The response of a single TE102 and double TE104 rectangular cavity to the insertion of samples contained in tubes with variable wall thickness and a quartz Dewar into the cavity has been analyzed. A direct, indirect, and concurrent (positive or negative) “lens effect” inside the double TE104 rectangular cavity is discussed. The experimental dependence of the EPR signal intensity on the wall thickness of the sample tube, δ, for the line-like samples with identical length of the sample material column, L=30 mm, recorded in the microwave cavity showed a directly proportional increase of the relative “lens effect” with the increase of the wall thickness of the tube in the interval, δ∈<0.1 mm, >0.5 mm. The insertion of the variable-temperature double-wall quartz Dewar (home-built, resonant frequency shift, ca. −300 MHz) into the single TE102 rectangular cavity showed the same relative “lens effect”, with ca. 1.5-time increase of the EPR signal intensity, for a point-like sample and the line-like samples with material columns of diameter of 1 and 1.3 mm, and wall thickness of the sample tubes, δ∈<0.1 mm, >0.5 mm. The increased effect of the Dewar arises because the active volume of the quartz Dewar tube walls is always much more larger than the active volume of the sample tube wall. In the case of the double TE104 rectangular cavity, the insertion of the quartz Dewar: (i) into the same cavity, in which the sample is present, caused a direct “lens effect”, with ca. 1.8-fold increase of the EPR signal intensity; however, (ii) into the complementary cavity, in which the sample is absent, caused an indirect “lens effect”, with ca. 0.6-fold decrease of the EPR signal intensity. With the Dewar and sample in one cavity and a large empty sample tube in the complementary cavity, a concurrent (positive or negative) “lens effect” can be observed. Thus, the possible increase/decrease of the EPR signal intensity depends on the volume ratio of the quartz Dewar tube walls and large sample tube wall inserted into the double TE104 rectangular cavity. Each of the above phenomena may be a significant source error in quantitative EPR spectrometry unless the samples to be compared in the quantitative EPR analysis are contained in sample tubes having the same wall thickness and each EPR spectra should be recorded inside an identical quartz Dewar. 相似文献
In response to the rapid advancement of auto-refractor technology, most optometry shops provide refraction services. Despite their speed and convenience, the measurement values provided by auto-refractors include a significant degree of error due to psychological and physical factors. Therefore, there is a need for repetitive testing to obtain a smaller mean error value. However, even repetitive testing itself might not be sufficient to ensure accurate measurements. Therefore, research on a method of measurement that can complement auto-refractor measurements and provide confirmation of refraction results needs to be conducted. The customized optometry model described herein can satisfy the above requirements. From the existing optical technologies, using human eye measurement devices to obtain individual relevant optical feature parameters is no longer difficult. These parameters allow us to construct an optometry model for individual eyeballs. They also allow us to compute spot diagrams produced from the optometry model using the CODE V macro programming language before recognizing the geometrical spot diagram with the back-propagation neural network algorithm to obtain the accurate refractive diopter. Results show that the accuracy achieved was above 98% and that this application could significantly enhance the service quality of refraction. 相似文献
A colorimetric Al3+ sensor based on fluorescence recovery of a conjugated copolymer-ATP complex is proposed. An optimized ratio of two polythiophene (PT) monomers is utilized to synthesize copolymer (CP) that yielded maximized colorimetric response for Al3+ in deionized (DI) and tap water. The electrostatic disassembly of CP-ATP upon addition of Al3+ led to an evident visual color change. The lowest concentration of Al3+ for naked eye observation is around 4 μM, which is below the threshold levels in drinking water according to European Economic Community (EEC) standard. Besides, the proposed assay showed a similar response to Al3+ in tap water. The proposed methodology showed selective and sensitive detection for Al3+ in analytically relevant concentration ranges without involving sophisticated instrumentation, illustrating the applicability for on-site drinking water monitoring. 相似文献
ABSTRACT Thermal lens spectrometry has been used for the determination of iron in calf serum. The method is based on dissociation of Fe3+ from proteins, reduction of Fe3+ to Fe2+ and formation of a coloured complex between Fe2+ and bathophenanthroline. Contrary to the spectrophotometric method, it is shown that thermal lens spectrometry is less sensitive to scattering caused by the presence of small particles remaining in the test solution after the deproteinization step. The background signal is very small and the response is only slightly dependent on the amount of scattering particles. The method is reliable, sensitive and reproducible. The limit of detection for iron is 4 ppb and the relative standard deviation is around 2%. It is expected that the volume of serum sample necessary for an analysis can be reduced to less than 100 μl. 相似文献
This report describes development of an in silico, expert rule-based method for the classification of chemicals into irritants or non-irritants to eye, as defined by the Draize test. This method was developed to screen data-poor cosmetic ingredient chemicals for eye irritancy potential, which is based upon exclusion rules of five physicochemical properties – molecular weight (MW), hydrophobicity (log P), number of hydrogen bond donors (HBD), number of hydrogen bond acceptors (HBA) and polarizability (Pol). These rules were developed using the ADMET Predictor software and a dataset of 917 eye irritant chemicals. The dataset was divided into 826 (90%) chemicals used for training set and 91 (10%) chemicals used for external validation set (every 10th chemical sorted by molecular weight). The sensitivity of these rules for the training and validation sets was 72.3% and 71.4%, respectively. These rules were also validated for their specificity using an external validation set of 2011 non-irritant chemicals to the eye. The specificity for this validation set was revealed as 77.3%. This method facilitates rapid screening and prioritization of data poor chemicals that are unlikely to be tested for eye irritancy in the Draize test. 相似文献
Visible light excitable rhodamine B derivative (TARDHD) has been developed for fluorescence and naked eye detection of histidine in aqueous medium. TARDHD shows 45 fold fluorescence enhancement in the presence of histidine. It forms Schiff base with histidine and stabilizes via intra-molecular H-bonding. TARDHD can efficiently detect intracellular histidine. 相似文献
Conventional optics is diffraction limited due to the cutoff of spatial frequency components, and evanescent waves allow subdiffraction optics at the cost of complex near‐field manipulation. Recently, optical superoscillatory phenomena were employed to realize superresolution lenses in the far field, but suffering from very narrow working wavelength band due to the fragility of the superoscillatory light field. Here, an ultrabroadband superoscillatory lens (UBSOL) is proposed and realized by utilizing the metasurface‐assisted law of refraction and reflection in arrayed nanorectangular apertures with variant orientations. The ultrabroadband feature mainly arises from the nearly dispersionless phase profile of transmitted light through the UBSOL for opposite circulation polarization with respect to the incident light. It is demonstrated in experiments that subdiffraction light focusing behavior holds well with nearly unchanged focal patterns for wavelengths spanning across visible and near‐infrared light. This method is believed to find promising applications in superresolution microscopes or telescopes, high‐density optical data storage, etc.