Monitoring formation of poly(neutral red) film by EQCM

An electrochemical quartz crystal microbalance (EQCM) is employed for monitoring the growth of poly(neutral red) films on platinum in the electrolytic solution containing 5.0 mmol dm⁻³ neutral red, 0.3 mol dm⁻³ H₂SO₄, and 0.5 mol dm⁻³ Na₂SO₄. The in situ measurement of the frequency changes of the EQCM reveals that both the adsorption/desorption of neutral red and the formation of poly(neutral red) film can be observed together with anion sorption/desorption during the redox transformation of the polymer, and that the polymerization rate of neutral red increases slowly before the 11th cycle and then increases quickly with increasing number of potential cycles. Published in Russian in Elektrokhimiya, 2007, Vol. 43, No. 3, pp. 284–289. The text was submitted by the authors in English.     

微波合成铝掺杂钻酸锂材料及性能研究

以LiOH·H2O，Al2O3和Co3O4为原料，微波加热合成Li离子电池正极材料LiAlxCo（1-x）O2．通过XRD测试表征了不同Al加入量时合成产物的晶体结构，确定当x≤0．4时，产物为单一相层状结构．计算了不同x时LiAlxCo（1-x）O2的晶胞参数，随着x的增大，a值减小，c值增大．对合成LiAlxCo（1-x）O2样品进行DSC—TGA测试，结果表明，当x不同时，合成样品的热稳定性不同．SEM测试表明，合成晶体粒度较均匀，粒径在5μm左右．电化学测试表明，LiAl0.2Co0.8O2的电化学性能最好，首次循环放电容量为127mAh／g，多次循环容量损失率小于LiCoO2．     

Shot noise sets the limit of quantification in electrochemical measurements

Detection of single molecules, particles, and rapid redox events is a challenge of electrochemical investigations and requires either an amplification strategy or significant averaging for the electrochemical current to exceed the noise level. We consider the minimum number of electrons required to reach the limit of quantification in these electrochemical measurements. A survey of the literature indicates that the state-of-the-art limit in current detection for different types of measurements (e.g. voltammetry, single-molecule redox cycling, ion channel recordings of single molecules, metal nanoparticle collision, and phase nucleation) is independent of the nature of the measurement and increases linearly with reciprocal response time, Δt^?1, over ～5 orders of magnitude (from ～10 to ～10⁶ s^?1). We demonstrate that the practical limit of quantification requires cumulative measurement of ～2100 electrons during Δt and is determined by statistics of counting electrons, that is, the shot noise in the current.     

Ultra-stable Ni catalysts for methane reforming by carbon dioxide

Methane reforming by carbon dioxide has been studied over ultra-stable Ni catalysts. The catalyst was characterized by XRD, IR and TEM and temperature programmed hydrogenation. The nickel–magnesia solid solution catalyst containing low nickel has shown excellent stability (>3000 h) and no carbon deposition in the methane reforming by carbon dioxide. It was also found that the small nickel metal particle interaction with support surface is effective for the inhibition of carbon formation.     

RESEARCH ON CATALYSTS OF ANTI-CARBON DEPOSITION FOR CH_4 REFORMING WITH CO_2

IntroductionMethaneandcarbondioxidearetWomaincompositionsforthegreenhouseeffectandtheworldglobewanningll].ItisbeneficialtoourlivingenviroIUnenttocontrolthereleaseofthesetwogases.Theconversionofmethanetothecommonfeedstocksynthesisgas(carbonmonoxideandhydro…     

电化学方法获得具有表面增强拉曼活性镍电极的研究

利用纯电化学手段获得了具有较强表面增强拉曼活性的镍电极, 改进了原有的镍电极表面预处理方法. 结果表明, 在0.5 mol/L的NaClO4溶液中, 结合电化学阶跃技术和循环伏安技术, 可以得到合适的粗糙镍电极; 同时, 还得到了探针分子吡啶在该粗糙镍电极表面随电极电位变化的表面增强拉曼光谱(SERS), 此时谱峰强度获得了极大的增强; 还研究了粗糙镍电极的扫描电子显微镜(SEM)图像, 并估算出其SERS增强因子约为104, 此结果比以前的镍电极表面粗糙方法所能达到的增强因子高一个数量级.     

Vanadium Doped Sol-Gel TiO2 Coatings

A study of the experimental conditions required to obtain vanadium doped sol-gel TiO2 coatings is presented. Tetraethyl orthotitanate was employed as the TiO2 source and VCl3, VOSO4 · H2O and VOSO4 dissolved H2SO4 where employed as vanadium sources.Dip coating has been used to produce coatings on silicon wafers, spectral carbon electrodes and titanium electrodes. Both supported and unsupported films have been studied by UV-Vis spectra, IR spectroscopy and X-ray diffraction (XRD). The measurements have been made on samples as prepared and treated thermally at temperatures between 100°C and 300°C. The thermal treatment temperatures have been established from DTA/TGA measurements.The vanadium doped sol-gel TiO2 coatings have been tested as sensors for redox potential measurements in electrochemical processes. The influence of both the thickness of films and the nature of substrate has been investigated.     

Copper ring-disk microelectrodes: fabrication, characterization, and application as an amperometric detector for capillary columns

A novel approach to the fabrication of metal ring-disk (RD) microelectrodes is presented that employs flexible chemical vapor deposition (CVD) and electrode modification techniques. Specifically, the development of a copper ring-disk microelectrode is described utilizing a combination of CVD coating, electroetching, and electroplating. Initially, a 25 μm diameter tungsten wire is concentrically coated by CVD with an insulating layer of silica, a layer of tungsten metal, and finally, a second outer layer of silica. The copper surface was prepared by first creating micrometer cavities by electrochemical etching the tungsten in hydroxide solutions followed by electrodeposition of copper from aqueous solutions of Cu(II). Each step of the process was characterized by scanning electron microscopy, optical microscopy, and cyclic voltammetry, demonstrating the preparation of a viable metal-based dual ring-disk microelectrode system. For the purpose of demonstrating the concept of introducing specific selectivity into the device, amperometric detection of galactose in 0.1 M NaOH was performed at +0.60 V in bulk solution and after flow injection analysis in a capillary column.     

ZnO纳米线的电化学制备研究

High-quality ZnO nanowires have been synthesized at relatively low temperature via one-step electrochemical anodization technique. In this method, Zn sheet acted as the anode and Pb sheet served as the counter electrode, and the complex solution of HF-C₂H₅OH-H₂O was used as electrolyte. ZnO nanowires were characterized by Field Emission Scanning Electron Microscopy (FE-SEM), Transmission Electron Microscopy (TEM) and Selected Area Electron Diffraction (SAED) and X-ray Diffraction (XRD). The results show that the nanowires were wurtzite crystalline ZnO, and the ZnO nanowires with the diameters of 70 nm and 30～40 nm were obtained by adjusting preparation conditions, respectively.     

Chemical modification of polymer surfaces: a review

The main approaches that have been taken to chemically modify polymer surfaces are introduced and reviewed. These are wet chemical oxidation, plasma treatment, classical organic chemistry, and attachment of polymer chains. The extent to which each of these approaches can produce the specific modifications desired is discussed, and any unwanted effects that commonly occur are cited. Finally, the need for using several methods of surface analysis in concert to obtain adequate surface characterization is described.