光指针式微小位移测量仪

光指针式微小位移测量仪巧用光路将微小的位移量放大,从光指针终端的标度盘上可以直接读取实际的位移数值.     

基于视觉测量的飞行器舵面角位移传感器标定

提出一种基于计算机单目视觉的飞行器副翼、襟翼、方向舵和升降舵角位移传感器的非接触标定方法.用共面的两个特征圆组成一标定靶固定在飞行器舵面上,用一台定焦数码摄像机对标定靶拍照,获得特征圆数字图像.经图像分析确定特征圆圆心及直径在像面上的透视投影位置和长度,根据透视投影逆变换原理建立物和像空间坐标关系的解算模型,进而导出靶面平面方程.飞行器舵面角位移则由标定靶面的法线方向余弦来表示.仿真结果表明,该方法具有标定过程快速、简单和准确的特点.不需事先标定摄像机内外部参量,其标定准确度优于0.2°.     

Stage-I fatigue crack studies in order to validate the dislocation-free zone model of fracture for bulk materials

Stage-I fatigue cracks are commonly described by the model of Bilby, Cottrell and Swinden (BCS model). However, since several experimental investigations have shown a dislocation-free zone (DFZ) in front of crack-tips, it is necessary to validate the new DFZ model and to examine the deviations to the BCS model. Therefore, the dislocation density distribution is derived from height profiles of slip lines in front of stage-I fatigue cracks in CMSX4® single crystals measured by contact-mode atomic force microscopy. This is possible, because the cracks are initiated at notches milled by focused ion beam technique directly on slip planes with a high Schmid factor. Consequently, the directions of the Burgers vectors are well known; it is possible to calculate the dislocation density distributions from the height profiles. The measured distributions are compared to the calculated distribution function of the DFZ model proposed by Chang et al. The additionally measured microscopic friction stress of the dislocations is then used to calculate the influence of grain boundaries on the dislocation density distribution in front of stage-I cracks. The calculation is done by the extended DFZ model of Shiue et al. and compared with the measured distribution function in polycrystalline specimens. Finally, the crack-tip sliding displacement as a measure for the crack propagation rate is compared for the DFZ model and the BCS model with the experimentally revealed values. The important result: the often used BCS model does not reflect the experimental measurements. On the contrary, the DFZ model reflects the measurements at stage-I cracks qualitatively and quantitatively.     

基于单帧变形条纹的物体三维位移和速度测量

用隔行扫描摄像机采集到的运动物体单帧变形条纹测量三维位移和速度.该方法将一帧变形条纹分成两个单场,利用傅里叶变换轮廓术重建三维面形,从单场条纹的调制度中提取二值化模板,计算质心获得亚像素匹配定位点,通过双三次插值和标定,实现了一个场周期时间内三个维度上的位移和平均速度的测量.匀速运动物体实验结果表明:被测速度的最大绝对误差为0.6 mm/s,相对误差为0.57%.该方法仅用一帧变形条纹即可测量运动物体的三维位移和速度,提高了时间分辨率和测量准确度.     

平行光路方向运动的光栅多普勒效应及其在测微小位移中的应用

研究了光栅平行光路运动时产生的光的多普勒效应,用实验进行了验证,并将该原理应用到对微小位移量的检测中. 对原理进行了拓展,得到光栅以任意角度运动产生光的频移的普适公式.     

Isolation,Detection, and Antigen‐Based Profiling of Circulating Tumor Cells Using a Size‐Dictated Immunocapture Chip

Even though the diagnostic and prognostic value of circulating tumor cells (CTCs) has been demonstrated, their clinical utility and widespread adoption have been limited. Herein, we describe a new device, size‐dictated immunocapture chip (SDI‐Chip), for efficient, sensitive, and spatially resolved capture and detection of CTCs. SDI‐Chip enables selective, frequent, and extended interaction of CTCs with hydrodynamically optimized immunocoated micropillar surfaces. CTCs with different antigen expression levels can be efficiently captured and spatially resolved around the micropillars. Capture efficiency greater than 92 % with a purity of 82 % was achieved with blood samples. CTCs were detected in non‐metastasis colorectal (CRC) patients, while none was detected from healthy volunteers. We believe that SDI‐Chip will facilitate the transition of tumor diagnosis from anatomical pathology to molecular pathology in localized CRC patients.     

The boundedness and asymptotic behavior of solutions of differential system of second-order with variable coefficients

In this paper, the differential system of second-order withvariable coefficients is studied. and some criteria of theboundedness and asymptotic behavior for solutions are given.Consider a system of differential equationsdx_1/dt=p_(11)(t)x_1 p_(12)(t)x_2dx_2/dt=p_(21)(t)x_1 p_(22)(t)x_2Now we studg the boundedness and asymptotic behavior of its so-lutions. In the case of Pij(t)being periodic functions. it wasinvestigated by Burdina; in the case of Pij(t) being arbitraryfunctions. it has not been investigated yet. Besides. the me-thod used by Burdina is only oppropriate for the former but notfor the latter case. In this paper we shall give a method whichis appropriate for both cases.     

反相液相色谱中同系物保留过程中的等焓点

依据液相色谱中溶质计量置换保留模型,从理论上分别推导了出在反相高效订色谱（ＲＰＬＣ）中同系物端基和重复结构单元对Ｚ（１ｍｏｌ溶剂化溶质被固定相吸附时,在其接触表面释放出溶剂的摩尔总数）与绝对温度倒数间的线性关系式。也从分子结构参数推荐导出了同系物端基对总变的贡献△Ｈ,和同系物非端基（或键长）对总焓变的贡献△ＨｓＮｃ的表达式。从而建立了等焓点的坐标方程,阐明了等点的纵坐标相是溶质在等点处的变为零,等     

岩土工程位移时间序列的组合预测研究

将组合预测方法用于岩土工程位移时间序列预测.结合实际观测数据,分别建立位移时间序列预测的GM(1,1)模型、Verhulst模型和趋势曲线模型.采用极小误差法确定各单一模型的权重,建立组合预测模型.应用表明,组合预测的精度高,为岩土工程位移预测提供了一种实用、可靠的方法.     

内部压力作用下矩形板中源于椭圆孔的分支裂纹应力强度因子的一种数值分析

应用一种边界元方法来研究内部压力作用下矩形板中源于椭圆孔的分支裂纹。该边界元方法由Crouch与Starfied建立的常位移不连续单元和笔者最近提出的裂尖位移不连续单元构成。在该边界元方法的实施过程中,左、右裂尖位移不连续单元分别置于裂纹的左、右裂尖处,而常位移不连续单元则分布于除了裂尖位移不连续单元占据的位置之外的整个裂纹面及其它边界。本数值结果进一步证实这种数值方法对计算有限大板中复杂裂纹的应力强度因子的有效性,同时该数值结果可以揭示裂纹体几何对应力强度因子的影响。