Thermodynamic derivative properties and densities for hyperbaric gas condensates: SRK equation of state predictions versus Monte Carlo data

The ability of Soave–Redlich–Kwong cubic equation of state (SRK EoS) to predict densities and thermodynamic derivative properties such as thermal expansivity, isothermal compressibility, calorific capacity, and Joule–Thompson coefficients, for two gas condensates over a wide range of pressures (up to 110 MPa) was studied. The predictions of the EoS were compared to Monte Carlo simulation data obtained by Lagache et al. [M.H. Lagache, P. Ungerer, A. Boutin, Fluid Phase Equilibr. 220 (2004) 221]. Two completely different alpha functions for the SRK EoS attractive term were used and their respective effects on the predictions of such properties were analyzed. Also, two different forms of the crossed terms of the attractive parameter, a_ij, and three expressions of the crossed terms of the repulsive parameter, b_ij, were combined in different ways, and predictions were carried out. Little sensitivity of the properties on the chosen alpha function, except for the calorific capacities, was found in the systems studied. The most commonly used combination rules to model phase behavior of reservoir fluids, i.e. geometric and arithmetic forms of a_ij and b_ij, respectively, predicted very deficient results for these fluids at extreme conditions, specially for density calculations.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Magnetic properties of mechanically alloyed Co–Ti powder

An amorphous phase containing traces of non-transformed Co and Ti powders was obtained by mechanical alloying nominal compositions of Co₆₇Ti₃₃ and Co₅₀Ti₅₀ in a high-energy ball-mill. These alloys were prepared from elemental powders of Co and Ti. The heat treatment of Co₆₇Ti₃₃ at 573, 873 and 1173 K crystallized nanoparticles of Co₂Ti and Co₃Ti compounds, while the same treatments conducted on Co₅₀Ti₅₀ resulted in the formation of Co₂Ti and CoTi nanoparticles. The saturation magnetizations reached a maximum value in the amorphous state and they decreased when the temperatures of the heat treatment rose. Demagnetizing interparticle interaction effects were estimated through hysteresis loops and initial magnetization curves using the Fourier technique.     

用三个关系式与Mathematica软件求第二类自然数幂和公式

首先介绍三个第二类自然数幂和关系式并对其中的两式给出证明,接着利用这些关系式与数学软件M athem atica4.0,给出求解第二类自然数幂和公式的若干机械计算方法.     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

Molecular dynamics simulations on the structures and properties of ε-CL-20-based PBXs ——Primary theoretical studies on HEDM formulation design

Five polymer bonded explosives (PBXs) with the base explosive ε-CL-20 (hexanitrohexaazaisowurtzi- tane), the most important high energy density compound (HEDC), and five polymer binders (Estane 5703, GAP, HTPB, PEG, and F2314) were constructed. Molecular dynamics (MD) method was employed to investigate their binding energies (Ebind), compatibility, safety, mechanical properties, and energetic properties. The information and rules were reported for choosing better binders and guiding formula- tion design of high energy density material (HEDM). According to the calculated binding energies, the ordering of compatibility and stability of the five PBXs was predicted as ε-CL-20/PEG > ε-CL-20/ Estane5703 ≈ε-CL-20/GAP > ε-CL-20/HTPB > ε-CL-20/F2314. By pair correlation function g(r) analyses, hydrogen bonds and vdw are found to be the main interactions between the two components. The elasticity and isotropy of PBXs based ε-CL-20 can be obviously improved more than pure ε-CL-20 crystal. It is not by changing the molecular structures of ε-CL-20 for each binder to affect the sensitivity. The safety and energetic properties of these PBXs are mainly influenced by the thermal capability (C°p) and density (ρ) of binders, respectively.     

Performance Analysis for Mobile Ad Hoc Network in Random Graph Models with Spatial Reuse

In this paper,we present a random graph model with spatial reuse for a mobile ad hoc network(MANET) based on the dynamic source routing protocol.Many important performance parameters of theMANET are obtained,such as the average flooding distance (AFD),the probability generating function of theflooding distance,and the probability of a flooding route to be symmetric.Compared with the random graphmodel without spatial reuse,this model is much more effective because it has a smaller value of AFD and alarger probability for finding a symmetric valid route.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003