Semi-quantitative study on the Staebler--Wronski effect of hydrogenated amorphous silicon films prepared with HW-ECR-CVD system

The method of numerical simulation is used to fit the relationship between the photoconductivity in films and the illumination time. The generation and process rule of kinds of different charged defect states during illumination are revealed. It is found surprisingly that the initial photoconductivity determines directly the total account of photoconductivity degradation of sample.     

Preparation and tribological properties of DLC/Ti filmby pulsed laser arc deposition

This paper reports that DLC (diamond like carbon)/Ti and DLC films were prepared by using pulsed laser arc deposition. R-ray diffraction, Auger electron spectroscopy, Raman spectroscopy, atomic force microscopy, nanoindenter, spectroscopic ellipsometer, surface profiler and micro-tribometer were employed to study the structure and tribological properties of DLC/Ti and DLC films. The results show that DLC/Ti film, with $I(D)/I(G)$ 0.28 and corresponding to 76{\%} sp$^{3}$ content calculated by Raman spectroscopy, uniform chemical composition along depth direction, 98 at{\%} content of carbon, hardness 8.2 GPa and Young's modulus 110.5 GPa, compressive stress 6.579 GPa, thickness 46~nm, coefficient of friction 0.08, and critical load 95mN, exhibits excellent mechanical and tribological properties.     

常压化学气相沉积技术生长ZnO:H薄膜的光学性质

采用常压金属有机物化学气相沉积技术(AP-MOCVD),以二乙基锌(DEZn)为Zn源,去离子水(H2O)为氧源,N2作载气,在外延ZnO薄膜的反应气氛中通入少量氢气,在c-Al2O3衬底上生长出了ZnO∶H薄膜。用X射线双晶衍射和光致发光谱对ZnO∶H薄膜的结晶性能和光学性质进行表征。结果表明,ZnO∶H薄膜(002)和(102)面的Ω扫描半峰全宽分别为46.1 mrad和81.4 mrad,表明该薄膜具有良好的结晶性能;室温下,ZnO∶H薄膜具有较强的紫外光发射(380 nm),在低温10 K光致发光谱中观测到位于3.3630 eV处与氢相关的中性施主束缚激子峰(I4)及其位于3.331 eV处的双电子卫星峰(TES)。采用退火的方法,通过观测I4峰的强度变化,研究了氢在ZnO∶H薄膜中的热稳定性。发现随着退火温度的升高,I4峰的强度逐渐减弱,表明在高温下退火,氢会从ZnO薄膜中逸出。     

用锌有机源和CO2/H2混合气源PECVD沉积ZnO薄膜

在等离子体作用下,以CO2/H2混合气为氧源,Zn(C2H5)2锌为锌源,在单晶硅上生长出高度择优取向的氧化锌薄膜。X射线衍射分析表明,薄膜为六方结构,c轴高度择优;原子力显微镜观察到晶粒是有规律地按六方排布,薄膜的表面粗糙度较小;从光致发光谱还发现在380 nm处有非常强的紫外峰。     

Nonpolar a-plane light-emitting diode with an in-situ SiNx interlayer on r-plane sapphire grown by metal-organic chemical vapour deposition

We report on the growth and fabrication of nonpolar a-plane light emitting diodes with an in-situ SiN_x interlayer grown between the undoped a-plane GaN buffer and Si-doped GaN layer. X-ray diffraction shows that the crystalline quality of the GaN buffer layer is greatly improved with the introduction of the SiN_x interlayer. The electrical properties are also improved. For example, electron mobility and sheet resistance are reduced from high resistance to 31.6 cm²/(V·s) and 460 Ω/口 respectively. Owing to the significant effect of the SiN_x interlayer, a-plane LEDs are realized. Electroluminescence of a nonpolar a-plane light-emitting diode with a wavelength of 488nm is demonstrated. The emission peak remains constant when the injection current increases to over 20 mA.     

Characterization of hydrogenated amorphous carbon thin films by end-Hall ion beam deposition

Pure hydrogenated amorphous carbon (α-C:H) and nitrogen doped hydrogenated amorphous carbon (α-C:H:N) thin films were prepared using end-Hall (EH) ion beam deposition with a beam energy ranging from 24 eV to 48 eV. The composition, microstructure and mechanical properties of the films were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, scanning probe microscopy (SPM), and nano-scratch tests. The films are uniform and smooth with root mean square roughness values of 0.5-0.8 nm for α-C:H and 0.35 nm for α-C:H:N films. When the ion energy was increased from 24 eV to 48 eV, the fraction of sp³ bonding in the α-C:H films increased from 36% to 55%, the hardness increased from 8 GPa to 12.5 GPa, and the Young's modulus increased from 100 GPa to 130 GPa. In the α-C:H:N films, N/C atomic ratio, the hardness and Young's modulus of the α-C:H:N films are, 0.087, 15 and 145 GPa, respectively. The results indicate that both higher ion energy and a small amount of N doping improve the mechanical properties of the films. The results have demonstrated that smooth and uniform α-C:H and α-C:H:N films with large area and reasonably high hardness and Young's modulus can be synthesized by EH ion source.     

Dielectric properties of anodic films on sputter-deposited Ti-Si porous columnar films

For electrolytic capacitor application of the single-phase Ti alloys containing supersaturated silicon, which form anodic oxide films with superior dielectric properties, porous Ti-7 at% Si columnar films, as well as Ti columnar films, have been prepared by oblique angle magnetron sputtering on to aluminum substrate with a concave cell structure to enhance the surface area and hence capacitance. The deposited films of both Ti and Ti-7 at% Si have isolated columnar morphology with each column revealing nanogranular texture. The distances between columns are ∼500 nm, corresponding to the cell size of the textured substrate and the gaps between columns are 100-200 nm. When the porous Ti-7 at% Si film is anodized at a constant current density in ammonium pentaborate electrolyte, the growth of a uniform amorphous oxide film continues to ∼35 V, while it is limited to less than 6 V on the porous Ti film. The maximum voltage of the growth of uniform amorphous oxide films on the Ti-7 at% Si films is similar for both the flat and porous columnar films, suggesting little influence of surface roughness on the amorphous-to-crystalline transition of growing anodic oxide under the high electric field. Due to the suppression of crystallization to sufficiently high voltages, the anodic oxide films formed on the porous Ti-7 at% Si film shows markedly improved dielectric properties, in comparison with those on the porous Ti film.     

Structural, optical and electrical properties of Zn1−xCdxO thin films prepared by PLD

Ternary polycrystalline Zn_1−xCd_xO semiconductor films with cadmium content x ranging from 0 to 0.23 were obtained on quartz substrate by pulse laser deposited (PLD) technique. X-ray diffraction measurement revealed that all the films were single phase of wurtzite structure grown on c-axis orientation with its c-axis lattice constant increasing as the Cd content x increasing. Atomic force microscopy observation revealed that the grain size of Zn_1−xCd_xO films decreases continuously as the Cd content x increases. Both photoluminescence and optical measurements showed that the band gap decreases from 3.27 to 2.78 eV with increasing the Cd content x. The increase in Cd content x also leads to the broadening of the emission peak. The resistivity of Zn_1−xCd_xO films decreases evidently for higher values of Cd content x. The shift of PL emission to visible light as well as the decrease of resistivity makes the Zn_1−xCd_xO films potential candidate for optoelectronic device.     

Composition depth profiles of Bi3.15Nd0.85Ti3O12 thin films studied by X-ray photoelectron spectroscopy

In the present work, X-ray photoelectron spectroscopy (XPS) was used to investigate the composition depth profiles of Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) ferroelectric thin film, which was prepared on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD). It is shown that there are three distinct regions formed in BNT film, which are surface layer, bulk film and interface layer. The surface of film is found to consist of one outermost Bi-rich region. High resolution spectra of the O 1s peak in the surface can be decomposed into two components of metallic oxide oxygen and surface adsorbed oxygen. The distribution of component elements is nearly uniform within the bulk film. In the bulk film, high resolution XPS spectra of O 1s, Bi 4f, Nd 3d, Ti 2p are in agreement with the element chemical states of the BNT system. The interfacial layer is formed through the interdiffusion between the BNT film and Pt electrode. In addition, the Ar⁺-ion sputtering changes lots of Bi³⁺ ions into Bi⁰ due to weak Bi-O bond and high etching energy.     

Low-temperature liquid phase deposited TiO2 films on stainless steel for photogenerated cathodic protection applications

The low-temperature synthesis of anatase TiO₂ films was an imperative requirement for their application to corrosion prevention of metals. In this paper, a liquid phase deposition (LPD) technique was developed to prepare TiO₂ films on SUS304 stainless steel (304SS) at a relatively low temperature (80 °C). The as-prepared films were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photon spectroscopy (XPS). It was observed that a dense and crack-free anatase TiO₂ film with a thickness about 300 nm was obtained. The film contained some fluorine and nitrogen elements, and the amounts of these impurities were greatly decreased upon calcination. Under the white light illumination, the electrode potential of TiO₂ coated 304SS rapidly shifted to a more negative direction. Moreover, the photopotential of TiO₂/304SS electrode showed more negative values with increased film thickness. In conclusion, the photogenerated cathodic protection of 304SS was achieved by the low-temperature LPD-derived TiO₂ film.