Cavitation mechanism in cyanobacterial growth inhibition by ultrasonic irradiation

To prevent cyanobacterial bloom in eutrophic water by ultrasonic method, ultrasonic irradiations with different parameters were tested to inhibit Spirulina platensis from growth. The experimental result based on cyanobacterial growth, chlorophyll a and photosynthetic activity showed that, the ultrasonic irradiation inhibited cyanobacterial proliferation effectively, furthermore the inhibition effectiveness increased in the order: 200 kHz>1.7 MHz>20 kHz and became saturated with the increased power. The inhibition mechanism can be mainly attributed to the mechanical damage to the cell structures caused by ultrasonic cavitation, which was confirmed by light microscopy and differential interference microscopy. The optimal frequency of 200 kHz in cavition and sonochemistry was also most effective in cyanobacterial growth inhibition. The higher frequency of 1.7 MHz is weaker than 20 kHz in cavitation, but has more effective inhibition because it is nearer to the resonance frequency of gas vesicle. The inhibition saturation with ultrasonic power was due to the ultrasonic attenuation induced by the acoustic shielding of bubbles enclosing the radiate surface of transducer.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

30J能量驱动类镍银X光激光的理论研究

 在1.2×10¹³W·cm^－2低功率密度下，对基频激光预主短脉冲驱动类镍银X光激光机理进行了数值模拟和理论分析。证实了在靶长23 mm范围内X光激光都能获得有效放大，取得了和实验相符合的结果。考虑了单柱面镜线聚焦沿靶长度方向功率密度的非均匀性对X光激光放大的影响，采用弯曲靶能有效克服折射以及单柱面镜线聚焦功率密度非均匀带来的不利影响。理论模拟给出的类镍银X光激光的出光下限泵浦功率密度也与实验符合得很好。理论模拟还表明，采用1%左右的预脉冲强度并对预主脉冲时间间隔进行优化，X光激光的输出能量和能量转换效率将获得大幅度提高。     

聚焦慢速高荷态重离子束微束斑X射线源

利用电子束离子源(EBIS)或者电子束离子陷阱(EBIT)产生的慢速高电荷态重离子束轰击金属靶面,离子束与靶面作用并复合辐射特征X射线;并将高荷态离子束采用离子光学系统会聚为微细束后再与靶面作用,能够辐射出微米甚至亚微米级、纳米级的微束斑X射线.本文介绍这一新型微束斑X射线源的结构、机理及其特性等.     

介质靶表面的充电效应对等离子体浸没离子注入过程中鞘层特性的影响

针对等离子体浸没离子注入技术在绝缘体表面制备硅薄膜工艺，采用一维脉冲鞘层模型描述介质靶表面的充电效应对鞘层厚度、注入剂量及靶表面电位等物理量的影响.数值模拟结果表明：随着等离子体密度的增高，表面的充电效应将导致鞘层厚度变薄、表面电位下降以及注入剂量增加，而介质的厚度对鞘层特性的影响则相对较小. 关键词： 等离子体浸没离子注入 脉冲鞘层 绝缘介质 充电效应     

强流束晕-混沌的外部磁场开关控制

研究了强流离子束在周期聚焦磁场通道中束晕-混沌的外部磁场开关参数控制方法. 将该方法应用在多粒子模型中，实现了对5种不同初始分布质子束的束晕-混沌的有效控制，得到了消除束晕及其再生现象的理想结果.在强流加速器系统中，由于外部磁场是可测和可调 的物理量，因此该控制方法有利于实验研究，可为强流质子加速器中周期聚焦磁场的设计和实验提供参考. 关键词： 强流离子束 周期聚焦磁场通道 束晕_混沌 混沌控制 开 关控制     

离子束增强沉积VO2多晶薄膜的温度系数

用改进的离子束增强沉积方法和恰当的退火从V2O5粉末直接制备了VO2多晶薄膜.实验测试表明，薄膜的取向单一、相变特性显著、结构致密、界面结合牢固、工艺性能良好，薄膜的电阻温度系数（TCR）最高可达4.23%/K.从成膜机理出发，较详细地讨论了离子束增强沉积 VO2多晶薄膜的TCR高于VOx薄膜的TCR的原因.分析认为，单一取向的VO2结构使薄膜晶粒具有较高的电导激活能，致密的薄膜结构减少了氧空位和晶界宽度，使离子束增强沉积 VO2多晶薄膜结构比其他方法制备的VOx薄膜更接近于单晶VO2是其具有高TCR的原 关键词： VO2多晶薄膜 离子束增强沉积 热电阻温度系数     

晶格失配对异质外延超薄膜生长中成核特性的影响

利用动力学蒙特卡罗方法模拟了异质外延超薄膜生长中的成核过程.研究了薄膜与衬底的晶格失配对超薄膜生长中成核密度、平均核尺寸、标度关系及生长模式的影响.结果发现产生压（张）应变的晶格负（正）失配使生长过程更早（迟）从成核区进入过渡区，失配越大，这一效应越明显.在相同的沉积条件下，负失配导致超薄膜形成较低的成核密度与较大的平均核尺寸，而正失配则相反.成核密度满足标度关系Ns≈(F/D)χ，随着失配度从-0.04增加到0.02，标度系数χ从0.37逐渐减小到0.33，对应超薄膜生长过程从包含二聚体扩散模式转变到无 关键词： 薄膜生长 成核 晶格失配 蒙特卡罗模拟     

强流离子束离子径向密度分布的模拟研究

对初始分布为K-V分布的离子束进行模拟研究.除观察到存在束晕现象外，还发现离子束在通 道内运行过程中，离子沿径向密度分布发生了变化. 通过延迟反馈控制，不仅可以消除束晕 ，而且只要控制参数适当，也可以使束中心部分呈均匀分布状态. 关键词： 强流离子束 束晕 填充因子 离子密度分布     

稀土粉末Eu∶Y_2O_3的自由感应衰减量子拍

稀土固体是重要的激光和光电子材料。目前 ,由于以宽带信号和太赫兹比特数据传输率为特征的信息技术的发展 ,稀土固体材料的相干瞬态动力学过程成为宽带与高速信息光子学的基本物理问题之一。研究了室温下稀土粉末样品Eu3+ ∶Y2 O3自由感应衰减的相干瞬态光谱 ,这有助于理解有效的光吸收动力学、激发态弛豫、相干能量传递和超短光脉冲在稀土固体中的传播。用一对紫外飞秒相干光脉冲作用于稀土粉末样品Eu3+ ∶Y2 O3,然后监测物质激发态的布居数随两个激发脉冲之间的延时的变化 ,测量到其自由感应衰减量子拍 (FID) ,从拍频周期分析确定了其能级精细结构 ,能级的退相时间长达皮秒量级。理论分析和实验结果符合得很好。对稀土离子的量子干涉的研究 ,表明其在受激受控光放大方面具有潜在的应用前景