Reactivity and characterisation of various rank turkish bituminous coal chars

A set of seven bituminous coal chars has been characterised by IR spectroscopy (FTIR), thermogravimetry (TG) and elemental analysis. FTIR study provided suitable information to establish differences between coal samples according to their chemical compositions. The reactivity of these samples was also studied and correlated with the coal parameters of mean vitrinite reflectance, fuel ratio and H/C ratio. The data suggest that reactivity as determined can be correlated with the mean vitrinite reflectance, fuel ratio and H/C ratio (0.90). The order of reactivity of samples were; Amasra (S1) (R _m= 0.65)>Azdavay (S4) (R _m=0.99)»Armutcuk (S2) (R _m=0.81)»Acenta (S3) (R _m=0.92)>Ac2l2k (S6) (R _m=1.11) Cay (S5) (R _m=1.03)>Sogutozu (S7) (R _m=2.14).     

New far infrared laser lines obtained by optically pumping13CD3OD

We have obtained laser action on 34 far infrared lines for the first time in fully deuterated methyl alcohol with the¹³C isotope (¹³CD₃OD), and we have measured the frequency of 13 lines. The molecule was pumped by a cw CO₂ laser. We have measured the wavelength, the relative polarization, the relative intensity of most lines, the frequency, and the CO₂ pump frequency offset of the strongest lines. The new lines are distributed in the wavelength region from 75.27 m to 464.7 m.Supported in part by a joint grant with the U.S. National Science Foundation grant # INT 80-19014 and the Brazilian Conselho Nacional de Pesquisas (CNPq).     

Study of transition metal oxide doped LaGaO3 as electrode materials for LSGM-based solid oxide fuel cells

Transition metal oxide doped lanthanum gallates, La_0.9Sr_0.1Ga_0.8M_0.2O₃ (where M=Co, Mn, Cr, Fe, or V), are studied as mixed ionic-electronic conductors (MIECs) for electrode applications. The electrochemical properties of these materials in air and in H₂ are characterized using impedance spectroscopy, open cell voltage measurement, and gas permeation measurement. Three single cells based on La_0.9Sr_0.1Ga_0.8 Mg_0.2O₃ (LSGM) electrolyte (1.13 to 1.65 mm thick) but with different electrode materials are studied under identical conditions to characterize the effectiveness of the lanthanum gallate-based MIECs for electrode applications. At 800 °C, a single cell using La_0.9Sr_0.1- Ga_0.8Co_0.2O₃ as the cathode and La_0.9Sr_0.1Ga_0.8Mn_0.2O₃ as the anode shows a maximum power density of 88 mW/cm², which is better than that of a cell using Pt as both electrodes (20 mW/cm²) and that of a cell using La_0.6Sr_0.4CoO₃ (LSC) as the cathode and CeO₂-Ni as the anode (61 mW/cm²) under identical conditions. The performance of LSGM-based fuel cells with MIEC electrodes may be further improved by reducing the electrolyte thickness and by optimizing the microstructures of the electrodes through processing. Received: 9 January 1998 / Accepted: 1 May 1998     

The use of 1H NMR microscopy to study proton-exchange membrane fuel cells.

To understand proton-exchange membrane fuel cells (PEMFCs) better, researchers have used several techniques to visualize their internal operation. This Concept outlines the advantages of using 1H NMR microscopy, that is, magnetic resonance imaging, to monitor the distribution of water in a working PEMFC. We describe what a PEMFC is, how it operates, and why monitoring water distribution in a fuel cell is important. We will focus on our experience in constructing PEMFCs, and demonstrate how 1H NMR microscopy is used to observe the water distribution throughout an operating hydrogen PEMFC. Research in this area is briefly reviewed, followed by some comments regarding challenges and anticipated future developments.     

cotpp-pt/c作直接甲醇燃料电池阴极催化剂

四苯基钴卟啉;pt催化剂;直接甲醇燃料电池;氧还原     

An NMR study of methanol diffusion in polymer electrolyte fuel cell membranes

Methanol diffusion in two polymer electrolyte membranes, Nafion 117 and BPSH 40 (a 40% disulfonated wholly aromatic polyarylene ether sulfone), was measured using a modified pulsed field gradient NMR method. This method allowed for the diffusion coefficient of methanol within the membrane to be determined while immersed in a methanol solution of known concentration. A second set of gradient pulses suppressed the signal from the solvent in solution, thus allowing the methanol within the membrane to be monitored unambiguously. Over a methanol concentration range of 0.5–8 M, methanol diffusion coefficients in Nafion 117 were found to increase from 2.9 × 10⁻⁶ to 4.0 × 10⁻⁶ cm² s⁻¹. For BPSH 40, the diffusion coefficient dropped significantly over the same concentration range, from 7.7 × 10⁻⁶ to 2.5 × 10⁻⁶cm² s⁻¹. The difference in diffusion behavior is largely related to the amount of solvent sorbed by the membranes. Increasing the methanol concentration results in an increase in solvent uptake for Nafion 117, while BPSH 40 actually excludes the solvent at higher concentrations. In contrast, diffusion of methanol measured via permeability measurements (assuming a partition coefficient of 1) was lower (1.3 × 10⁻⁶ and 6.4 × 10⁻⁷ cm² s⁻¹ for Nafion 117 and BPSH 40 respectively) and showed no concentration dependence. The differences observed between the two techniques are related to the length scale over which diffusion is monitored and the partition coefficient, or solubility, of methanol in the membranes as a function of concentration. For the permeability measurements, this length is equal to the thickness of the membrane (178 and 132 μm for Nafion 117 and BPSH 40 respectively) whereas the NMR method observes diffusion over a length of approximately 4–8 μm. Regardless of the measurement technique, BPSH 40 is a greater barrier to methanol permeability at high methanol concentrations.     

吸热型碳氢燃料在银、镧改性混合分子筛上的裂解研究

为进一步提高吸热型碳氢燃料的吸热能效，考察了吸热型碳氢燃料NNJ－150在USHY和HZSM－5混合分子筛以及银、镧改性混合分子筛催化剂上的催化裂解。结果表明，在Ag-LaUSY Ag-LaZSM-5(75:25)混合分子筛催化NNJ－150裂解反应中，低碳烯烃选择性较高，催化剂寿命较长。采用此催化剂，能较好满足吸热型碳氢燃料裂解的需要。     

采用Seemann－Bohlin准聚焦X射线衍射仪测量薄膜厚度的误差理论分析

本文从理论上分析了衍射强度比偏差Δ（Ｉ／Ｉ∞）和衍射峰位偏差Δ２θ对Ｓｅｅｍａｎｎ－Ｂｏｈｌｉｎ准聚焦Ｘ射线衍射仪测量表面单层薄膜厚度误差的影响。分析结果表明，降低Δ（Ｉ／Ｉ∞）可提高膜厚的测量精度，在Δ（Ｉ／Ｉ∞）－定的情况下，按μρｔ［Ｓｉｎ（－１）γ＋Ｓｉｎ（－１）（２θ－γ）］＝１选择靶辐射和衍射晶面可使由Δ（Ｉ／Ｉ∞）导致的膜厚测量误差具有极小值；选择高角度衍射线有助于减小试样离焦引起的衍射峰位偏差，亦可降低因衍射角测量偏差导致的膜厚测量误差，当衍射线处于薄膜的法向２θ＝γ＋π／２时，角度项误差（Δｔ／ｔ）（２θ）完全消除。     

高密度燃料HDF-1与橡胶的相容性研究

报道了在室温和70 ℃下橡胶材料G402氟硅胶、丁腈胶5171、丁腈胶4170、贮囊橡胶用合成的高密度燃料HDF-1浸泡后性能如伸长率、邵尔硬度、重量、面积体积的变化，并与采用3号喷气燃料（RP-3）实验结果进行对照。用红外光谱测定了燃料浸泡前后橡胶组成的变化。实验结果表明，G402氟硅胶和贮囊对于HDF-1和RP-3有相近的相容性，丁腈胶5171对HDF-1的相容性比对RP-3的相容性稍差，丁腈胶4170对HDF-1的相容性比对RP-3的相容性更差的结果。因此，丁腈胶5171和丁腈胶4170不能用于HDF-1储存和输送，原使用RP-3系统的橡胶密封件不能直接使用HDF-1。     

高分散直接甲醇燃料电池Pt／C阴极电催化剂的制备过程机理与表征

 通过调变的多元醇法制备了40％Pt／C直接甲醇燃料电池阴极电催化剂，应用透射电镜（TEM）及X射线衍射（XRD）方法表征催化剂．结果表明，由该制备方法可得到高分散，金属粒子粒径分布窄的高载量贵金属催化剂．TEM统计结果表明，调变多元醇法制备的40％Pt／C催化剂的金属粒子平均粒径约为2．9nm．直接甲醇燃料电池单池性能测试表明，该方法制得的40％Pt／C的电催化氧还原能力比同型商品催化剂更好．另外，利用UV－Vis光谱研究了催化剂的制备过程．结果表明，在调变的多元醇法中，Pt4＋的还原是一步完成的．