Molar excess heat capacities and volumes for mixtures of alkanoates with cyclohexane at 25°C

Molar excess volumes V ^E at 25°C have been determined by vibrating-tube densimetry, as a function of mole fraction x for different series of an alkanoate (H _2m+1 C _m COOC _n H _2n+1 )+cyclohexane. Three types of alkanoates were investigated, i.e., methanoates (m=0, with n=3 and 4), ethanoates (m=1, with n=2, 3, and 4) and propanoates (m=2, with n=1, 2, and 3). In addition, a Picker flow calorimeter was used to obtain molar excess heat capacities C _p ^E at constant pressure at the same temperature. V ^E is positive for all systems and rather symmetric, with V ^E (x=0.5) amounting to almost identical values in a series of mixtures containing an alkanoate isomer of same formula (say C₄H₈O₂, C₅H₁₀O₂, or C₆H₁₂O₂). The composition dependence of C _p ^E is rather unusual in that two more or less marked minima are observed for most of the mixtures, especially when the alkanoate is a methanoate or an ethanoate. These results are discussed in terms of possible changes in conformation of both the ester and cyclohexane.     

Thermal analysis of low alloy Cr-Mo steel

The paper deals with results of thermal analysis of low-alloyed chromium-molybdenum steel. The methods of analysis were dilatometry, differential thermal analysis (DTA) and differential scanning calorimetry (DSC). The Ac₁ and Ac₃ temperatures of the steel samples measured by dilatometry and DTA during the heating period were in good agreement. Generated by cooling a martensitic structure first became apparent at 503 K. Tempering of the as-quenched samples showed the presence of the second tempering stage in the region between 473 and 573 K. At that stage heat capacity decreased from 0.48 to 0.32 J g^-1 K^-1, as a result of conversion of transition carbide due to heat consumption. After normalization of the as-quenched samples the heat capacity values were restored to between 0.42 and 0.47 J g^-1 K^-1 in the temperature range from 373 to 673 K. This revised version was published online in August 2006 with corrections to the Cover Date.     

Characterization of quasi-one-dimensional S=1/2 Heisenberg antiferromagnets Sr2Cu(PO4)2 and Ba2Cu(PO4)2 with magnetic susceptibility, specific heat, and thermal analysis

Properties of Sr₂Cu(PO₄)₂ and Ba₂Cu(PO₄)₂ having [Cu(PO₄)₂]_∞ linear chains in their structures with Cu-O-P-O-Cu linkages were studied by magnetic susceptibility (T=2-400 K, H=100 Oe) and specific heat measurements (T=0.45-21 K). Magnetic susceptibility versus temperature curves, χ(T), showed broad maxima at T_M=92 K for Sr₂Cu(PO₄)₂ and T_M=82 K for Ba₂Cu(PO₄)₂ characteristic of quasi-one-dimensional systems. The χ(T) data were excellently fitted by the spin susceptibility curve for the uniform S=1/2 chain (plus temperature-independent and Curie-Weiss terms) with g=2.153(4) and J/k_B=143.6(2) K for Sr₂Cu(PO₄)₂ and g=2.073(4) and J/k_B=132.16(9) K for Ba₂Cu(PO₄)₂ (Hamiltonian H=JΣS_iS_i+1). The similar J/k_B values were obtained from the specific heat data. No anomaly was observed on the specific heat from 0.45 to 21 K for both compounds indicating that the temperatures of long-range magnetic ordering, T_N, were below 0.45 K. Sr₂Cu(PO₄)₂ and Ba₂Cu(PO₄)₂ are an excellent physical realization of the S=1/2 linear chain Heisenberg antiferromagnet with k_BT_N/J<0.34% together with Sr₂CuO₃ (k_BT_N/J≈0.25%) and γ-LiV₂O₅ (k_BT_N/J<0.16%). Sr₂Cu(PO₄)₂ and Ba₂Cu(PO₄)₂ were stable in air up to 1280 and 1150 K, respectively.     

Thermal requirements to obtain calcined and frits of ulexite

Ulexite has a substantial amount of hydration water, which allows using calcination methods to increase the B₂O₃ content from 42.97 to 66.69%, due to the loss of 35.54% of its weight, corresponding to its hydration water.In this study, determinations of changes in the heat content at each temperature were made using an isoperibol calorimeter. The mean specific heat was calculated from these values. The reaction enthalpy was also determined by DTA methods.The sample used in the experiments contains 39.04% B₂O₃. The temperature was between 80 and 1000 °C. Curves of weight loss and enthalpy changes are presented and analysed.The results have industrial application in order to determine the thermal requirements for calcining ulexite at different temperatures, as well as its complete dehydration.     

Characterization of the Converging Jet Region in a Triple Torch Plasma Reactor

Enthalpy probe measurements were taken of the converging plasma plume in a triple torch plasma reactor and related to substrate heat flux measurements. Results show excellent entrainment of process gases injected into the converging plasma plume by way of the central injection probe. At lower pressures (40 kPa), the plasma volume is equivalent to at least a 3 cm diameter, 4 cm long cylinder, with relatively uniform temperature, velocity, and substrate heat flux profiles when compared to a typical dc arc jet. Converging plasma plume size, substrate heat flux, and enthalpy profiles are also shown to be a strong function of applied system power. Substrate heat flux measurements show smaller radial gradients than enthalpy probe measurements, because of the high radial velocity component of gases above the substrate boundary layer. Enthalpy probe measurements were also conducted for diamond deposition conditions and approximate temperature and velocity profiles obtained. Problems with the uniform gas mixture assumption prohibited more accurate measurements. Reproducibility of enthalpy measurement results was shown with an average standard deviation of 11.8% for the velocity and 7.6% for the temperature measurements.     

Reversible Melting of Semi-Crystalline Polymers 2. Annealing Near to the Melting Point

Annealing experiments have been carried out at a few degrees below the melting point of different polyethylenes (LDPE, LLDPE, HDPE), of polypropylene (PP) and of Nylon-6. The heat capacities decrease during the annealing, within a 2-4 min time scale, to a lower value which corresponds to the extrapolated heat capacity values obtained for the cooling cycle when the polymer is cooled from the melt. Heat capacities in the heating cycle following the cooling cycle of PP, Nylon-6 and HDPE have the same value as during the cooling section. This is not the case for LDPE and LLDPE. Exothermic total heat flow in the cooling section following the annealing indicates that the crystallisation takes place during the cooling rather than during the annealing period. The total melting enthalpy measured before and after the annealing cycle is the same. The reversing heat flow shows an excellent fit to the change of the crystallinity measured by small angle scattering of synchrotron radiation during a heating cycle at temperatures below the melting peak. A coupled thermodynamic interaction of the crystalline and the amorphous phases is concluded from this study. This kind of interaction is possible at the lateral end of polymeric chains incorporated into the crystalline phase. This is an indication of the portion of tie molecules in the system, i.e. the portion of fringed micelle type of crystalline morphology with respect to that of folded chain lamellae. This revised version was published online in July 2006 with corrections to the Cover Date.     

Specific heat and neutron diffraction study on quaternary sulfides BaNd2CoS5 and BaNd2ZnS5

Magnetic and electrical properties are investigated for quaternary neodymium sulfides BaNd₂TS₅ (T=Co, Zn) through the specific heat, neutron diffraction, and electrical conductivity measurements. Their electrical conductivities show semiconductive behavior, which follows the Arrhenius temperature dependence with the activation energy of E_a=1.46 eV for BaNd₂ZnS₅ and E_a=1.19 eV for BaNd₂CoS₅. The specific heat of BaNd₂ZnS₅ has a λ-type anomaly at 2.8 K due to the antiferromagnetic ordering of the Nd³⁺ moments and a Schottky-type anomaly at around 60 K, which results from the crystal field splitting of the ⁴I_9/2 ground state of the Nd³⁺ ion. The specific heat of BaNd₂CoS₅ shows two λ-type anomalies at 5.7 K due to the antiferromagnetic ordering of Nd³⁺ and at 58 K due to the antiferromagnetic ordering of Co²⁺. The latter overlaps with the Schottky-type anomaly due to the crystal field splitting of the Nd³⁺ ion. Neutron diffraction measurements for BaNd₂CoS₅ show that a magnetic arrangement of the Co²⁺ moments has a collinear antiferromagnetic structure, while that of the Nd³⁺ moments has a noncollinear one.     

Excess heat capacities of ternary systems containing chlorobenzene or chloronaphthalene

Densities and heat capacities of ternary systems were determined at 25°C. The ternary systems consisted of: a polar molecule (component 1) + a mixture of alkanes (components 2 and 3) of different sizes and shapes. Five such systems were studied: chlorobenzene + cyclohexane + n-heptane; chlrobenzene + cyclohexane + n-hexadecane; chlorobenze + cyclohexane + isooctane; chlorobenzene + isooctane + n-heptane; 1-chloronaphthalene + isooctane + n-heptane. The excess molar volumes and heat capacities were obtained along dilution lines by component 1 (chlorobenzene or 1-chloronaphthalene) of mixtures of components 2 and 3 (at fixed component 2 mole fraction X₂). Unexpectedly the excess heat capacities C _p1(23) ^E of the pseudo-binaries {1+(2+3)} do not always fall between the two (limiting) curves of C _p12 ^E and C _p13 ^E corresponding to the two binaries {1+2} and {1+3}. Instead, especially for {chlorobenzene + cyclohexane + an n-alkane} the C _p1(23) ^E curves are displaced toward less negative values, even beyond the limiting values corresponding to the binaries. This correlates semi-quantitatively with the negative C _p23 ^E of the binary {2+3}.Presented at the Symposium, 76^th CSC Congress, Sherbrooke, Quebec, May 30-June 3, 1993, honoring Professor Donald Patterson on the occasion of his 65^th birthday.     

迎头色谱程序升温脱附快速测定吸附热新方法

在Ｐｏｌａｎｙｉ吸附势理论基础上，结合程序升温脱附曲线的测定，建立了一个快速测定吸附热的新方法，详细讨论了该方法的原理，通过微机采样和数据处理，测定一条吸附热与覆盖度的曲线仅需１ｈ左右。     

调制式DSC在高聚物研究中的应用

综述了一种新的热分析技术－－调制式差示扫描量热示（Modulated Differentail Scanning Calorimetry）。对其工作原理，优点及在高聚物研究中的应用作了简介。