Nanocrystalline ceramic films for efficient conversion of light into electricity

Transparent nanocrystalline films of oxide semiconductors such as TiO₂ and Fe₂O₃ have been prepared on a conducting glass support employing a sol-gel procedure. The films are composed of nanometer-sized particles sintered together to allow for percolative charge carrier transport. The internal surface of these films is very high, roughness factors of the order of 1000 being readily obtained. Electric polarization was applied for forward and reverse biasing of the films and the resulting optical changes have been analyzed to derive their flat band potential. Band gap excitation of such nanocrystalline semiconductors produces electron-hole pairs which migrate through the film to be collected as electric current. Steady state photolysis and time resolved laser techniques have been applied to scrutinize the mechanism of light induced charge separation within the nanostructure. When derivatized with a suitable chromophore, TiO₂ films give extraordinary efficiencies for the conversion of incident photons into electric current, exceeding 90% for certain transition metal complexes within the wavelength range of their absorption band. The underlying physical principles of these astonishing findings will be discussed. Exploiting this discovery, we have developed a new type of photovoltaic device whose overall light to electric energy conversion yield is 10% under simulated AM 1.5 solar radiation.     

Metal–Nitrosyl complexes as a source of new vasodilators: Strategies derived from systematic chemistry and nitrosyl ligand reactivity

A series of nitrosyl complexes of empirical formula K_n[M(CN)₅NO], where M = V, Cr, Mn and Co and n = 3, or M = Mo and n = 4, have been prepared which are notional analogues of the widely used vasodilator sodium nitroprusside. Their reactivity towards common nucleophiles (OH^?, NH₂R, NHR₂, HS^? and RS^?), acid and photolysis has been investigated to elucidate the desired properties required of new metal nitrosyls which may have some potential as new non-cyanide-based vasodilators.     

Species differences in the metabolism of arsenic compounds

Humans are exposed via air, water and food to a number of different arsenic compounds, the physical, chemical, and toxicological properties of which may vary considerably. In people eating much fish and shellfish the intake of organic arsenic compounds, mainly arsenobetaine, may exceed 1000 μg As per day, while the average daily intake of inorganic arsenic is in the order of 10–20 μg in most countries. Arsenobetaine, and most other arsenic compounds in food of marine origin, e.g. arsenocholine, trimethylarsine oxide and methylarsenic acids, are rapidly excreted in the urine and there seem to be only minor differences in metabolism between animal species. Trivalent inorganic arsenic (AsIII) is the main form of arsenic interacting with tissue constituents, due to its strong affinity for sulfhydryl groups. However, a substantial part of the absorbed AsIII is methylated in the body to less reactive metabolities, methylarsonic acid (MMA) and dimethylarsinic acid (DMA), which are rapidly excreted in the urine. All the different steps in the arsenic biotransformation in mammals have not yet been elucidated, but it seems likely that the methylation takes place mainly in the liver by transfer of methyl groups from S-adenosylmethionine to arsenic in its trivalent oxidation state. A substantial part of absorbed arsenate (AsV) is reduced to AsIII before being methylated in the liver. There are marked species differences in the methylation of inorganic arsenic. In most animal species DMA is the main metabolite. Compared with human subjects, very little MMA is produced. The marmoset monkey is the only species which has been shown unable to methylate inorganic arsenic. In contrast to other species, the rat shows a marked binding of DMA to the hemoglobin, which results in a low rate of urinary excretion of arsenic.     

Azine bridged silver coordination polymers: Powder X-ray diffraction route to crystal structure determination of silver benzotriazole

In continuation of our interest in solid-state structures of silver complexes of photographic importance, the structure for silver benzotriazole (AgBZT), has now been obtained. The preferred method for solving crystal structures is via single-crystal X-ray diffraction (XRD). However, for some materials, growing single crystals of appropriate size and quality is often difficult or even impossible. AgBZT is an example of such a silver complex with poor solubility. The usual routes to preparing single crystals using recrystallization from a cooperating solvent resulted in polycrystalline powder samples. We propose a crystal structure for AgBZT, solved from synchrotron X-ray powder diffraction data, using a direct-space Monte Carlo simulated annealing approach. AgBZT crystals are monoclinic, (P2₁/c), with unit cell dimensions, a=14.8052(3) Å, b=3.7498(4) Å, c=12.3495(12) Å, and β=114.200(6)°. The AgBZT complex is constructed from all three of the Benzotriazole (BZT) nitrogens bonding to a separate silver atom. As a consequence of this bonding mode, the structure is a highly cross-linked, coordination polymer.     

The Fundamental Experiments of Red Tide Chemical Forecast

Many food algae and red tide algae were cultivated in the f/2 medium, and the nitric oxide (NO) concentration of the medium and the cell density were determined. The experiments on algae were conducted when different concentrations of NO were added into the medium using two methods. The results show that low concentrations of NO were self-produced by marine algae during the exponential growth period and were about nmol/L level. But at the end of the period, i.e., 2 or 3 days before the cell density reaches the maximum, an NO peak appeared, with the NO concentration reaching 10 nmol/L. The NO threshold concentration exists according to the influence of exogenous NO on the marine phytoplankton growth. One type is the threshold concentration that can promote algae growth, and its value is between 10 and 1 nmol level, or even lower. The other type can inhibit the phytoplankton growth, which is about μmol level or higher. The results indicate that red tide algae are far more sensitive to NO than are food algae. The fundamental experimental outcome above may provide a new clue for red tide chemical forecast by inspecting the NO change.     

Effects of barium on the nonlinear electrical characteristics and dielectric properties of SnO2-based varistors

The effects of barium on electrical and dielectric properties of the SnO_2·Co_2O_3·Ta_2O_5 varistor system sintered at 1250℃ for 60min were investigated. It is found that barium significantly improves the nonlinear properties. The breakdown electrical field increases from 378.0 to 2834.5V/mm, relative dielectric constant (at 1kHz) falls from 1206 to 161 and the resistivity (at 1kHz) rises from 60.3 to 1146.5kΩ·cm with an increase of BaCO_3 concentration from 0mol% to 1.00mol%. The sample with 1.00mol% barium has the best nonlinear electrical property and the highest nonlinear coefficient (α=29.2). A modified defect barrier model is introduced to illustrate the grain-boundary barrier formation of barium-doped SnO_{2}-based varistors.     

Inorganic Sol-Gel Preparation of Medium Sized Microparticles of Li2TiO3 from TiCl4 as Tritium Breeding Material for Fusion Reactors

Microspheres of Li₂TiO₃ were fabricated by a classical, inorganic sol-gel process from commercially available TiCl₄. Elaborated process consists of the following main steps: (1) dissolving of TiCl₄ in concentrated aqueous HCl and addition of LiOH; (2) formation of sol emulsion in 2-ethylhexanol-1 containing the surfactant SPAN-80 (EH); (3) gelation of emulsion drops by extraction of water with partially dehydrated EH; (4) impregnation of gel to Li:Ti molar ratio MR = 2; (5) thermal treatment at 1200°C in order to receive chloride free product. This temperature can be significantly lowered (to 750°C) by dechlorination starting solution TiCl₄ by chemical treatment of the with nitric acid to form of nitrate-stabilized titania sols. Tritium release from sol-gel made Li₂TiO₃ microspheres were found very close to that observed for other traditional materials, however for the first sample process starts slightly earlier.     

Reactivity of a Ti–45.9Al–8Nb alloy in air at 700–900°C

A Ti–45.9Al–8Nb (at%) alloy with a lamellar structure (γ+α₂) was oxidised in air at 700, 800, 850 and 900°C in isothermal and thermal cycling conditions. The reaction progress was followed by thermogravimetric measurements. In isothermal conditions the oxidation kinetics followed approximately a parabolic rate law and the rate constants ranged from about 10^–12 kg² m^–4 s^–1 at 700°C to 10^–10 kg² m^–4 s^–1 at 900°C. The oxide scales were built of Al₂O₃ and TiO₂, the former being the main component of the outermost layer. The oxidation behaviour of Ti–45.9Al–8Nb was referred to a commercial titanium alloy, WT4 (Ti–6Al–1Mn), and selected oxidation-resistant alloys.     

Synthesis, morphology and random laser action of ZnO nanostructures

Three-dimensional (3-D) ZnO random-wall nanostructures and one-dimensional (1-D) ZnO nanorods were prepared on silicon substrates by a simple solid-vapour phase thermal sublimation technique. Optical pumped random lasing has been observed in the ZnO random-wall arrays with a threshold intensity of 0.38 MW/cm² in the emission wavelength from 380 to 395 nm. The optical gain was attributed to the closed-loop scattering and light amplification of the ZnO random-wall. The experimental result suggests that the morphology of nanostructure is the key factor to effect random lasing.     

Predicting the onset of DNA supercoiling using a non-linear hemitropic elastic rod

Elastic rod models provide a means to interpret single molecule DNA experiments as well as predict DNA behavior under physiological conditions. Here we use an elastic rod model to predict the stability boundary (critical torque vs. applied tension) for single molecule DNA experiments in which the molecule is subjected to applied tension and twist. We discuss the shortcomings of the usual isotropic rod model. We then derive a consistent non-linear material law from the general representation for a hemitropic (chiral) rod. Finally, we present results of a standard bifurcation analysis predicting the stability boundary. We find results from the non-linear hemitropic rod to match the data closely.