胶体二硫化钼的高压拉曼散射研究

 测量了平均直径为4 μm的胶体二硫化钼粉剂的高压拉曼光谱。实验结果表明,高压下胶体二硫化钼拉曼峰位随压力增大向高波数方向移动,而峰强随压力增大而减小且峰宽展宽。通过对拉曼峰位移随压力变化的曲线分析,得到了胶体二硫化钼的两个振动模式E¹_2g和A_1g的模式格林爱森常数值。     

胶质液体泡沫(CLA)的形成及其稳定性研究

以研究胶质液体泡沫(CLA)内部结构及其特性为最终目的, 对组成为十二烷基醇聚氧乙烯(3)醚(AEO-3)/正癸烷/十二烷基硫酸钠(SDS)/水的CLA体系形成过程和稳定动力学行为进行了电导率测定和光学显微观察. 通过上述两过程的电导率变化探明了CLA的形成和稳定性动力学行为, 并被光学显微照片所证实. 实验结果表明CLA的形成是一个低能量乳化过程, 经历了水相泡沫化→油相替代气泡乳化→CLA形成. 在整个乳化过程中, 没有发生相的转变现象, CLA呈O/W型乳状液. 其稳定性并不遵守一级动力学模型. 在常温下, 其电导率曲线呈直线关系; 当温度超过318.15 K时, 其电导率曲线近似于Langmuir等温线形. 并可用Sigmoidal模型σ_t=(σ₁－σ₂)/[1＋e^(t－t₀)/S] ＋σ₂较好的拟合, 式中, σ_t表示t 时的电导率值(μS/cm); t表示时间(min); σ₁, σ₂分别代表存储过程中电导率最小值和最大值(μS/cm); t₀对应于σ_t等于 1/2(σ₁＋σ₂)的时间t值(min); S描述了电导率曲线陡峭程度(min). 并提出了CLA的破乳过程包括液膜排液和液膜破裂两个阶段, 同时伴随有絮凝过程发生的稳定性机理.     

Novel filled polymer composites prepared from in situ polymerization via a colloidal approach: II. Blends of kaolin/Nylon-6 in situ composites with conventional Nylon-6 and -66

A novel in situ composite comprised of kaolin clay fillers and polyamide 6 (Nylon-6) was synthesized via a colloidal approach by suspending kaolin particles in aqueous caprolactam and then polymerizing the caprolactam under elevated temperature and pressure. This in situ polymerization technique enables the deposition of nylon molecules directly onto the filler surface. It offers a much larger contact surface area for the nylon molecules to interact with the filler particles and enhances filler/matrix interaction through polymer miscibility. The kaolin particles were shown to be uniformly dispersed in Nylon-6 matrix without appreciable agglomeration. In the highly clay-loaded composites such as the 50/50 kaolin/Nylon-6 in situ composite, the deposited nylon molecules probably form a coated layer on the filler particles. This kind of nylon coated fillers may be applied as a reinforcing entity to commercial Nylon-6 or −;66 by improving particle dispersion and melt processability. The 50/50 kaolin/Nylon-6 in situ composites have been used as a masterbatch for blending with commercial Nylon-6 and Nylon-66 to take advantage of their good properties and to reduce cost. Rheology and mechanical properties of the masterbatch/nylon composites have been investigated in comparison with those of the conventional melt-mixed composites. The improvement of rheological and mechanical properties of the in situ composites has been discussed in relation to the composite structure. © 1996 John Wiley & Sons, Inc.     

Novel filled polymer composites prepared from in situ polymerization via a colloidal approach: I. Kaolin/Nylon-6 in situ composites

A mineral-filled in situ composite was prepared by a colloidal approach by first suspending kaolin filler particles in aqueous caprolactam, and then polymerizing caprolactam in situ at high pressure and temperature. The purpose of this colloidal in situ polymerization is to improve particle dispersion and to enhance interaction of the filler to the polymer matrix. X-ray diffraction studies of the in situ kaolin/Nylon-6 composites revealed that the x-ray peak corresponding to the α-crystal form of Nylon-6 diminished with increasing kaolin loading, while the γ-crystal structure became more pronounced. The degree of crystallinity of Nylon-6 remained fairly unchanged with the kaolin loading level in the in situ composites. Calorimetric and dynamic mechanical studies exhibited that the glass transition temperature of the resulting composite increased significantly with increase in kaolin concentration, suggesting strong filler-matrix interaction at the kaolin/Nylon-6 interface. Scanning electron microscopic (SEM) results showed uniform filler dispersion in the in situ composites relative to the conventional melt-mixed composites. Modulus and tensile strength of these in situ composites were found to be distinctively higher than that of the conventional melt-mixed kaolin/Nylon-6 composites. However, as typical for composite materials, drawability and fracture toughness decreased with increasing kaolin loading. © 1996 John Wiley & Sons, Inc.     

基于二氧化硅胶体晶体薄膜和反射干涉光谱的蛋白冠监测方法

生物分子与纳米材料作用形成的"蛋白冠"影响纳米材料的物理和化学性质,目前缺少有效的原位实时技术监测蛋白冠的形成过程.本研究基于二氧化硅胶体晶体薄膜和反射干涉光谱法,研究了三种代表性血液蛋白质在二氧化硅纳米粒子表面的蛋白冠形成过程,结果表明这三种蛋白具有不同的蛋白冠形成过程及参数;研究了人血清白蛋白在三种表面曲率的二氧化...     

纳米悬浮液热导率测量及其预测模型的探讨

纳米颗粒悬浮液具有广泛应用于强化传热的潜在优势。本文采用加入表面活性剂的方法提高纳米悬浮液的悬浮稳定性,并用瞬态热线法测量了热导率。在分析现有理论模型和纳米悬浮液热导率影响因素研究的基础上,从弹性传动和非弹性传动两方面分析了纳米尺度效应导致纳米悬浮液热导率提高的机理。发现已有的理论公式仍然存在一定欠缺,预测值比实验值偏低,有关机理尚有待于深入探讨。     

Cation identity dependence of crown ether photonic crystal Pb<Superscript>2+</Superscript> sensing

We quantitatively modeled the volume phase transition of a hydrogel containing a crystalline colloidal array with a crown ether ligand which binds Pb²⁺. The hydrogel volume response and the wavelength diffracted depend on the Pb²⁺ concentration and on both the ionic strength and the valence of the nonbinding ionic species. We successfully modeled the response of this hydrogel Pb²⁺ sensor to ionic strength and the cation valence of the added salts. Figure Cation identity dependence of crown ether photonic crystal Pb⁺ sensing     

基于甲基苯丙胺和吗啡的胶体金免疫层析试剂盒检测法的可靠性评价

通过固相萃取-液相色谱-多级质谱(SPE-LC-MS/MS)联用技术和毒品胶体金免疫层析试剂盒检测法对13种中药及调味品样品中甲基苯丙胺及吗啡分别进行定量分析,依据LC-MS/MS检测结果,对毒品胶体金免疫层析试剂盒检测法进行可靠性评价。实验结果表明:型号1试剂盒对甲基苯丙胺和吗啡的特异性均不高,检测准确率分别为57.7%与78.8%;型号2试剂盒对甲基苯丙胺的特异性不足,准确率为73.1%,但对吗啡的检测准确率达到100%。在利用毒品胶体金免疫层析试剂盒进行毒品快速筛查时,应注重排除干扰因素以提高免疫胶体金层析试剂盒的检测准确度。     

基于分子催化剂光驱动水氧化器件的研究进展

光解水制氢是人们解决未来能源危机的一种重要构想,构建高效的光电化学池是实现这一构想的重要途径,而光驱动水氧化的顺利进行是实现这一过程的关键.本文总结了近年来基于分子催化剂及染料敏化的光驱动水氧化分子器件的研究和进展,介绍了这些分子器件的组装和性能研究等,并根据这些研究的优点和不足提出一些浅见.     

胶体金修饰电极测定鱼样中组胺的方法研究

基于胶体金修饰的玻碳电极,利用电流～时间曲线法建立了一种简便、灵敏的组胺检测方法。优化了底液的pH值和组胺的电化学测试方法及条件,考察了修饰电极的电化学性能。结果表明,组胺在胶体金修饰电极上的响应电流(-I,μA)与其浓度(c,μmol/L)在0. 1～64μmol/L范围内呈良好的线性关系,检出限为0. 033μmol/L,在带鱼和黄花鱼样品中的加标回收率分别为94. 4%～106%、91. 8%～106%,相对标准偏差分别为3. 2%、2. 5%。该法操作简单、检测速度快、成本低,适用于带鱼和黄花鱼等鱼样中组胺的测定。