金属Cu低指数表面熔化行为的分子动力学模

采用Mishin镶嵌原子势, 通过分子动力学方法模拟了金属Cu的低指数表面在不同温度的表面熔化行为, 分析了熔化过程中系统结构组态的变化以及固-液界面迁移情况. 金属Cu的(100)和(110)表面在低于熔点发生预熔化, 而(111)表面存在明显的过热现象. 准液体层的厚度随温度升高而增加, 热稳定性与表面的密排顺序一致, 按(111)、(100)、(110)顺序增大. 当温度高于热力学熔点时, 固液界面的移动速度与温度成正比, 外推得到热力学熔点约为1360～1380 K, 与实验结果1358 K吻合良好. 动力学系数定义为界面移动速度与过热程度的比值, 表现为明显的各向异性: k100=39 cm•s−1•K−1, k110=29 cm•s−1•K−1, k111=20 cm•s−1•K−1. k100与k110之间的比例符合collision-limited理论, (111)密排面有与其它低指数表面不同的熔化方式.     

Transport properties and electroanalytical response characteristics of drotaverine ion-selective sensors

The construction and electroanalytical response characteristics of poly(vinyl chloride) matrix ion-selective sensors (ISSs) for drotaverine hydrochloride are described. The membranes incorporate ion-association complexes of drotaverine with tetraphenylborate, picrate, tetraiodomercurate, tetraiodobismuthate, Reinecke salt, and heteropolycompounds of Keggin structure—molybdophosphoric acid, tungstophosphoric acid, molybdosiliconic acid and tungstosiliconic acid as electroactive materials for ionometric sensor controls. These ISSs have a linear response to drotaverine hydrochloride over the range 8×10^–6 to 5×10^–2 mol L^–1 with cationic slopes from 51 to 58 mV per concentration decade. These ISSs have a fast response time (up to 1 min), a low determination limit (down to 4.3×10^–6 mol L^–1), good stability (3–5 weeks), and reasonable selectivity. Permeabilities and ion fluxes through a membrane were calculated for major and interfering ions. Dependences of the transport properties of the membranes on the concentrations of the ion exchanger and near-membrane solution and their electrochemical characteristics are presented. The ISSs were used for direct potentiometry and potentiometric titration (sodium tetraphenylborate) of drotaverine hydrochloride. Results with mean accuracy of 99.1±1.0% of nominal were obtained which corresponded well to data obtained by use of high-performance liquid chromatography.     

光度分析中协同系数补偿方法的研究──三次标准加入法同时测定钼、钨和钛

本文在两次标准加入法[1]的基础上，提出了三组份同时测定的三次标准加入法，并应用于钼、钨和钛的流动注射同时测定。测定条件：［水杨基荧光酮（SAF）］＝1．25　×10-4mol／L，［溴化＋六烷基三甲基铵（CTMAB）」＝2．5×10－3mol／L，pH1．35，25℃，采样、进样时间分别为10s和18s，进样频率128次／h。为消除组份间协同作用引起的吸光度加合性的偏离，定义了三组份协同系数。将其引入三组份同时测定方法，补偿了吸光度对线性的偏离。补偿后钼、钨和钛的测定范围分别为0．05～0．35，0．25～1．00，0．025～0．30mg／L。测定了钢样及模拟样品中钼、钨和钛含量，结果较好。     

聚硅烷亚芳弹性体的凝胶渗透色谱测量

用简易GPC柱研究了在未知合适的Mark-Houwink 系数的情况下,通过GPC和特性粘度的数据,同时计算出宽分布硅烷亚芳弹性体聚合物的分子量和这种类型聚合物的 Mark-Houwink 系数的方法。装柱填料为多孔硅胶球,理论塔板数 4200—5500块/米以上,塔板高度 0.7—0.9毫米。其分子量分布宽度指数在2左右。素炼后,分子量分布变窄,分子量下降。     

分子轨道图形理论中对称轴定理

本文试图以浅显明确的形式描述对称轴定理，使之能与对称面定理相媲美，并对对称轴定理作一定的扩展，给出分子轨道构造定理。     

Pitzer model parameters for sparingly soluble salts from solubility measurements. The systems TlCl+SrCl2+H2O and TlCl+BaCl2+H2O at 25°C

The solubility of thallium(I) chloride has been determined in aqueous solutions of strontium chloride and barium chloride at concentrations up to 1.5 mol kg^–1. The data were analyzed using Pitzer's equations without making explicit assumption of association to ion pairs by assuming =3 instead of =2, with the ⁽¹⁾ term for TlCl being equivalent to the ⁽²⁾ term for 2-2 electrolytes. Best values of ⁽⁰⁾ and ⁽¹⁾ for TlCl are recommended together with K _s , the activity solubility product. These were used to fit the present solubility data and derive the Pitzer model mixture parameters relevant to the systems, _fTIN and _fTINCl (N=Sr, Ba). Mixture parameters for TlCl+MCl+H₂O systems are also derived to complete the parameter base. The fit of the experimental data was found to be worse when higher-order terms for asymmetrical mixing were included in the analysis. Activity coefficients for thallium(I) chloride in the mixtures are derived.     

Experimental study of the concentration dependence of the soret coefficient by thermal field-flow fractionation: the case of polystyrene in decalin

Summary Thermal field-flow fractionation separates polymers with high selectivity according to their Soret coefficient,S _τ, hence, according to their molar mass, and therefore consitutes an efficeint physicochemical tool for the determination of the Soret coefficient of a given polymer in the carrier liquid from its retention time. However, the polymer concentration in the sample influences the retention time and, hence, the value ofS _τ derived from it. An experimental study of the influence of sample concentration on retention,S _τ, and peak shape was performed for the polystyrene-decalin system over a relatively large temperature domain and for various molar masses. It is found that the retention time and the value ofS _τ increase with increasing sample concentration, the more so as the cold wall temperature is lower. This appears to be in contradiction with the general non-equilibrium thermodynamic expression derived for polymer-solvent systems with positive second virial coefficients, such as the present system over the temperature range investigated. There seems to be a temperature for which the dependence ofS _τ on sample concentration vanishes. This temperature is about 375 K for the polystyrene-decalin system. As the sample concentration increases, the peak barycentre and the standard deviation increases. As the peaks are fronting, the skewness is negative and becomes more negative as the sample concentration increases. The peak skewness appears to be a good indicator of the onset of sample concentration effects. The threshold concentration, for which these effects begin to become significant, decreases with increasing molar mass.     

Role of Ion exchange in permeation processes

The single ion transport of transition metal ions like Cu²⁺, Co²⁺, Ni²⁺ and Zn²⁺ were carried out through the H⁺ and alkali metal ion forms of Nafion membrane. These studies showed that the ion exchange selectivity coefficient of the permeating ion had an effect on its transport process. It was found that the diffusion coefficient values (D) were directly proportional to the selectivity coefficient (K). This shows that the initial stage of permeation is governed by ion exchange process (effect of K on D).     

Dielectric properties of beryllia ceramics in the near-millimeter wavelength range

We report the refractive indices and absorption coefficients for four beryllia (BeO) ceramic samples. These dielectric properties have been measured over the range from 4 to 18 cm^–1 by use of a Michelson interferometer. The index n, follows the linear relationship n=0.6517 cm³/g×+0.7130 with density, , over the range 2.8<<3.0 g/cm³.     

The structure and electrochemical characteristics of La0.67Mg0.33 (Ni0.8Co0.1Mn0.1) x (x=2.5–5.0) multiphase alloys for nickel-metal hydride batteries

This paper presents results concerning structure and electrochemical characteristics of the La_0.67Mg_0.33 (Ni_0.8Co_0.1Mn_0.1) _x (x=2.5–5.0) alloy. It can be found from the result of the Rietveld analyses that the structures of the alloys change obviously with increasing x from 2.5 to 5.0. The main phase of the alloys with x=2.5–3.5 is LaMg₂Ni₉ phase with a PuNi₃-type rhombohedral structure, but the main phase of the alloys with x=4.0–5.0 is LaNi₅phase with a CaCu₅-type hexagonal structure. Furthermore, the phase ratio, lattice parameter and cell volume of the LaMg₂Ni₉phase and the LaNi₅ phase change with increasing x. The electrochemical studies show that the maximum discharge capacity increases from 214.7 mAh/g (x=2.5) to 391.1 mAh/g (x=3.5) and then decreases to 238.5 mAh/g (x=5.0). As the discharge current density is 1,200 mA/g, the high rate dischargeability (HRD) increases from 51.1% (x=2.5) to 83.7% (x=3.5) and then decreases to 71.6% (x=5.0). Moreover, the exchange current density (I ₀) of the alloy electrodes first increases and then decrease with increasing x from 2.5 to 5.0, which is consistent with the variation of the HRD. The cell volume reduces with increasing x in the alloys, which is detrimental to hydrogen diffusion and accordingly decreases the low-temperature dischargeability of the alloy electrodes.