Studies on thermal and morphological properties of 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane-epoxy-bismaleimide matrices

A new cyanate ester monomer, 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane has been synthesized and characterized. Epoxy modified with 4, 8 and 12% (by weight) of cyanate ester were made using epoxy resin and 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane and cured by using diaminodiphenylmethane. The cyanate ester modified epoxy matrix systems were further modified with 4, 8 and 12% (by weight) of bismaleimide (N,N′-bismaleimido-4,4′-diphenylmethane). The formation of oxazolidinone and isocyanurate during cure reaction of epoxy and cyanate ester blend was confirmed by IR spectral studies. Bismaleimide-cyanate ester-epoxy matrices were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and heat deflection temperature (HDT) analysis. Thermal studies indicate that the introduction of cyanate ester into epoxy resin improves the thermal degradation studies at the expense of glass transition temperature. Whereas the incorporation of bismaleimide into epoxy resin enhances the thermal properties according to its percentage content. However, the introduction of both cyanate ester and bismaleimide influences the thermal properties according to their percentage content. DSC thermogram of cyanate ester modified epoxy and bismaleimide modified epoxy show unimodel reaction exotherms. The thermal degradation temperature and heat distortion temperature of the cured bismaleimide modified epoxy and cyanate ester-epoxy systems increased with increasing bismaleimide content. The morphology of the bismaleimide modified epoxy and cyanate ester-epoxy systems were also studied by scanning electron microscopy. Copyright © 2003 John Wiley & Sons, Ltd.     

FexNi100−x nanometric films deposited by laser ablation on SiO2/Si substrates

Fe_xNi_100−x nanometric films were deposited on SiO₂/Si substrates at room temperature using the pulsed laser deposition technique. The targets were Fe-Ni amorphous magnetic foils with composition Fe₅₀Ni₅₀, Fe₃₅Ni₆₅ and Fe₂₂Ni₇₈. Morphological and structural properties of the deposited films were investigated using scanning electron microscopy, Rutherford backscattering spectrometry, grazing incidence X-ray diffraction, and X-ray reflectivity. Electrical and magnetic characteristics of the films were investigated by using the four-point probe and the magneto-optic Kerr effect techniques, respectively. The film properties are strictly dependent on the Fe-Ni compositional ratio.     

Cu-MgF2复合纳米金属陶瓷薄膜的电导特性研究

用射频磁控共溅射法制备了Cu体积分数分别为 10 % ,15 % ,2 0 %和 3 0 %的Cu MgF2 复合金属陶瓷薄膜 .用x射线衍射、x射线光电子能谱和变温四引线技术对薄膜的微结构、组分及电导特性进行了测试分析 .微结构分析表明 :制备的Cu MgF2 复合薄膜由fcc Cu晶态纳米微粒镶嵌于主要为非晶态的MgF2 陶瓷基体中构成 ,Cu晶粒的平均晶粒尺寸随组分增加从 11 9nm增至 17 8nm .5 0— 3 0 0K温度范围内的电导测试结果表明 :当Cu体积分数qM 由 15 %增加到 2 0 %时 ,Cu MgF2 复合薄膜的电阻减小了 8个量级 ,得出制备的复合薄膜渗透阈qCM 应处于 15 %和 2 0 %之间 .qM 在 10 %和 15 %之间的薄膜呈介质导电状态 ,而在 2 0 %和 3 0 %之间的薄膜则呈金属导电状态 .从理论上讨论了复合薄膜中杂质电导和本征电导的激活能及其对电导的贡献 ,并讨论了Cu MgF2 复合纳米金属陶瓷薄膜的渗透阈 ,得到了和实验一致的结果     

超分子有机薄膜

利用超分子有机薄膜技术能制成新的传感分子电子器件、光学器件和生物分子器件等，受到跨学科高技术研究领域的重视。本文描述了超分子有机薄膜的制备方法以及在各应用领域的研究状况。重点介绍了我们研究组在近20年工作中，利用LB膜技术，在光电器件、气体传感技术和光学非线性，特别是在生物传感技术方面的研究成果。按照生物体系提供的信息，模拟合成功能分子，建造有组织的分子组装体，以便用来研究依赖于分子排列的生物物理化学效应。     

Micromechanisms and Mechanics of Damage and Fracture in Thin Film/Substrate Systems

The purpose of this paper is to review the mechanisms and available theoretical methods for modeling the strength and failure of thin film/substrate systems     

Determination of the rheological behavior of epoxy–amine thermosets by dynamic mechanical analysis: Isothermal methods versus nonisothermal methods

The reticulation process of an epoxy resin using an amine as a cure agent was studied at different temperatures and concentrations of the cure agent with dynamic mechanical thermal analysis. The study was performed under both isothermal and nonisothermal conditions, and a temperature–time–transformation diagram was obtained. The measurements from the two modes gave similar results, although the nonisothermal mode required fewer experiments. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1965–1977, 2003     

酞菁钴薄膜的折射率及吸收特性

通过真空镀法在单晶硅片上制备了酞菁钴薄膜，在波长扫描和入射角可变全自动椭圆偏振光谱仪上研究了ＣｏＰｃ薄膜的椭偏光谱并分析了其电子结构。     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Improved coating method for uniform polymer layer in infrared hollow fiber

An improved coating method was proposed in order to form a uniform polymer layer in the fabrication of cyclic olefin polymer-coated silver (COP/Ag) hollow fiber. A COP solution was flowed in a closed loop, in which the silver-coated tube was used as a part of the loop. Owing to the constant flowing speed of the COP solution and the airtight flowing environment, a COP layer was uniformly formed. The hollow fibers attain high performance and deliver multi-wavelength laser light from the infrared to the visible simultaneously. The method was successfully applied to the fabrication of practical hollow fibers with 2 m length for the near and mid-infrared lasers.     

Epoxy resin containing polyphenylsilsesquioxane: Preparation,morphology, and thermomechanical properties

Polyphenylsilsesquioxane (PPSQ) was incorporated into an epoxy resin to prepare organic–inorganic composites, and two strategies were adopted to afford composites with different morphologies. Phase separation induced by polymerization occurred in the physical blending system. However, nanostructured composites were obtained when a catalytic amount of aluminum triacetylacetonate was added to mediate the reaction between PPSQ and diglycidyl ether of bisphenol A (DGEBA). The intercomponent reaction significantly suppressed the phase separation on the micrometer scale. Organic–inorganic composites with different morphologies displayed quite different thermomechanical properties. Both differential scanning calorimetry and dynamic mechanical analysis showed that the nanostructured composites possessed higher glass‐transition temperatures than the phase‐separated composites with the same loading of PPSQ, although the intercomponent reaction between PPSQ and DGEBA reduced the crosslinking density of the epoxy matrix. This result was ascribed to the presence of nanosized PPSQ domains in the nanostructured composites, which acted as physical crosslinking sites and thus reinforced the epoxy networks. The nanoreinforcement of the PPSQ domains afforded the enhanced dynamic storage modulus for the nanostructured composites in comparison with the phase‐separated composites with a PPSQ concentration less than 15 wt %. In terms of thermogravimetric analysis, the organic–inorganic composites displayed improved thermal stability and flame retardancy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1093–1105, 2006