Microstructure and optical properties of nitrogen-doped ZnO film

The nitrogen doping of ZnO film deposited by the magnetron sputtering method is subsequently realized by the hydrothermal synthesis method.The nitrogen-doped ZnO film is preferably(002) oriented.With the increase of hexamethylenetetramine(HMT) solution concentration,the average grain size of the film along the 002 direction almost immediately decreases and then monotonously increases,conversely,the lattice strain first increases and then decreases.The structural evolution of the film surface from compact and even to sparse and rough is attributed to the enhanced nitrogen doping content in the hydrothermal process.The transmission and photoluminescence properties of the film are closely related to grain size,lattice strain,and nitrogen-related defect arising from the enhanced nitrogen doping content with HMT concentration increasing.     

Preparation, structures and photoluminescent enhancement effect of PbWO4–TiO2 composite nanofilms

A novel route for preparing PbWO₄–TiO₂ nanofilms on a glass substrate is firstly proposed. The collodion is used as a dispersant and film-forming agent. The nanofilms are characterized through SEM, XRD, TG/DTA, PL and IR, respectively. The results of XRD indicate PbWO₄ particles with tetragonal scheelite structure and TiO₂ particles with Anatase phase, and SEM shows they are well dispersed in the substrate. Compared with nanoparticles, when TiO₂ nanoparticles are added in 5% ratio, the PL intensities at 395 nm of PbWO₄ nanofilms are enhanced obviously. IR spectrum reveals a large absorption band between 750 and 870 cm⁻¹, which is the W–O stretching vibration in WO₄ tetrahedron.     

纳米TiO2∶Zn薄膜电极紫外光电特性研究

采用sol-gel法制备了Zn2+掺杂的锐钛矿相纳米TiO2薄膜电极.通过光电流作用谱和电流-电位（I-U）曲线研〖WTBZ〗究了掺杂不同浓度Zn2+的TiO2薄膜电极的光电特性.由光电流作用谱可知，Zn2+的掺杂可显著影响薄膜电极的光电流大小，且掺杂的最佳浓度与薄膜晶粒尺度有关.在320nm单色光照射下，掺杂浓度（摩尔浓度）为0.1％的薄膜电极光电流最大，与未掺杂的本征薄膜电极相比增幅达40％.I-U曲线表明，光照下，随电极电位由正到负逐渐降低，不同掺杂浓度的TiO2薄膜电极中均出现了阳极电流向阴极电流转换的现象，且Zn2+掺杂浓度可影响电极阳极电流的初始电位.另外，无光照的暗态下，各薄膜在负电位区域观察到了相似的随电位降低而迅速增大的阴极暗电流.     

A voltage-controlled chaotic oscillator based on carbon nanotube field-effect transistor for low-power embedded systems

This paper presents a compact and low-power-based discrete-time chaotic oscillator based on a carbon nanotube field-effect transistor implemented using Wong and Deng＇s well-known model. The chaotic circuit is composed of a nonlinear circuit that creates an adjustable chaos map, two sample and hold cells for capture and delay functions, and a voltage shifter that works as a buffer and adjusts the output voltage for feedback. The operation of the chaotic circuit is verified with the SPICE software package, which uses a supply voltage of 0.9 V at a frequency of 20 kHz. The time series, frequency spectra, transitions in phase space, sensitivity with the initial condition diagrams, and bifurcation phenomena are presented. The main advantage of this circuit is that its chaotic signal can be generated while dissipating approximately 7.8 μW of power, making it suitable for embedded systems where many chaos-signal generators are required on a single chip.     

溶胶凝胶法制备圆柱形大孔二氧化硅反蛋白石结构晶体

利用溶胶凝胶法在不同直径的毛细管表面制备了圆柱形二氧化硅反蛋白石多孔结构.利用扫描电子显微镜表征了其形貌,发现胶体晶体的类(111)面结构整体为圆柱形,平行于毛细管表面.透射光谱结果表明,二氧化硅多孔结构在[111]方向具有典型的光子带隙效应,与布拉格理论相符合,有望应用到光通讯和传感领域.     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

Synthesis of multi-walled carbon nanotubes using CoMnMgO catalysts through catalytic chemical vapor deposition

The Co Mg O and Co Mn Mg O catalysts are prepared by a co-precipitation method and used as the catalysts for the synthesis of carbon nanotubes（CNTs） through the catalytic chemical vapor deposition（CCVD）. The effects of Mn addition on the carbon yield and structure are investigated. The catalysts are characterized by temperature programmed reduction（TPR） and X-ray diffraction（XRD） techniques, and the synthesized carbon materials are characterized by transmission electron microscopy（TEM） and thermo gravimetric analysis（TG）. TEM measurement indicates that the catalyst Co Mg O enclosed completely in the produced graphite layer results in the deactivation of the catalyst. TG results suggest that the Co Mn Mg O catalyst has a higher selectivity for CNTs than Co Mg O. Meanwhile, different diameters of CNTs are synthesized by Co Mn Mg O catalysts with various amounts of Co content, and the results show that the addition of Mn avoids forming the enclosed catalyst, prevents the formation of amorphous carbon, subsequently promotes the growth of CNTs, and the catalyst with decreased Co content is favorable for the synthesis of CNTs with a narrow diameter distribution.The Co Mn Mg O catalyst with 40% Co content has superior catalytic activity for the growth of carbon nanotubes.     

Effect of Surfactant Type and Concentration on Surfactant Migration,Surface Tension,and Adhesion of Latex Films

The effect of surfactant type and concentration on the migration behavior of surfactant in a latex film was investigated. Two types of surfactant, including an anionic (sodium lauryl sulfate, SLS) and a non-ionic (nonylphenol ethoxylate, average number of ethylene oxide units = 40, NP-40) surfactant, were used in an emulsion polymerization of methyl methacrylate butyl acrylate copolymer (MMA–BA). The total amount of surfactant was varied in three levels, i.e., 1.5, 3, and 4.5 wt%, and the surfactants were used both pure and in a mixture state. The surfactant migration to the film–air (F–A) and film–substrate (F–S) interfaces of the latex films was determined by using an attenuated total reflection-Fourier transform infrared (ATR-FTIR) method. In addition, the adhesion of the latex films to glass substrates was measured by a pull-off test. The results showed that the migration of anionic surfactant to the interfaces was greater than the non-ionic one. It was also found that the use of non-ionic surfactant along with anionic surfactant could decrease the migration of the anionic surfactant to the interfaces.     

厚二氧化硅光波导薄膜制备及其特性分析

以硅烷和氧化二氮作为反应气体，采用等离子体增强化学气相沉积(PECVD)技术，不使用掺杂，在单晶硅衬底上制备了用于平面光波导的二氧化硅薄膜。研究了薄膜折射率和淀积速率与工艺参量之间的关系，通过棱镜耦合仪、傅里叶变换红外光谱、原子力显微镜等测试手段，分析了薄膜的结构和光学特性。结果表明，实验能快速生长厚二氧化硅薄膜，薄膜表面平整，颗粒度均匀，同时薄膜具有折射率精确可控和红外透射性能好的特点，非常适合制作光波导器件。