Reactivity of a Ti–45.9Al–8Nb alloy in air at 700–900°C

A Ti–45.9Al–8Nb (at%) alloy with a lamellar structure (γ+α₂) was oxidised in air at 700, 800, 850 and 900°C in isothermal and thermal cycling conditions. The reaction progress was followed by thermogravimetric measurements. In isothermal conditions the oxidation kinetics followed approximately a parabolic rate law and the rate constants ranged from about 10^–12 kg² m^–4 s^–1 at 700°C to 10^–10 kg² m^–4 s^–1 at 900°C. The oxide scales were built of Al₂O₃ and TiO₂, the former being the main component of the outermost layer. The oxidation behaviour of Ti–45.9Al–8Nb was referred to a commercial titanium alloy, WT4 (Ti–6Al–1Mn), and selected oxidation-resistant alloys.     

Synthesis, morphology and random laser action of ZnO nanostructures

Three-dimensional (3-D) ZnO random-wall nanostructures and one-dimensional (1-D) ZnO nanorods were prepared on silicon substrates by a simple solid-vapour phase thermal sublimation technique. Optical pumped random lasing has been observed in the ZnO random-wall arrays with a threshold intensity of 0.38 MW/cm² in the emission wavelength from 380 to 395 nm. The optical gain was attributed to the closed-loop scattering and light amplification of the ZnO random-wall. The experimental result suggests that the morphology of nanostructure is the key factor to effect random lasing.     

Predicting the onset of DNA supercoiling using a non-linear hemitropic elastic rod

Elastic rod models provide a means to interpret single molecule DNA experiments as well as predict DNA behavior under physiological conditions. Here we use an elastic rod model to predict the stability boundary (critical torque vs. applied tension) for single molecule DNA experiments in which the molecule is subjected to applied tension and twist. We discuss the shortcomings of the usual isotropic rod model. We then derive a consistent non-linear material law from the general representation for a hemitropic (chiral) rod. Finally, we present results of a standard bifurcation analysis predicting the stability boundary. We find results from the non-linear hemitropic rod to match the data closely.     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

X-ray damage characterization in BaLiF3,KMgF3 and LiCaAlF6 complex fluorides

Two-inch sized KMgF₃,BaLiF₃ and LiCaAlF₆ (LiCAF) single crystals were grown by the Czochralski method under a CF₄ atmosphere. X-ray irradiation was used to carry out a comparative study of induced optical absorption phenomena and colour centre creation in the ultra-violet and visible spectral regions. The integral of the induced absorption spectra is significantly lower in LiCAF with respect to the other studied materials. It is found that the amplitude of the F-absorption band is suppressed more than a factor of 3 by Mg-doping. For Mg-doped crystals, the optimum doping concentration is about 0.2 mol% of Mg²⁺.     

The response of thermally and optically stimulated luminescence from Al2O3:C to high-energy heavy charged particles

The thermoluminescence (TL) and optically stimulated luminescence (OSL) response of Al₂O₃ dosimeters to high-energy heavy charged particles (HCP) has been studied using the heavy ion medical accelarator at Chiba, Japan. The samples were Al₂O₃ single-crystal chips, of the type usually known as TLD-500, and Luxel^TM dosimeters (Al₂O₃:C powder in plastic) from Landauer Inc. The samples were exposed to ⁴He (150 MeV/u), ¹²C (400 MeV/u), ²⁸Si (490 MeV/u) and ⁵⁶Fe (500 MeV/u) ions, with linear energy transfer values covering the range from 2.26 to 189 keV/μm in water and doses from 1 to 100 mGy (to water). A ⁹⁰Sr/⁹⁰Y beta source, calibrated against a ⁶⁰Co secondary standard, was used for calibration purposes. For OSL, we used both continuous-wave OSL measurements (CW-OSL, using green light stimulation at 525 nm) and pulsed OSL measurements (POSL, using 532 nm stimulation from a Nd:YAG Q-switched laser). The efficiencies (η_HCP,γ) of the different HCPs at producing OSL or TL were observed to depend not only upon the linear energy transfer (LET) of the HCP, but also upon the sample type (single crystal chip or Luxel^TM) and the luminescence method used to define the signal—i.e. TL, CW-OSL initial intensity, CW-OSL total area, or POSL. Observed changes in shape of the decay curve lead to potential methods for extracting LET information of unknown radiation fields. A discussion of the results is given, including the potential use of OSL from Al₂O₃ in the areas of space radiation dosimetry and radiation oncology.     

Luminescence properties of α-Al2O3 dosimetric crystals exposed to a high-current electron beam

The spectra of pulsed cathodoluminescence (PCL) and thermoluminescence (TL) in TLD-500 detectors, which were exposed to a strong beam from a pulsed electron accelerator, have been studied. Additional bands in the PCL spectrum and new peaks in the TL curves, which are due to impurity ions, have been revealed. Luminescence bands of F- and F⁺-centers cannot be used in the dosimetry of strong electron beams using TLD-500 detectors because of the saturation of dose dependence and the decrease in the TL yield. It is shown that high doses from these beams can be measured by recording TL in the luminescence band of impurity titanium ions.     

Dispersion Characteristics of Waveguide Arrays in Optical Spectrum Analyzers

Formulas for calculating the spectral characteristics of waveguide arrays, which are incorporated into waveguide spectrum analyzers based on planar waveguides, channel waveguides, and fiber optical waveguides, are derived taking into account the contribution of both the waveguide dispersion and the material dispersion to the dispersion factor. These formulas are used to study the dependence of the dispersion factor on the waveguide-system parameters for specific models of waveguide arrays. It is shown that consideration of contributions of the waveguide dispersion and material dispersion can affect profoundly the spectral characteristics of waveguide arrays.     

Measurement uncertainty of selenium determination in the reference material Seronorm Trace Elements Serum by hydride generation atomic fluorescence spectrometry

 An analytical result is not considered to be complete without a statement of the measurement uncertainty associated with it. Evaluation of measurement uncertainty is therefore an essential part of every determination. In the present study the measurement uncertainty of the result of determination of selenium in the reference material Seronorm Trace Elements Serum was studied. The combination of a digestion procedure using sulfuric acid, V₂O₅ in H₂SO₄ and hydrogen peroxide and the continuous flow approach of hydride generation atomic fluorescence spectrometry (HG-AFS) detection was used for selenium determination. The total uncertainty budget was calculated with the help of the GUM Workbench program, in which computations follow the rules of the ’ISO guide to the expression of uncertainty in measurement’. The major sources of uncertainty were found to be due to the recovery of the procedure, measurement of peak heights and the purity of Na₂SeO₃. A selenium mass fraction of 77.1±4.8 ng/g (with a coverage factor of 2.1, 95% probability) was determined, which is comparable with the recommended value of 80 ng/g. Received: 13 September 2002 Accepted: 23 December 2002 Acknowledgements We would like to thank Tinkara Buˇcar, B.Sc. for useful discussions and the IAEA Vienna, for financial support of the project 11553/RO. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to V. Stibilj     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.