表面氧钝化碳化硅纳米团簇电子结构和光学性质的第一性原理研究

基于密度泛函理论(DFT)和广义梯度近似(GGA),对氧钝化条件下4H-SiC纳米团簇的电子结构和光学性质进行了研究。计算了不同直径的4H-SiC纳米球氧钝化后的能带结构、电子态密度和光学性质。团簇的尺度在0.4~0.9 nm之间,构建表面仅存在硅氧双键和表面仅存在碳氧双键的两种模型。研究表明硅氧双键和碳氧双键所引起的缺陷态位于原4H-SiC的价带和导带之间,并且缺陷态与价带顶的能量差随纳米团簇颗粒直径的增大而减小;缺陷态主要是由Si原子外层电子和氧原子外层电子轨道杂化引起的。同时,由于氧的存在,对碳化硅的结构产生一定的影响,这也是缺陷态形成的一个原因。另外,碳氧双键和硅氧双键钝化对4H-SiC纳米团簇的光学性质有着不同的影响。在表面仅存在C=O的情况下,4H-SiC纳米团簇表现出各向同性的性质。在表面仅存在Si=O的情况下,4H-SiC纳米团簇表现出各向异性的性质。     

Investigation of isothermal and no-isothermal oxidation of SiC powder using an analytic kinetic model

The oxidation of SiC powder has been investigated under non-isothermal and isothermal conditions. X-ray diffraction (XRD) analysis and transmission electron microscopy (TEM) were employed to investigate the morphological development during the oxidation. The results show that the major oxidation product was amorphous silica and the oxidation reaction was mainly diffusion-controlled. Based on limited experimental data, an analytic kinetic model, which expresses the oxidation weight gain as a function of time and temperature explicitly, has been used to predict the oxidation behavior of SiC powder. The comparison between experimental results and theoretical calculation shows that this new model works very well. The activation energy of non-isothermal and isothermal oxidation of SiC powder has been derived to be 226.5 kJ/mol and 187.5 kJ/mol, respectively.     

FP-LMTO method to calculate the structural,thermodynamic and optoelectronic properties of SixGe1−xC alloys

The structural and electronic properties of the ternary Si_xGe_1?xC alloys have been calculated using the full-potential linear muffin-tin-orbital (FP-LMTO) method based on density functional theory within both local density approximation (LDA) and generalised gradient approximation (GGA). The calculated equilibrium lattice constants and bulk moduli are compared with previous results. The concentration dependence of the electronic band structure and the direct and indirect band gaps are investigated. Using the approach of Zunger and co-workers, the microscopic origins of the band gap bowing are investigated also. Moreover, the refractive index and the optical dielectric constant for Si_xGe_1?xC are studied. The thermodynamic stability of the alloys of interest is investigated by means of the miscibility. This is the first quantitative theoretical prediction to investigate the effective masses, optical and thermodynamic properties for Si_xGe_1?xC alloy, and still awaits experimental confirmations.     

Influences of high-temperature annealing on atomic layer deposited Al2 O3/4H-SiC

High-temperature annealing of the atomic layer deposition (ALD) of Al2O3 films on 4H-SiC in O 2 atmosphere is studied with temperature ranging from 800℃ to 1000℃. It is observed that the surface morphology of Al2O3 films annealed at 800℃ and 900℃ is pretty good, while the surface of the sample annealed at 1000℃ becomes bumpy. Grazing incidence X-ray diffraction (GIXRD) measurements demonstrate that the as-grown films are amorphous and begin to crystallize at 900℃. Furthermore, C-V measurements exhibit improved interface characterization after annealing, especially for samples annealed at 900℃ and 1000℃. It is indicated that high-temperature annealing in O2 atmosphere can improve the interface of Al2O3 /SiC and annealing at 900℃ would be an optimum condition for surface morphology, dielectric quality, and interface states.     

First-principles study on the electronic transport properties of M/SiC Schottky junctions (M=Ag,Au and Pd)

In this work, we investigate the electronic transport properties of M/SiC Schottky junctions (M=Ag, Au and Pd). The results show that the band structures of hydrogenated zigzag SiC nanoribbons (ZSiCNRs) and hydrogenated armchair SiC nanoribbons (ASiCNRs) are almost unaffected by their width changes. When the hydrogenated 7-ASiCNR is directly connected to the Ag, Au and Pd electrode, the transmission spectra of three metal-semiconductor junctions show that the Fermi level of metal is pinned to a fixed position in the semiconductor band gap of hydrogenated 7-ASiCNR. The nearly same rectifying current-voltage characteristics are found in three metal-semiconductor junctions. The average rectification ratios of three M/SiC Schottky junctions are all in the neighborhood of 10⁶. In other word, the M/SiC Schottky junction has remarkable application prospect as the candidate for Schottky Diode.     

CrO2 (1 0 0) and TiO2 (1 0 0) film heteroepitaxy on a BaF2 (1 1 1)/Si (1 0 0) substrate

Multi-domained heteroepitaxial rutile-phase TiO₂ (1 0 0)-oriented films were grown on Si (1 0 0) substrates by using a 30-nm-thick BaF₂ (1 1 1) buffer layer at the TiO₂–Si interface. The 50 nm TiO₂ films were grown by electron cyclotron resonance oxygen plasma-assisted electron beam evaporation of a titanium source, and the growth temperature was varied from 300 to 600 °C. At an optimal temperature of 500 °C, X-ray diffraction measurements show that rutile phase TiO₂ films are produced. Pole figure analysis indicates that the TiO₂ layer follows the symmetry of the BaF₂ surface mesh, and consists of six (1 0 0)-oriented domains separated by 30° in-plane rotations about the TiO₂ [1 0 0] axis. The in-plane alignment between the TiO₂ and BaF₂ films is oriented as [0 0 1] TiO₂ || BaF₂ or [0 0 1] TiO₂ || BaF₂ . Rocking curve and STM analyses suggest that the TiO₂ films are more finely grained than the BaF₂ film. STM imaging also reveals that the TiO₂ surface has morphological features consistent with the BaF₂ surface mesh symmetry. One of the optimally grown TiO₂ (1 0 0) films was used to template a CrO₂ (1 0 0) film which was grown via chemical vapor deposition. Point contact Andreev reflection measurements indicate that the CrO₂ film was approximately 70% spin polarized.     

A modified polymethylsilane as the precursor for ceramic matrix composites

A novel SiC precursor, A-PMS, was synthesized through a reaction of polymethylsilane (PMS) with SbCl₃, where the Si-H in PMS reacts with Sb-Cl to form Si-Sb bond with HCl evaporated. A-PMS was used as a precursor to prepare C_f/SiC ceramic matrix composites (CMCs) via polymer infiltration and pyrolysis (PIP) process. It is evident that SbCl₃ plays a very important role in promoting chain crosslinking, transforming of the Si-Si into Si-C bonds and stabilizing PMS from very high oxidation trend of the active Si-H bonds. A-PMS keeps liquid at room temperature that is suitable for the infiltration in the absence of any solvent. A-PMS can be cured into a fully crosslinked structure at 320 °C that leads to a very high ceramic yield up to 91% and an Si/C ratio near 1.12 after pyrolysis. The resulted CMCs samples reached a density of 1.76 g cm⁻³ and a flexural strength of 381 MPa after only four infiltration-pyrolysis cycles.     

纳米SiC基光催化剂研究进展

Industrialization undoubtedly boosts economic development and improves the standard of living; however, it also leads to some serious problems, including the energy crisis, environmental pollution, and global warming. These problems are associated with or caused by the high carbon dioxide (CO₂) and sulfur dioxide (SO₂) emissions from the burning of fossil fuels such as coal, oil, and gas. Photocatalysis is considered one of the most promising technologies for eliminating these problems because of the possibility of converting CO₂ into hydrocarbon fuels and other valuable chemicals using solar energy, hydrogen (H₂) production from water (H₂O) electrolysis, and degradation of pollutants. Among the various photocatalysts, silicon carbide (SiC) has great potential in the fields of photocatalysis, photoelectrocatalysis, and electrocatalysis because of its good electrical properties and photoelectrochemistry. This review is divided into six sections: introduction, fundamentals of nanostructured SiC, synthesis methods for obtaining nanostructured SiC photocatalysts, strategies for improving the activity of nanostructured SiC photocatalysts, applications of nanostructured SiC photocatalysts, and conclusions and prospects. The fundamentals of nanostructured SiC include its physicochemical characteristics. It possesses a range of unique physical properties, such as extreme hardness, high mechanical stability at high temperatures, a low thermal expansion coefficient, wide bandgap, and superior thermal conductivity. It also possesses exceptional chemical characteristics, such as high oxidation and corrosion resistance. The synthesis methods for obtaining nanostructured SiC have been systematically summarized as follows: Template growth, sol-gel, organic precursor pyrolysis, solvothermal synthesis, arc discharge, carbon thermal reduction, and electrospinning. These synthesis methods require high temperatures, and the reaction mechanism involves SiC formation via the reaction between carbon and silicon oxide. In the section of the review involving the strategies for improving the activity of nanostructured SiC photocatalysts, seven strategies are discussed, viz., element doping, construction of Z-scheme (or S-scheme) systems, supported co-catalysts, visible photosensitization, construction of semiconductor heterojunctions, supported carbon materials, and construction of nanostructures. All of these strategies, except element doping and visible photosensitization, concentrate on enhancing the separation of holes and electrons, while suppressing their recombination, thus improving the photocatalytic performance of the nanostructured SiC photocatalysts. Regarding the element doping and visible photosensitization strategies, element doping can narrow the bandgap of SiC, which generates more holes and electrons to improve photocatalytic activity. On the other hand, the principle of visible photosensitization is that photo-induced electrons move from photosensitizers to the conduction band of SiC to participate in the reaction, thus enhancing the photocatalytic performance. In the section on the applications of nanostructured SiC, photocatalytic H₂ production, pollutant degradation, CO₂ reduction, photoelectrocatalytic, and electrocatalytic applications will be discussed. The mechanism of a photocatalytic reaction requires the SiC photocatalyst to produce photo-induced electrons and holes during irradiation, which participate in the photocatalytic reaction. For example, photo-induced electrons can transform protons into H₂, as well as CO₂ into methane, methanol, or formic acid. Furthermore, photo-induced holes can convert organic waste into H₂O and CO₂. For photoelectrocatalytic and electrocatalytic applications, SiC is used as a catalyst under high temperatures and highly acidic or basic environments because of its remarkable physicochemical characteristics, including low thermal expansion, superior thermal conductivity, and high oxidation and corrosion resistance. The last section of the review will reveal the major obstacles impeding the industrial application of nanostructured SiC photocatalysts, such as insufficient visible absorption, slow reaction kinetics, and hard fabrication, as well as provide some ideas on how to overcome these obstacles.      

Biomorphous SiC ceramics prepared from cork oak as precursor

Porous ceramic materials of SiC were synthesized from carbon matrices obtained via pyrolysis of natural cork as precursor. We propose a method for the fabrication of complex-shaped porous ceramic hardware consisting of separate parts prepared from natural cork. It is demonstrated that the thickness of the carbon-matrix walls can be increased through their impregnation with Bakelite phenolic glue solution followed by pyrolysis. This decreases the material’s porosity and can be used as a way to modify its mechanical and thermal characteristics. Both the carbon matrices (resulted from the pyrolysis step) and the resultant SiC ceramics are shown to be pseudomorphous to the structure of initial cork. Depending on the synthesis temperature, 3C-SiC, 6H-SiC, or a mixture of these polytypes, could be obtained. By varying the mass ratio of initial carbon and silicon components, stoichiometric SiC or SiC:С:Si, SiC:С, and SiC:Si ceramics could be produced. The structure, as well as chemical and phase composition of the prepared materials were studied by means of Raman spectroscopy and scanning electron microscopy.