次曲面常数的精度是一个重要问题。基于二次曲面方程,推导出确定光学非球面二次曲面常数k以及顶点曲率半径r的一组算法,并在对一块口径为760mm×200mm标准非球面反射镜的实际测算中进行拟合,经过优化,拟合精度达到Δk=0.015,Δr=0.341mm,从而有效的控制了光学非球面制造过程中的顶点曲率及二次曲面常数的偏差。