14N遥测核四极共振中的偏离共振效应

本文对遥测NQR谱中的偏离共振效应作了较详细地研究,发现¹⁴N谱线的强度随偏离共振效应而变化。当偏离共振强度与射频场强度接近时,测得的谱线强度最大。该效应可用来增强¹⁴N遥测NQR谱仪的灵敏度。上述实验现象在理论上采用脉冲的激发带宽方法作了解释和讨论。     

光子加速器的理论研究

研究了光子加速器(即利用等离子体中的朗谬尔波实现光脉冲频率上转换)所涉及的基本物理问题.文中导出了在存在朗谬尔波的条件下,光脉冲频率对于等离子体本底密度及电子密度扰动的依赖关系,并就最大频率转换、光脉冲俘获、波的加速位相(accelerating phase)以及位相滑动(phase slippage)效应进行讨论.     

基于经典控制理论的控制系统计算机辅助设计软件

频率法和根轨迹法是经典控制理论的两个基本的控制系统设计与分析方法。本文主要介绍的两个计算机辅助设计（ＣＡＤ）软件，分别建立在频率法和根轨迹法的基础上。通过这两个ＣＡＮ软件，可以根据给定的单输入单输出（ＳＩＳＯ）控制系统数学模型，进行各种计算，从而得到我们所需要的结果．     

光电检测系统的带宽选择

本文分析光电检测系统的带宽与系统响应时间及信噪比之间的关系。提出在方案设计时根据所要求的响应时间和最佳信噪比初步确定带宽的方法。     

Time‐resolved coherent anti‐Stokes Raman spectroscopy impulsively excited by supercontinuum

Time‐resolved coherent anti‐Stokes Raman scattering (CARS) impulsively excited by a supercontinuum (SC) is investigated. We show that it is critical to optimize the temporal overlapping of the constituent solitons of a SC in order to impulsively excite vibrational modes over a broad frequency range. The cross‐correlation frequency‐resolved optical gating technique is utilized to retrieve the optical response function of molecules under SC impulsive excitation, and background‐free CARS with spectral resolution significantly better than the bandwidth of the probe pulses is achieved. Copyright © 2011 John Wiley & Sons, Ltd.     

Microfabrication of stacks of acoustic matching layers for 15 MHz ultrasonic transducers

This paper presents a novel method used to manufacture stacks of multiple matching layers for 15 MHz piezoelectric ultrasonic transducers, using fabrication technology derived from the MEMS industry. The acoustic matching layers were made on a silicon wafer substrate using micromachining techniques, i.e., lithography and etch, to design silicon and polymer layers with the desired acoustic properties. Two matching layer configurations were tested: a double layer structure consisting of a silicon–polymer composite and polymer and a triple layer structure consisting of silicon, composite, and polymer. The composite is a biphase material of silicon and polymer in 2-2 connectivity. The matching layers were manufactured by anisotropic wet etch of a (1 1 0)-oriented Silicon-on-Insulator wafer. The wafer was etched by KOH 40 wt%, to form 83 μm deep and 4.5 mm long trenches that were subsequently filled with Spurr’s epoxy, which has acoustic impedance 2.4 MRayl. This resulted in a stack of three layers: The silicon substrate, a silicon–polymer composite intermediate layer, and a polymer layer on the top. The stacks were bonded to PZT disks to form acoustic transducers and the acoustic performance of the fabricated transducers was tested in a pulse-echo setup, where center frequency, −6 dB relative bandwidth and insertion loss were measured. The transducer with two matching layers was measured to have a relative bandwidth of 70%, two-way insertion loss 18.4 dB and pulse length 196 ns. The transducers with three matching layers had fractional bandwidths from 90% to 93%, two-way insertion loss ranging from 18.3 to 25.4 dB, and pulse lengths 326 and 446 ns. The long pulse lengths of the transducers with three matching layers were attributed to ripple in the passband.     

谐振式集成光学陀螺解调特性分析

基于激光器频率谱检测技术,沿着光的传输方向分析了光波在谐振式集成光学陀螺系统中的传播,结合输入信号特征,建立频域内的数学模型,通过数值仿真和实验得到了调频检测系统下的解调曲线。按照光的传输方向：激光器、声光晶体移频器、光波导环形谐振器、探测器,利用贝塞尔函数展开和光场耦合模理论分析了谐振式集成光学陀螺解调特性,及其调频调制检测系统解调输出信号与谐振频率偏差之间的关系。通过数值计算,分析了解调曲线的变化规律,得到了施加在激光器压电陶瓷驱动器上调制波形的最佳调制系数。在实验上搭建了激光器频率调制解调技术系统,得到了解调曲线。数值仿真和实验结果表明,当调制系数M=2时,线性工作区间斜率最大,解调曲线最好。实测形状与理论分析结果相符,从解调信号得到±2×10³ rad/s的陀螺动态范围。     

CCD对高空间分辨率波前干涉检测的影响

推导并用实验验证了光强与入射波前在单位像元面积里成近似线性关系,从而得到入射波前经CCD采样后的功率谱密度（PSD）公式.根据该公式,模拟分析了影响CCD采集系统的系统传递函数的各个因素：入射波前、CCD的填充因子及CCD的曝光时间,得出了他们与系统传递函数的定性关系,并且通过实验明确CCD曝光时间对高空间分辨率波前检测不确定度的影响,为高空间分辨率干涉设计提供了理论依据.     

微型同轴脉管制冷机最低制冷温度影响因素的实验研究

本文对微型同轴脉管制冷机最低制冷温度的影响因素进行了实验研究。试验结果表明:在其他运行参数不变的情况下,随着氢浓度的逐渐减少,最低制冷温度也逐渐降低,当氢的摩尔浓度小于20％时,其最低制冷温度和纯氦相差不大。不同的氢氦配比下,该脉管制冷机的最佳运转频率为16.7 Hz。随着系统平均压力的提高,最低制冷温度也随之下降,但变化幅度越来越小。     

Improved DOSY NMR data processing by data enhancement and combination of multivariate curve resolution with non-linear least square fitting

The quality of DOSY NMR data can be improved by careful pre-processing techniques. Baseline drift, peak shift, and phase shift commonly exist in real-world DOSY NMR data. These phenomena seriously hinder the data analysis and should be removed as much as possible. In this paper, a series of preprocessing operations are proposed so that the subsequent multivariate curve resolution can yield optimal results. First, the baseline is corrected according to a method by Golotvin and Williams. Next, frequency and phase shift are removed by a new combination of reference deconvolution (FIDDLE), and a method presented by Witjes et al. that can correct several spectra simultaneously. The corrected data are analysed by the combination of multivariate curve resolution with non-linear least square regression (MCR-NLR). The MCR-NLR method turns out to be more robust and leads to better resolution of the pure components than classic MCR.