碳纤维微电极恒电位活化及测定金属离子的研究

碳纤维微电极已被广泛应用于电化学研究和分析测定,该电极尺寸极小,在分析性能上与常规电极有显著不同,在不镀汞的情况下,用碳纤维电极直接测定金属离子几乎没有明显的伏安响应,本文提出用+2.5 V恒电位预先活化碳纤维电极,使测定灵敏度大为提高,在双电极体系和静止溶液中,采用溶出伏安法可测定10~(-9)级金属离子,以同样的方法清洗电极,测定结果重现性良好,由于分析过程中不使用汞,该电极的测定范围大大增加,特别是用于氧化还原电位较正的金属离子测试,根据循环伏安法、扫描电镜和电子能谱的研究,发现碳纤维表面状况在处理前后有很大变化,并与测定灵敏度密切相关。     

Adsorption separation of terpene lactones from Ginkgo biloba L. extract using glass fiber membranes modified with octadecyltrichlorosilane

In this study porous glass fiber membranes were modified by reaction with octadecyl-trichlorosilane to form C18 hydrophobic membranes. The contact angle and the CH2 vibration bands at 2855 and 2920 cm(-1) found by FTIR measurements verified the successful immobilization of C18 groups on the glass fiber membranes. The resulting C18 hydrophobic membranes were used to adsorb terpene lactones from crude Ginkgo biloba L. extracts. In batch adsorption processes, the modified C18 membranes exhibited a better adsorption performance than commercial C18 solid phase extraction adsorbents. Different desorption solvents were tested and ethyl acetate was found to preferentially desorb terpene lactones from the modified C18 membranes. In flow adsorption experiments at 1 mL/min, terpene lactone contents higher than 6 wt% (the standardized content) could be achieved in the elution step using ethyl acetate.     

STUDIES ON THE PREPARATION OF ZINC-CONTAINING ACTIVATED CARBON FIBERS AND THEIR ANTIBACTERIAL ACTIVITY

1. INTRODUCTION Microbial pollution will bring about various problems in industry and other vital fields, such as causing decomposing of materials, harming people抯 health. In order to reduce these problems, new antibacterial materials have been demanded. Recently, much attention has been paid to inorganic materials including zinc oxide [1~4]. These inorganic antibacterial materials are now substituting for organic materials to avoid releasing noxious organic molecules harmful to humans;…     

MORPHOLOGIES AND GAS SEPARATION PROPERTIES OF MELT-SPUN ASYMMETRIC POLY(4-METHYL-1-PENTENE)HOLLOW FIBER MEMBRANES*

Poly(4-methyl-1-pentene) (PMP) hollow fiber membranes were prepared by the melt-spun and cold-stretch(MSCS) method. Scanning electronic microscopy (SEM) was used to characterize the section and surface structures of themembranes with special asymmetric structure. The preliminary results of gas permeation measurements indicated that the resultant hollow fiber membranes have the potential ability for oxygen/nitrogen separation.     

铌酸锂单晶光纤包层研究

通过镁离子内扩散铌酸锂单晶光纤，以改变晶纤表层的折射率，首次在国内实现了沿不同轴向生长、不同掺杂的铌酸锂单晶光纤的芯－包层波导结构。通过匹配扩散温度、扩散时间、ＭｇＯ膜厚等扩散参数及选择合适的晶纤直径，实现了晶纤具有阶跃和抛物折射率分布的包层，并对包层晶纤的模式特性进行了观察，得到低次模传输。     

Applicability of glass fiber as a support material for generation of gaseous standard mixtures using thermal decomposition of the surface compound. Calibration of analytical equipment

The use of glass fiber as a support material for a surface compound serving to generate gaseous standard mixtures of ethene is described. The technique is based on the process of thermal decomposition of the surface compound in a desorber connected on‐line via a multi‐port valve to the calibrated device. The surface compound undergoes thermal decomposition at 245°C, yielding known amounts of ethene. The method enables on‐line preparation of a standard mixture immediately before the calibration step. Consequently, it can be also applied for the generation of standard mixtures containing volatile, malodorous, unstable, and toxic compounds.     

Fabrication of PbTiO3 Ceramic Fibers by Sol-Gel Processing

The sol-gel processing was applied to the fabrication of PbTiO₃ fibers. Pb(CH₃COO)₂·3H₂O and Ti(OC₃H ₇ ⁱ )₄ were refluxed with stirring in 2-methoxyethanol to form Pb-methoxyethoxide and Ti-methoxyethoxide, respectively, followed by mixing with stirring in 2-methoxyethanol to form Pb−Ti double alkoxide. The hydrolysis and polycondensation reaction of this double alkoxide gave polymerized products, and as a result the viscosity of the solution increased, suggesting that linear polymers were produced through the hydrolysis and polycondensation reaction. Homogeneous PbTiO₃ gel fibers were drawn from the spinnable viscous solutions, which were wellcrystallized into perovskite type PbTiO₃ at 650°C. The heat-treated fibers were a few centimeters long and from 10 to 100 μm in diameter. The fiber was made up of extremely uniform grains. Electron diffraction revealed a preferred growth of (101) planes along the fiber axis, which might be due to the linear molecular characteristics of the alkoxide.     

Silicon carbide nanotubes and nanotubular fibers: Synthesis, stability, structure, and classification

Published data on silicon carbide nanotubes (SiC-NT) are analyzed. According to theoretical calculations, single-layer SiC-NTs do not dissociate, but they have not yet been detected experimentally. According to the experimental data, metastable SiC-NTs with walls consisting of several layers and nanotube fibers were produced. The optimized structure of single-layer SiC-NTs was calculated by the RHF/6-31G quantum-chemical method. The possibility of obtaining SiC-NTs by gas-phase chemical deposition from methyltrichlorosilane in the temperature range of 800–1000 °C was investigated. Nanofibers and polygrained SiC nanotubes were obtained, but ordinary layer SiC nanotubes were not detected. To remove the inconsistencies it was first proposed to classify the nanotubes according to the structure of their walls, separating all the SiC-NTs into three types: 1) ordinary layer nanotubes with rolled layers, similar to carbon nanotubes; 2) polynanocrystalline nanotubular fibers or nanotubes with walls consisting of linked differently oriented nanograins; 3) monocrystalline synthetic nanotubes with ideal crystalline walls. It was concluded that the ordinary SiC-NTs of the first type are unstable with the exception of one-or two-layer nanotubes; stable SiC-NTs of the first type and SiC-NTs of the third type have not yet been discovered; only nanotubular fibers of the second type were obtained experimentally. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 1, pp. 3–13, January–February, 2006.     

用热聚法固定指示剂的光纤氧气传感器研究

采用热聚法将甲叉双丙烯酰胺（MBBA）聚合并共价交联在硅烷化的玻璃微珠上 ，同时将指示剂Ru（Ⅱ）-邻啡咯啉配合物物理包埋于聚合物中，研制了一种基于 荧光猝灭原理的光纤氧气传感器，采用NaHSO_3-O_2-MnSO_4体系引发MBBA水溶液热 聚合后应，通过确定NaHSO_3,MnSO_4,MBBA和Ru(phen)_3Cl_2的最佳反应浓度以及 玻璃微珠的尺寸，优化了聚合反应条件，改善了指示剂的固定效果，制备了性能较 好的传感器探头，该传感器的检测下限为5×10~(-6)(V/V)，响应时间为10s该传感 器连续工作50min,重复性标准偏差为±1%。     

黄麻塑料复合材料

本文介绍了国外黄麻塑料复合材料研究开发的历史和现状。说明利用各式黄麻纤维产物作为塑料增强剂以生产低成本、轻重量复合材料方面已取得成功,其发展前景具有很大吸引力。