混合判断矩阵排序方法研究

本文介绍了混合判断矩阵及完全一致性混合判断矩阵的概念，提出了混合判断矩阵排序的一种最小偏差法，并给出了其收敛性迭代算法，最后通过算例说明了方法的可行性。     

CdSe和ZnO量子点的拉曼光谱研究

本文介绍了用拉曼光谱研究CdSe和ZnO两种Ⅱ Ⅳ族量子点材料的结果,对拉曼峰进行了指认。观察到的光学声子峰位的移动被认为是由量子限制效应引起。     

The Analysis and Improving of the Microwave Exciter in the Lower Hybrid Wave System

When we carry out lower hybrid wave heating and current driving plasma experiment at tokamak, we need mega-watt order of microwave power. The microwave signal at frequency of 2450 MHz is generated by a microwave exciter. According to the experiment＇s demands, the microwave exciter must provide output power of 1.5～ 2. 5 W with stabilized frequency and amplitude tobe used as the klystron input. Being amplified by the klystron, the microwave signal is transmitted through the transmitting system to the antenna and is emitted into the HL-2A tokamak. So we can see that the microwave exciter＇s function is very important to the lower hybrid wave heating and current driving plasma experiment.     

Decreasing the Displacements of a Composite Saddle-Shaped Cable Roof

The structural possibilities of decreasing the compliance of a composite saddle-shaped cable roof having a compliant support contour are investigated. The use of a supporting contour consisting of cables joined together with tie-bars is considered as a structural method enabling one to decrease the compliance of the roof. Each cable of the support has its own initial flexure. The method is most efficient from the viewpoint of material consumption per unit of covered area relative to the increasing rigidity and prestress level of the cable net.The efficiency of the method was evaluated by a numerical experiment, which was carried out for a composite saddle-shaped cable roof 50 × 50 m in the plan. The roof was formed by two orthogonal cable groups joined with a compliant supporting contour. A hybrid composite cable based on a carbon-fiber-reinforced plastic, a glass-fiber-reinforced plastic, and steel was considered as a material for the cable net in combination with steel. The material consumption and the maximum vertical displacement of the cable net in relation to the initial geometrical characteristics of the supporting contour were obtained. A possibility of decreasing the maximum vertical displacements of the roof by 8% was established.     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

Zero Dissipative, Explicit Numerov-Type Methods for Second Order IVPs with Oscillating Solutions

New explicit, zero dissipative, hybrid Numerov type methods are presented in this paper. We derive these methods using an alternative which avoids the use of costly high accuracy interpolatory nodes. We only need the Taylor expansion at some internal points then. The method is of sixth algebraic order at a cost of seven stages per step while their phase lag order is fourteen. The zero dissipation condition is satisfied, so the methods possess an non empty interval of periodicity. Numerical results over some well known problems in physics and mechanics indicate the superiority of the new method.     

连续激光诱导Zn/InP掺杂过程中温度分布的解析计算

在实验的基础上，分析表面蒸发Zn的InP样品在连续激光诱导下掺杂Zn过程.在一维热传导问题的第三类边界条件下，给出激光辐照有限厚双层材料Zn/InP温度分布的一种直观简洁的解析形式. 关键词： 激光诱导掺杂 Zn/InP 温度分布     

Experimental investigation of time-dependent cavitation in an oscillatory squeeze film

The occurrence of time-dependent cavitation and tensile stress in an oscillatory oil squeeze film were investigated experimentally. The test apparatus was a simple thrust bearing consisting of two parallel circular plates separated by a thin viscous oil film. During the test, one plate was at rest while the other (transparent) oscillated in a direction normal to its surface. This test configuration was chosen to avoid the rotational motion and complicated geometry of a squeeze film journal bearing. The frequency of oscillation was in the range of 5 to 50 Hz and was controlled by an electro-magnetic exciter. The process of cavity formation and its subsequent development was recorded by a high-speed video camera. Concomitant pressure in the oil film was measured both within and without the cavitation region. It was found that both tensile stress and cavities existed in a squeeze film under certain working conditions.     

浮栅ROM器件辐射效应机理分析

分析了浮栅ROM器件的辐射效应机理，合理地解释了实验中观察到的现象.指出辐射产生的电子空穴对在器件中形成的氧化物陷阱电荷和界面陷阱电荷是导致存储单元及其外围电路出现错误的原因.浮栅ROM器件的中子、质子和⁶⁰Co γ辐射效应都是总剂量效应 . 关键词： FLASH ROM EEPROM 中子 质子 60Co γ')" href="#">⁶⁰Co γ 总剂量效应     

Synthesis and refractive‐index control of fluoropolymers by the polyaddition of bis(epoxide)s and triazine di(aryl ether)s

The polyaddition of fluorine‐containing bis(epoxide)s and fluorine‐containing triazine di(aryl ether)s were examined to give the corresponding fluorine‐containing poly(cyanurate)s. It was observed that the synthesized fluoropolymers had good thermal stabilities and good film‐forming properties. The glass transition temperatures (T_g's) and refractive‐indices (n_D's) of synthesized polymers were determined by differential scanning calorimetry and ellipsometry, respectively, and it was found that the values of T_g's and n_D's were supported by their fluorine containing ratios and skeletons. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4421–4429, 2007