The stability analysis of rolling motion of hypersonic vehicles and its validations

The stability of the rolling motion of near space hypersonic vehicles with rudder control is studied using method of qualitative analysis of nonlinear differential equations, and the stability criteria of the deflected rolling motions are improved. The outcomes can serve as the basis for further study regarding the influence of pitching and lateral motion on the stability of rolling motion. To validate the theoretical results, numerical simulations were done for the rolling motion of two hypersonic vehicles with typical configurations. Also, wind tunnel experiments for four aircraft models with typical configurations have been done. The results show that: 1) there exist two dynamic patterns of the rolling motion under statically stable condition. The first one is point attractor, for which the motion of aircraft returns to the original state. The second is periodic attractor, for which the aircraft rolls periodically. 2) Under statically unstable condition, there exist three dynamic patterns of rolling motion, namely, the point attractor, periodic attractor around deflected state of rolling motion, and double periodic attractors or chaotic attractors.     

连续激光辐照ZnSe/MgF2/K9滤光片的透射特性研究

分析了连续激光辐照ZnSe/MgF2/K9滤光片引起透射特性的变化。在室温条件下,用波长0.632 8μm激光作为探测光束,测量了1.06μm连续激光辐照ZnSe/MgF2/K9滤光片温升引起薄膜折射率的改变,导致探测光束通过干涉滤光片后透过率的热致非线性变化。在光斑直径0.75mm条件下,测量了不同功率激光辐照ZnSe/MgF2/K9滤光片引起温升随时间的变化。在激光功率30W,辐照时间2.52s条件下,实验观测到ZnSe/MgF2/K9滤光片薄膜破坏温度约为90℃,辐照时间10s时干涉滤光片形成的薄膜龟裂形貌。     

高反射膜激光零几率损伤阈值的实验研究

在确定光学薄膜激光损伤阈值的实验数据处理过程中,发现一些样品的数据点分布偏离直线型式。对此,用国际标准规定的零几率来确定损伤阈值的同时,对测试数据点采用了不同的非直线拟合,也得到一个零几率损伤阈值。比较两者差异,并与实验测试结果对照,发现这些样品采用非直线拟合得出的零几率损伤阈值与实际情况更接近一些。     

热处理条件对PVA薄膜阻氢性能的影响

采用XRD测定了PVA薄膜在不同热处理条件下的结晶度,并用自行设计的渗氢系数测量系统研究了在不同热处理条件下的PVA薄膜阻氢性能的变化规律。结果表明,PVA薄膜的热处理温度越高,其结晶度越高,越有利于提高PVA薄膜的阻氢性能,但热处理温度宜选择在180℃以下,以防止PVA薄膜热降解,另一方面,在PVA的玻璃化转变温度以下进行热处理同样能够提高PVA薄膜的阻氢性能,而醇解度较低的PVA薄膜在玻璃化转变温度以下经热处理后的阻氢性能提高的幅度较大。     

电子束、离子辅助和离子束溅射三种工艺对光学薄膜性能的影响

运用电子束、离子辅助和离子束溅射三种镀膜工艺分别制备光学薄膜,包括单层氧化物薄膜和增透膜,然后采取一系列测试手段,如Zygo轮廓仪、原子力显微镜、表面热透镜技术和X射线衍射等技术,来分析和研究不同的工艺对这些薄膜性能的不同影响,以判断合理的沉积工艺。     

Novel Protonic Conductive Silicates Produced by the Sol-Gel Method

ABSTRACT

Materials which display ionic conductivity were produced by the sol-gel and microemulsion-gel methods. The charging and discharging characteristics were investigated and it was found that a single ionic species was responsible for the conduction, the ionic species being residual protons from the initial component mixture. The complex impedence of various samples was measured and the ionic conductivities ranged in value from 9 × 10^?8 to 1 × 10^?5 ohm^?1 cm^?1. An Arrhemius plot for a microemulsion-gel revealed that the energy of activation was 0.15 eV.     

Influence of the e-beam irradiation and photo-oxidation aging on the structure and properties of LDPE-OMMT nanocomposite films

In this paper two systems, polyethylene (LDPE) and polyethylene/commercial organo-modified montmorillonite (LDPE/OMMT) nanocomposite, were subjected to e-beam irradiation at different doses and both the molecular modifications and mechanical properties have been investigated through solubility, FT-IR, calorimetric and tensile tests. Moreover, in some of the irradiated systems photo-oxidation aging was performed and its effects were studied. The results show an enhancement with irradiation of the positive effect of the nano-filler loading, related to the increase of the mechanical properties, due to the increase of the nano-filler polymer interaction.Nevertheless calorimetric and FT-IR data indicate that the well known reduction of LDPE/OMMT nanocomposite resistance to photo-oxidation ageing, with respect to LDPE, is amplified by ionizing radiation.     

XPS和AES研究A3钢表面杂多酸钝化膜

通过比较多种杂多酸及铬酸盐等纯化剂的钝化效果，发现Ｈ３ＰＭｏ１２Ｏ４０是一种优良的纯化剂。在５５℃，ｐＨ１．０的条件下，Ａ３钢在２０ｇ／Ｌ的Ｈ３ＰＭｏ１２Ｏ４０溶液中能形成致密的耐蚀性保护膜。ＡＥＳ结合Ａｒ＾＋溅射测得膜的元素组成为：Ｐ１．９％，Ｍｏ１７．９％，Ｏ６９．６％，Ｆｅ１０．７％．ＸＰＳ测得膜中Ｍｏ以Ｍｏ（Ⅵ）、Ｍｏ（Ｖ）ｔ Ｍｏ（Ⅳ）三种氧化态存在。红外及Ｒａｍａｎ光谱表明，膜的主要振     

a-CdSe超快光电探测器特性研究

本文报道淀积条件对非晶态硒化镉(a-CdSe)薄膜微区结构的影响,并对利用a-CdSe为光敏介质的超快光电探测器的特性进行了比较深入的测试研究。     

Deterministic equivalent for a continuous-time linear-convex stochastic control problem

We consider a finite-horizon control model with additive input. There are two convex functions which describe the running cost and the terminal cost within the system. The cost of input is proportional to the input and can take both positive and negative values. It is shown that there exists a deterministic control problem whose optimal cost is the same as the one in the stochastic control problem. The optimal policy for the stochastic problem consists of keeping the process as close to the optimal deterministic trajectory as possible.This research is supported by NSERC Grant A4619, MRCO, NSF Grant DMS-86-01510, and AFOSR Grant 87-0278.