掺铥氟磷玻璃的结构、热学性质和光谱性质

制备了不同Al(PO3)3含量的掺铥系列氟磷玻璃,研究了其结构、热稳定性和光谱性质。随着Al(PO3)3含量的增加,该系列玻璃的密度降低,折射率增加,差热分析表明,转变温度、析晶起始温度、析晶峰温度和熔化温度增加。Al(PO3)3摩尔浓度在7%~9%时析晶稳定性最佳。采用归一化的拉曼光谱分析了材料的结构和声子状况,对于该系列氟磷玻璃,Al(PO3)3含量的增加不会影响声子能量,但使声子密度增大。测试了样品的吸收光谱,Tm3 的3H6→3F4在第三通信窗口的L波段有明显吸收。与在其它玻璃基质中相比,Tm3 的3F4能级对应能量偏高,3H4能级对应能量偏低,使得3H4→3F4跃迁波长较大,接近于增益迁移光纤放大器的放大波长。扎得奥菲而特(Judd-Ofelt)理论分析表明随着Al(PO3)3含量增加,离子强度参量Ω2增大,Ω6保持相对稳定,Tm3 的能级寿命降低。     

Mössbauer study on LiFePO4 cathode material for lithium ion batteries

Crystalline LiFePO₄ has been synthesized using solid-state, spray pyrolysis, and wet chemical methods. The crystal parameters were obtained from Rietveld’s refinement methods of the X-ray diffraction patterns. A detailed investigation of the Fe valency carried out using Mössbauer spectroscopy at room temperature indicates that Fe is predominantly present in its bivalent state.     

氢同位素化合物TiH2，TiD2和TiT2的电子

根据原子分子反应静力学和群论，确定TiH2，TiD2和TjT2的基电子状态为^3A2．应用基函数6-311G^＊＊和密度泛函理论B3P86方法，全电子计算了氢同位素分子及其钛化物的能量E、定容热容Cv和熵S应用电子振动近似理论，即用单个分子TiH2，TiD2和TjT2中的电子和振动能量和熵近似代表他们处于固态时的能量和熵,计算所得到的金属钛的氢化热力学函数△Hc^0，△S^0，△G^0以及平衡压力与温度的关系，与文献符合很好，这表明电子振动近似理论的可应用性，选用金属钛作为中子靶是很正确的。     

光辐射吸收材料表面形貌与吸收率关系研究

光辐射吸收材料不同的表面形貌对入射光具有不同的多重反射吸收效果,对光辐射的吸收有较大的影响,合适的表面形貌可以提高光辐射有效吸收率.本文通过光线追迹的方法对V形表面、正弦表面、具有正态倾角(平均倾角)分布的表面以及具有正态高度分布的表面进行模拟, 分析了这四种表面对光辐射吸收率的提升效果及其入射角特性.通过倾角分布分析,得出不同表面形貌提升吸收率共同的必要条件,即倾角中心分布至少大于30°,并指出V形表面在正入射时对吸收率提升的优越性. 关键词： 光吸收材料 表面形貌 吸收率 表面倾角分布     

Effect of pure and mixed solvents on the solubility, crystal growth and morphology of ethyl p-dimethylamino benzoate (EDMAB): An organic nonlinear optical material

The effects of pure and mixed solvents of ethanol and acetone on solubility, nucleation and growth of ethyl p-dimethylamino benzoate (EDMAB) were investigated. It was found that solubility of EDMAB increased as the volume ratio of acetone increased in the mixed solvent. Growth experiments were performed at 32 °C using pure and mixed solvents with different volume ratios of ethanol and acetone. Bulk single crystals of EDMAB were grown-in the experiment conducted using mixed solvent of 25% acetone and 75% of ethanol, whereas thin platelet crystal of EDMAB was obtained in the experiment conducted using pure ethanol. The acetone rich system resulted in uncontrolled nucleation with large number of tiny crystals, possibly due to high vapor pressure of acetone. The grown crystals were subjected to various analytical studies such as powder X-ray diffraction, Vickers microhardness, dielectric studies as a function of frequency and optical transmission and the powder Kurtz method.     

A New Higher Order Shear Deformation Model for Static Behavior of Functionally Graded Plates

In this paper, a new displacement based high-order shear deformation theory is introduced for the static response of functionally graded plate. Unlike any other theory, the number of unknown functions involved is only four, as against five in case of other shear deformation theories. The theory presented is variationally consistent, has strong similarity with classical plate theory in many aspects, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. The mechanical properties of the plate are assumed to vary continuously in the thickness direction by a simple power-law distribution in terms of the volume fractions of the constituents. Numerical illustrations concerned flexural behavior of FG plates with Metal-Ceramic composition. Parametric studies are performed for varying ceramic volume fraction, volume fraction profiles, aspect ratios and length to thickness ratios. The validity of the present theory is investigated by comparing some of the present results with those of the classical, the first-order and the other higher-order theories. It can be concluded that the proposed theory is accurate and simple in solving the static behavior of functionally graded plates.     

Luminescence properties of green emission of SiO2/Zn2SiO4:Mn nanocomposite prepared by sol–gel method

Green light emitting Mn²⁺ doped Zn₂SiO₄ particles embedded in SiO₂ host matrix were synthesized by a sol–gel method. After the incorporation of ZnO:Mn nanoparticles in a silica monolith using sol–gel method with supercritical drying of ethyl alcohol in two steps, it was heat treated in air at 1200 °C for 2 h in order to obtain the SiO₂/α-Zn₂SiO₄:Mn nanocomposites. The microstructure of phosphor crystals was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). XRD results indicate that the pure phase α-Zn₂SiO₄ with rhombohedral structure was obtained after thermal treatment at 1200 °C. The SiO₂/α-Zn₂SiO₄:Mn nanocomposites with a Mn doping concentration of 1.5 at% exhibit two broadband emissions in the visible range: a strong green emission at around 525 nm and a second one in the range between 560 and 608 nm. This nanocomposite with a Mn doping concentration of 0.05 shows the highest relative emission intensity. Upon 255 nm excitation, the luminescence decay time of the green emission of Zn₂SiO₄:Mn around 525 nm is 11 ms. The luminescence spectra at 525 nm (⁴T₁–⁶A₁) and lifetime of the excited state of Mn²⁺ ions-doped Zn₂SiO₄ nanocrystals are investigated.     

On the scatter ranges for the elastic moduli of random aggregates of general anisotropic crystals

A randomly inhomogeneous material may have macroscopic properties (elasticity, conductivity) scattered over some uncertainty intervals, despite the idealistic uniqueness assumption of homogenization theory. Based on minimum energy principles and certain statistical isotropy-symmetry hypotheses, our partly third-order bounds on the effective properties of random polycrystals are expected to estimate those scatter ranges. Explicit expressions are given and calculated for the elastic moduli of the random aggregates of some known monoclinic and triclinic crystals, which yield results in agreement with those calculated for higher-symmetry crystals: the moduli are determinable within an accuracy of two or three significant digits in most cases. It is shown, however, that with some real-world exotic crystals the bounds may fall far apart, and further theoretical and experimental studies on them deserve attention.     

Using a pseudo-functionally graded interlayer in order to improve the static and dynamic behavior of wind turbine blade T-bolt root joints

The large wind turbines blades with multi-ton composite structures are mostly connected to the peach-bearings flanges using T-bolt joints which induce shear and bearing stress fields around the cross bolts. The significant differences between the modulus of elasticity of metallic bolts and composite surrounding materials cause stress concentration around interfaced zones and, also, limit the load capacity of the joints. In the present research, a pseudo functionally graded material (PFGM) as an interlayer is used around the cross bolts to examine the reduction of the stress concentration. Some radial variation of the mechanical properties would be considered for this interlayer. The finite element method is used to analyze the structures. Loadings are applied to the center of the cross bolts analogous to the real cases. Both the static and dynamic loadings are studied. For the finite element of the functionally graded material interlayer, a multilayer alternative material with constant properties in each layer is used. The results show that using an isotropic single layer with an average modulus of elasticity and specific thickness decreases the stress concentration of the composite part up to 47%. The various property models for the interlayer also show that an appropriated model can decrease the stress concentration up to 55%. Dynamic transient analyses would be implemented over the joint structure and improved considering to the practical cases. Using the PFGM interlayer decreases the constant and variable parts of the stresses up to 55% and also causes significant increasing of the joint fatigue life.     

超声波对合成介孔材料Al-MCM-41的有序度的影响

在超声频率为20 kHz,电功率为500 W的超声波作用下,分别以Al（NO₃）₃和Al₂ （SO₄）₃做铝源合成了具有不同Si/Al比的Al-MCM-41。XRD结果显示,尽管超声波作用下,掺杂杂原子Al也要降低介孔材料的有序度,但其有序度降低的程度比普通水热法要小,超声波的辅助可以在同样反应时间内得到比普通水热法具有更高有序度的Al-MCM-41,即在掺杂过程中,超声波要比普通搅拌有利于介孔材料保持其骨架稳定性。此外考察了超声波作用时间对产品有序度和粒度的影响。