自由曲面光学虚拟制造与检测系统的探讨

自由曲面光学产品设计、制造与检测的工艺流程，通常采取试凑法逐次逼近。由于加工 检测 再加工，循环往复，既费时，成本又高，产生了瓶颈问题。为了解决此弊端，本文运用虚拟制造技术，提出光学虚拟制造的基本构想，即虚拟制造系统结构模型，给出光学系统虚拟原型的构成和光学系统成像质量虚拟检测系统的构成，讨论光学成像质量的仿真检测以及敏度分析方法。研究结果表明：运用虚拟制造与检测技术，可缩短研发周期，降低成本，优化工艺并提高产品质量。     

圆感应同步器数显表检测方法研究

介绍了圆感应同步器数显表测角系统的工作原理,以及在静态和动态测角方法。提出了两种提高动态测量精度的方法。实验数据验证了方法的合理性。     

Extension of the range of resonator scanning spectrometer into submillimeter band and some perspectives of its further developments

Extension of the working frequency of modern resonator spectrometers into submillimeter wave range is described. Experimental record of atmospheric absorption spectrum covering 45-370 GHz range is demonstrated for the first time, and measured water vapor J′_{ka′, kc′}-J_{ka, kc} = 5_1,5-4_2,2 at 325 GHz line parameters are presented. For the first time pressure lineshift for the 325-GHz water vapor line is measured. Further extension of working range is discussed. New estimations of physical limits of time needed for measurements of absorption in the whole Backward Wave Oscillator (BWO) range are given for phase continuous synthesizer regime. Basic schemes of fast broadband continuous phase synthesized sources are discussed. Verification of the previous measurements of water vapor 3_1,3-2_2,0 at 183 GHz line parameters is presented. Comparisons with ringdown resonator spectrometers are given.     

A new microtensile tester for the study of MEMS materials with the aid of atomic force microscopy

An apparatus has been designed and implemented to measure the elastic tensile properties (Young's modulus and tensile strength) of surface micromachined polysilicon specimens. The tensile specimens are “dog-bone” shaped ending in a large “paddle” for convenient electrostatic or, in the improved apparatus, ultraviolet (UV) light curable adhesive gripping deposited with electrostatically controlled manipulation. The typical test section of the specimens is 400 μm long with 2 μm×50 μm cross section. The new device supports a nanomechanics method developed in our laboratory to acquire surface topologies of deforming specimens by means of Atomic Force Microscopy (AFM) to determine (fields of) strains via Digital Image Correlation (DIC). With this tool, high strength or non-linearly behaving materials can be tested under different environmental conditions by measuring the strains directly on the surface of the film with nanometer resolution.     

金刚石窗口冷却Yb3+∶YAG DPSSL设计

针对高功率二极管重复率抽运的V型非稳腔Yb3+∶YAG激光头，提出了利用金刚石窗口冷却和直接水冷相结合的复合冷却设计.在YAG片的抽运面进行直接水冷，同时在激光提取面利用金刚石窗口冷却介质.金刚石优异的导热性能不仅能够有效地冷却激光介质，还能消除横向的温度梯度，解决了高功率激光器冷却和高功率抽运的矛盾.模拟结果表明对掺杂10 at %厚度为1.6 mm的Yb3+∶YAG片在抽运功率密度为20 kW/cm2，重复频率为10 Hz的条件下，要将最高温度控制在可接受的范围内（比如320 K），周围冷却水的对流换热系数约为4000 W/m2K.     

数值孔径与数字剪切散斑干涉条纹亮度的关系

分析了数字剪切散斑干涉条纹图的形成理论，并获得了条纹亮度与摄象机数值孔径等参数的精确关系式，从理论分析和实验验证均得出在采用小的摄象机数值孔径和３ｍＷ Ｈｅ－Ｎｅ激光器的情况下，仍可获得比较满意的数字剪切散斑干涉条纹图，理论工作及其结论对于进行数字剪切散斑干涉实验的最佳参数选择具有指导作用。     

基于变芯径光纤的光学系统在光造型中的应用

光学系统采用变芯径光纤，可大幅度提高光的传输效率，增加光学子系统柔性。描述了光造型工作原理及其理论依据，在介绍所研制的光的成型系统光学子系统的基础上，阐述了紫外光源的选择与设计，及变芯径光纤的设计、传输、耦合与聚焦等技术。该套基于变芯径光纤的光学子系统成本低、体积小、效率高，巳成功应用于所研制的台式低成本快速成型系统中，为该系统的进一步推广奠定了技术基础。     

基于TMS320C5410EVM板的IIR数字滤波器的设计

本文研究DSP中的IIR数字滤波器的原理和用MATLAB在TMS320C5410EVM中设计IIR数字滤波器的过程和设计方法以及程序的调试方法。     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang