基于CSCW的协同编著系统的设计

讨论了计算机支持的协同工作(CSCW)的主要技术，其中重点讨论了协同编著系统设计中的并发控制技术，指出了其与传统的并发控制技术的区别。根据CSCW的基本原理设计出了一个基于Browse／Server结构的协同编著系统的系统模型。该系统模型比传统的模型更加方便了用户之间通过Internet的浏览器进行协作。     

On the structure of the optimal server control for fluid networks

This paper derives the optimal trajectories in a general fluid network with server control. The stationary optimal policy in the complete state space is constructed. The optimal policy is constant on polyhedral convex cones. An algorithm is derived that computes these cones and the optimal policy. Generalized Klimov indices are introduced, they are used for characterizing myopic and time-uniformly optimal policies.Received: November 2004 / Revised: February 2005The research of this author has been supported by the project ‘‘Stochastic Networks’’ of the Netherlands Organisation for Scientific Research NWO.     

重新初始化的LS方法跟踪二维可压缩多介质流界面运动

 用非耦合求解方法计算Level Set函数方程与流体力学方程组，应用重新初始化的Level Set函数确保距离函数性质，流体力学方程组采用二阶精度多介质流波传播差分格式计算，重新初始化方程采用五阶WENO格式计算。并给出了二维可压缩多介质流界面运动的计算结果。     

In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.     

Robust Speed Control of a Low Damped Electromechanical System Based on CRONE Control: Application to a Four Mass Experimental Test Bench

Robust speed control of a low damped electromechanical system with backlash is studied, controlled load angular speed being not measured. The proposed control strategy combines a Luenberger observer (load angular speed and load torque disturbance estimations) and a robust CRONE controller. The observer provides estimation of the load angular speed and of the disturbance torque applied on the load. Through the computation of only three independent parameters (as many as a PID controller), the CRONE controller permits to ensure the robust speed control of the load in spite of plant parametric variations and speed observation errors. The proposed control strategy is applied to a four mass experimental test bench.     

Classical in-plane negative magnetoresistance and quantum positive magnetoresistance in undoped InSb thin films on GaAs (1 0 0) substrates

Magnetoresistance (MR) effects have been investigated in perpendicular and parallel magnetic fields at 300, 80 K and liquid He temperatures for undoped InSb thin films 0.1–2.3 μm thick grown on GaAs(1 0 0) substrates by MBE. At high temperatures, the intrinsic carriers show the parabolic negative MR observable only in magnetic fields parallel to the film. The skipping-orbit effect due to surface boundary scattering in the classical orbits in the plane vertical to the film has been argued to be responsible for the negative MR. At low temperatures (T=80 K), the transport is dominated by the two-dimensional (2D) electrons in the accumulation layers at the InSb/GaAs(1 0 0) hetero interface; MR is positive and shows a logarithmic increase with anisotropy between parallel and perpendicular field orientation, arising from the 2D weak anti-localization (WAL) that reflects the interplay between the spin-Zeeman effect and strong spin–orbit interaction caused by the asymmetric potential at the interface (Rashba term). The zero-field spin splitting energy of Δ₀13 meV, the electron effective mass of m^*0.10m₀ seven times of the band edge mass in bulk InSb and the effective g-factor of |g^*|15 in the accumulation layer have been inferred from fits of MR for the 0.1 μm thick film to the 2D WL theory.     

Preparation and characterization of acrylic‐based black particles of poly(methyl methacrylate‐co‐ethylene glycol dimethacrylate) by dispersion polymerization for electrophoretic displays

Ultrafine black particles, ranging in diameter from 1 to 3 μm, were prepared by dispersion polymerization in a methanol/water mixture with vinyl monomers, nonpolymerizable Sudan black B dyes, and fluorescein isothiocyanate labeled charge control additives. Both the ratio of the methanol to the water dispersion medium and the polymeric stabilizer concentration had significant effects on the particle size. The important role of the stabilizer concentration lay in the particle formation step, during which it determined the particle stability and final particle size. These could affect the extent of the aggregation of nuclei by changing the adsorption rate of the stabilizer and the viscosity of the dispersion medium, resulting in smaller particles. The fluorescent‐labeled charge control additives strongly affected the electrophoretic mobility. A small concentration of fluorescent‐labeled charge control additives increased the electrophoretic mobility. However, a further addition reduced the electrophoretic mobility of the polymer particles. The concentration dependence of the fluorescent‐labeled charge control additives on the deposition behavior in the polymer particles was successfully imaged and thereafter quantified by image analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5608–5616, 2004     

Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

硬盘磁头-碟界面润滑剂失效机理及添加剂X-1P的性能研究

采用热重分析 (TGA)、傅立叶红外光分析 (FTIR)和磁头起飞降落 (CSS)等试验方法 ,研究了硬盘磁头 碟界面润滑层PFPE的失效机理以及添加剂X 1P在磁头 碟界面润滑剂中的作用 .研究结果表明 ,高温条件下磁头材料Al2 O3 会诱导磁头 碟界面润滑剂PFPE发生歧化降解 ,造成磁头 碟界面润滑层失效 ;添加剂X 1P因其特殊的分子结构和化学性能 ,可作为一种有效稳定剂添加到磁头 碟润滑剂PFPE中 ,减弱磁头材料Al2 O3 作为催化反应中心的催化反应活性 ,减缓磁头 碟界面润滑剂PFPE的高温歧化降解 ,改善磁头 碟界面的CSS性能