基于铰链式六面顶压机的二级6-8模超高压大腔体内置加热元件的设计与温度标定

 首次报道了一种新型的基于铰链式六面顶压机的二级6-8模大腔体静高压装置的内置加热元件的设计与温度标定。此加热组装结构简单,升温快,保温效果好,并有效地解决了国外基于两面顶压机构架下的二级6-8模内加热组装中热电偶在施加压力时易断的问题。以低成本的碳管为加热元件,采用直接和间接两种加热方式,用双铂铑（Pt6%Rh-Pt30%Rt）B型热电偶进行温度测量,并根据实验过程中加热功率与腔内实际温度的关系,对不同压力下腔体内的温度进行了标定。实验结果表明：此加热系统的油压达到40 MPa（腔体压力约10 GPa）时,温度可以达到1 700 ℃以上;在油压为30 MPa、样品室温度为1 000 ℃时,保温时间可达2 h,甚至更长;实验中获得样品的直径可达3 mm,高度可达7 mm,实现了在高温超高压条件下大样品的制备,满足了实验对产生高温超高压条件的需要。     

Stable edge dislocations in finite crystals

Dislocations have been considered as mechanically unstable defects in bulk crystals, ignoring the Peierls oscillations. Eshelby [J. Appl. Phys. 24 (1953) p.176] had showed that a screw dislocation can be stable in a thin cylinder. In the current work, considering Eshelby's example of an edge dislocation in a single crystalline plate, we show that an edge dislocation can be stable in a finite crystal. Using specific examples, we also show that the position of stability of an edge dislocation can be off-centre. This shift in the stability from the centre marks the transition from a stable dislocation to an unstable one. The above-mentioned tasks are achieved by simulating edge dislocations using the finite element method.     

过模慢波结构频率反射特性及谐振腔的影响

利用有限元方法求解:S-参数矩阵,研究了过模慢波结构对圆波导TM01,TM02模的反射特性,分析了在慢波结构末端加入谐振腔后,由于两端口的不对称性而造成的对反射特性影响。结果表明,在TM01的π模频率附近,慢波结构和谐振腔组成的系统对无谐振腔一侧端口入射TM01模的反射增大,而对有谐振腔一侧端口入射TM01模的反射减小。根据计算结果,解释了普通多波切伦柯夫振荡器所用慢波结构周期数较多的原因,说明了在多波切伦柯夫振荡器中引入谐振腔后,不但可以减少所用慢波结构周期数,而且有利于提高微波输出效率。     

激光对红外系统的失效机理和破坏效应研究

根据红外光学系统的会聚特性,用光学增益方法分析了红外系统中各元件对应的光强分布,确定了位于焦面附近光学元件是激光破坏的易损部件,并提出了强激光对红外系统元件损伤,造成其探测、制导功能失效的硬破坏机理;由红外滤光片、探测器和信号处理电路与入射激光波长的光谱响应分析,提出了弱激光对红外系统干扰,导致其探测、制导功能在激光辐照一段时间内失效的软破坏机理;开展了激光辐照红外系统的失效验证实验,较好地解释了其失效的机理和效应。     

Probenchemische Methode zur Bestimmung von 15N an in Gesteinen fixiertem Stickstoff

Zur Klärung geologischer Prozesse werden in zunchmendem Maße die Isotopenvariationen des Stickstoffs herangezogen. Da der größte Teil des Stickstoffs der Gesteine in gebundener Form als Ammoniumstickstoff [1–6] vorliegt, kommt der Untersuchung der Isotopenvariationen desselben eine große Bedeutung zu.     

Note on the Design Differentiability of the Static Response of Elastic Structures

This paper provides a new proof of design sensitivity of the static response of some typical structures. These structures (beams, plates, and plane elastic solids) have been described previously. A proof of design sensitivity of the inverse state operator was provided there, and design sensitivity of static response was derived. The proof presented here is simpler and self-contained.     

Dislocation density crystalline plasticity modeling of lath martensitic microstructures in steel alloys

A three-dimensional multiple-slip dislocation density-based crystalline formulation, specialized finite-element formulations and Voronoi tessellations adapted to martensitic orientations were used to investigate large strain inelastic deformation modes and dislocation density evolution in martensitic microstructures. The formulation is based on accounting for variant morphologies and orientations, retained austenite and initial dislocation densities that are uniquely inherent to martensitic microstructures. The effects of parent austenite orientation and retained austenite were also investigated for heterogeneous fcc/bcc crystalline structures. Furthermore, the formulation was used to investigate microstructures mapped directly from SEM/EBSD images of martensitic steel alloys. The analysis indicates that variant morphology and orientations have a direct effect on dislocation density accumulation and inelastic localization in martensitic microstructures, and that lath directions, orientations and arrangements are critical characteristics of high strength martensitic deformation and behavior.     

On the usage of NURBS as interface representation in free‐surface flows

When simulating free‐surface flows using the finite element method, there are many cases where the governing equations require information which must be derived from the available discretized geometry. Examples are curvature or normal vectors. The accurate computation of this information directly from the finite element mesh often requires a high degree of refinement—which is not necessarily required to obtain an accurate flow solution. As a remedy and an option to be able to use coarser meshes, the representation of the free surface using non‐uniform rational B‐splines (NURBS) curves or surfaces is investigated in this work. The advantages of a NURBS parameterization in comparison with the standard approach are discussed. In addition, it is explored how the pressure jump resulting from surface tension effects can be handled using doubled interface nodes. Numerical examples include the computation of surface tension in a two‐phase flow as well as the computation of normal vectors as a basis for mesh deformation methods. For these examples, the improvement of the numerical solution compared with the standard approaches on identical meshes is shown. Copyright © 2011 John Wiley & Sons, Ltd.     

Three‐dimensional computation for flow‐induced vibrations in in‐line and cross‐flow directions of a circular cylinder

We present numerical results for in‐line and cross‐flow vibrations of a circular cylinder, which is immersed in a uniform flow and is elastically supported by damper‐spring systems to compute vibrations of a rigid cylinder. In the case of a circular cylinder with a low Scruton number, it is well‐known that two types of self‐excited vibrations appear in the in‐line direction in the range of low reduced velocities. On the other hand, a cross‐flow vibration of the circular cylinder can be excited in the range of high reduced velocities. Therefore, we compute the flow‐induced vibrations of the circular cylinder in the wide range of the reduced velocities at low and high Scruton numbers and discuss about excitation mechanisms in the in‐line and cross‐flow directions. Copyright © 2011 John Wiley & Sons, Ltd.     

A vectorial algorithm with finite element method for prediction of powder segregation in metal injection molding

The design of the mold and the choice of the injection parameters for metal injection molding (MIM) is required to maintain homogeneity of the filled mixture. However, powder segregation is unavoidable in MIM because of the significant difference in densities of the metallic powder and the polymer binder. To achieve an effective prediction of segregation effect, a biphasic model based on mixture theory is employed. The viscous behaviors of each phase and the interaction coefficient between the flows of the two phases should be determined. The solution of two coupled Navier–Stokes equations results in a tremendous computation effort. The previous development of an explicit algorithm makes the biphasic simulation much faster than that of the classic methods. However, it is strongly desired to reduce or even eliminate the numerous global solutions for pressure fields at each time step. Hence, a new vectorial algorithm is proposed and developed to perform the simulation only by vectorial operations. It provides the anticipated efficiency in the simulation of biphasic modeling, and the advantage to use the classic elements of equal‐order interpolations. Some results produced by the two algorithms are compared with the experimental values to validate the new vectorial algorithm. Copyright © 2012 John Wiley & Sons, Ltd.