发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

ZnO-Si不同退火条件对生长ZnSe薄膜的影响

研究了作为缓冲层的ZnO薄膜在不同的退火时间、退火温度下退火对Si衬底上生长ZnSe膜质量的影响。当溅射有ZnO膜的Si(111)衬底的退火条件变化时，从X射线衍射谱（XRD）和光致发光谱（PL）中可见，ZnSe(111)膜的晶体质量有较大的变化。变温的PL谱表明，Si衬底上生长的具有ZnO缓冲层的ZnSe膜的近带边发射峰起源于自由激子发射。     

电场的增强作用对介质膜光栅损伤形貌的影响

研究了电场在介质膜光栅结构中的增强效应对其抗激光损伤阈值的影响.使用傅里叶模式方法计算了电场在介质膜光栅浮雕结构内的分布.数值分析表明：电场在介质膜光栅中增强的最大值为入射光的2倍,其最大的位置出现在相对于入射光对面的光栅槽侧壁。实验测试介质膜光栅样品在1 064 nm和12 ns, 51.2°和TE偏振光入射时,其抗激光损伤阈值为6.61 J/cm2.对损伤形貌进行扫描电镜精确分析,发现介质膜光栅的初始损伤产生于电场在介质膜光栅内增强最大的位置处.     

HL-1装置脱离等离子体及边界等离子体杂质辐射的观测

首次用三道光纤探测器,伸入HL-1装置内真空室,采集活动石墨孔栏处等离子体光信号,用22m石英长光纤传输光信号至控制室进行观测。通过边界等离子体H_α和杂质辐射的时空分布,初步探讨了HL-1装置的脱离等离子体。     

Controlled decoherence of three-level rf-SQUID qubit with asymmetric potential

A scheme is proposed to controll the decoherence of three-level rf-SQUID qubit with asymmetric potential by designing an external electric circuit for superconductive flux qubit. The results show that it may not only raise the gate speed but also extend decoherence time for a three-level structure.     

Increase in the Intracellular Bulk Water Content in the Early Phase of Cell Death of Keratinocytes,Corneoptosis, as Revealed by 65 GHz Near-Field CMOS Dielectric Sensor

While bulk water and hydration water coexist in cells to support the expression of biological macromolecules, how the dynamics of water molecules, which have long been only a minor role in molecular biology research, relate to changes in cellular states such as cell death has hardly been explored so far due to the lack of evaluation techniques. In this study, we developed a high-precision measurement system that can discriminate bulk water content changes of ±0.02% (0.2 mg/cm³) with single-cell-level spatial resolution based on a near-field CMOS dielectric sensor operating at 65 GHz. We applied this system to evaluate the temporal changes in the bulk water content during the cell death process of keratinocytes, called corneoptosis, using isolated SG1 (first layer of stratum granulosum) cells in vitro. A significant irreversible increase in the bulk water content was observed approximately 1 h before membrane disruption during corneoptosis, which starts with cytoplasmic high Ca²⁺ signal. These findings suggest that the calcium flux may have a role in triggering the increase in the bulk water content in SG1 cells. Thus, our near-field CMOS dielectric sensor provides a valuable tool to dissect the involvement of water molecules in the various events that occur in the cell.     

Analysis of the generation mechanism of the S-shaped J—V curves of MoS2/Si-based solar cells

Amorphous-microcrystalline MoS$_{2}$ thin films are fabricated using the sol-gel method to produce MoS$_{2}$/Si-based solar cells. The generation mechanisms of the S-shaped current density-voltage ($J$-$V$) curves of the solar cells are analyzed. To improve the performance of the solar cells and address the problem of the S-shaped $J$-$V$ curve, a MoS$_{2}$ film and a p$^+$ layer are introduced into the front and back interfaces of the solar cell, respectively, which leads to the formation of a p-n junction between the p-Si and the MoS$_{2}$ film as well as ohmic contacts between the MoS$_{2}$ film and the ITO, improving the S-shaped $J$-$V$ curve. As a result of the high doping characteristics and the high work function of the p$^+$ layer, a high-low junction is formed between the p$^+$ and p layers along with ohmic contacts between the p$^+$ layer and the Ag electrode. Consequently, the S-shaped $J$-$V$ curve is eliminated, and a significantly higher current density is achieved at a high voltage. The device exhibits ideal p-n junction rectification characteristics and achieves a high power-conversion efficiency (CE) of 7.55%. The findings of this study may improve the application of MoS$_{2}$ thin films in silicon-based solar cells, which are expected to be widely used in various silicon-based electronic and optical devices.     

Influences of nanoparticles and chain length on thermodynamic and electrical behavior of fluorine liquid crystals

Hydrogen-bonded polar nematic liquid crystal series with the general formula nOBAF (n = 7—12) is studied. The mesomorphic characterization is demonstrated through differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The complexes with short alkyl chains (n=7, 8) present a wide nematic range and monotropic smectic F mesophase, whereas the longer alkyl chain (n=10—12) analogues show high melting and low clearing mesomorphic liquid crystals. The thermal range of the mesophase and the birefringence increase with chain length decreasing. Furthermore, the effect of the nanoparticles (LiNbO₃) on the thermal and the electrical behavior of 8OBAF are investigated. The presence of LiNbO₃ nanoparticles increases the conductivity and reduces the resistivity of the complex.     

Electrical, dielectric and surface wetting properties of multi-walled carbon nanotubes/nylon-6 nanocomposites

This paper reports that the multi-walled carbon nanotubes(MWCNT)/nylon-6 (PA6) nanocomposites with different MWCNT loadingshave been prepared by a simple melt-compounding method. Theelectrical, dielectric, and surface wetting properties of theCNT/PA6 composites have been studied. The temperature dependence ofthe conductivity of the CNT/PA6 composite with 10.0 wt{\%} CNTloading ($\sigma _{\rm RT} \sim 10^{-4}$ S/cm) are measured, andafterwards a charge-energy-limited tunnelling model (ln $\sigma (T)\sim T^{-1/2})$ is found. With increasing CNT weight percentage from0.0 to 10.0 wt%, the dielectric constant of the CNT/PA6composites enhances and the dielectric loss tangent increases twoorders of magnitude. In addition, water contact angles of theCNT/PA6 composites increase and the composites with CNT loadinglarger than 2.0 wt%even become hydrophobic. The obtainedresults indicate that the electrical and surface properties of thecomposites have been significantly enhanced by the embedded carbonnanotubes.