A density functional theory computational study of the role of ligand on the stability of CuI and CuII species associated with ATRP and SET‐LRP

Atom transfer radical polymerization (ATRP) and single electron‐transfer living radical polymerization (SET‐LRP) both utilize copper complexes of various oxidation states with N‐ligands to perform their respective activation and deactivation steps. Herein, we utilize DFT (B3YLP) methods to determine the preferred ligand‐binding geometries for Cu/N‐ligand complexes related to ATRP and SET‐LRP. We find that those ligands capable of achieving tetrahedral complexes with Cu^I and trigonal bipyramidal with axial halide complexes with [Cu^IIX]⁺ have higher energies of stabilization. We were able to correlate calculated preferential stabilization of [Cu^IIX]⁺ with those ligands that perform best in SET‐LRP. A crude calculation of energy of disproportionation revealed that the same preferential binding of [Cu^IIX]⁺ results in increased propensity for disproportionation. Finally, by examining the relative energies of the basic steps of ATRP and SET‐LRP, we were able to rationalize the transition from the ATRP mechanism to the SET‐LRP mechanism as we transition from typical nonpolar ATRP solvents to polar SET‐LRP solvents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4950–4964, 2007     

Tuning size and catalytic activity of nano-clusters of cobalt oxide

Cobalt oxides were prepared by three different methods: (1) by reacting cobalt nitrate with oxalic acid, (2) co-precipitating cobalt nitrate with sodium carbonate, and (3) using sodium dodecyl sulphate as organic surfactant. All three samples were characterized before and after calcination by solvent extraction and the resulting products examined by IR spectroscopy. In the case of method 3, the removal of surfactant was followed by TGA studies. Products from all three methods were identified by XRD. Peaks in low angle XRD indicate the porous nature of the oxides. The morphology of the pores was studied by transmission electron microscopy. Some irregular pore structures were obtained for samples from methods 1 and 2, with an average size of 4–6 nm. Only the product from method 3 using SDS as template showed ordered structure and optimum size, and Brunauer-Emmet-Teller surface areas of the as-prepared, as well as the treated samples, exhibited H3 type hysteresis. The samples from the three methods were used as catalysts in the oxidation reaction of cyclohexane under mild conditions and the catalytic efficiency of the cobalt oxide was comparable with mesoporous cobalt oxides.     

Orientation and relaxation of polymer–clay solutions studied by rheology and small-angle neutron scattering

The influence of shear on viscoelastic solutions of poly(ethylene oxide) (PEO) and clay [montmorillonite, i.e., Cloisite NA+ (CNA)] was investigated with rheology and small-angle neutron scattering (SANS). The steady-state viscosity and SANS were used to measure the shear-induced orientation and relaxation of the polymer and clay platelets. Anisotropic scattering patterns developed at much lower shear rates than in pure clay solutions. The scattering anisotropy saturated at low shear rates, and the CNA clay platelets aligned with the flow, with the surface normal parallel to the gradient direction. The cessation of shear led to partial and slow randomization of the CNA platelets, whereas extremely fast relaxation was observed for laponite (LRD) platelets. These PEO–CNA networklike solutions were compared with previously reported PEO–LRD networks, and the differences and similarities, with respect to the shear orientation, relaxation, and polymer–clay interactions, were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3102–3112, 2004     

Thermal characterisation of micro-hotplates used in sensor structures

Micro-hotplates operated at elevated temperature form the basic element in several sensor devices, such as integrated calorimetric or Taguchi-type gas sensors and flow-rate sensors. In all of these applications thermal properties of the sensing elements play a determining role in functional operation, therefore, their accurate characterisation is essential. The micro-hotplates investigated were developed by one side porous silicon micro-machining technology, forming Pt micro-filaments embedded in non-stoichiometric silicon nitride, and suspended across a cavity. This work is dealing with the accurate temperature detection in the micro-scale by different measurement methods for the deduction of steady state and transient thermal properties from the results. Transient properties of the structure were investigated by application of a simplified thermal equivalent circuit model.     

Analysis of a demodulation system for Fiber Bragg Grating sensors using two fixed filters

The analysis of a demodulation system for Fiber Bragg Grating sensors based on two fixed spectral filters has been carried out both theoretically and experimentally. Different system configurations were analyzed by modifying the spectral position of the filters as well as the optical power-level of the signal reaching the two photo-detectors. Measurements with integration times that varied from 0.01 to 1 s have been compared with the low-frequency limit predicted for long-term operation. Comparisons between simulated and experimental results show good agreement, and extrapolations indicate that it should be possible to achieve an operating spectrum range of the order of 7 nm, with uncertainties equivalent to less than 2 pm in measurements of the sensor peak position.     

Thickness of a silica-tethered poly(ethylene oxide) layer measured by spin labeling

EPR spectroscopy of labeled poly(ethylene oxide) (PEO) grafted on silica has been used to characterize the conformation and local dynamics of the chains. Grafted molecules of MW 2000 with grafting ratios of 0.045, 0.057, 0.126, and 0.42 molecules/nm² were in contact with benzene. The mobility of the label was compared with that observed for solution of PEO from very diluted to highly concentrated and even bulk PEO. Thus, the concentration inside the grafted layer could be evaluated and also the thickness, which evolves rather linearly with the grafting ratio. © 1995 John Wiley & Sons, Inc.     

A comparative XPS and UPS study of VOx layers on mineral TiO2(001)‐anatase supports

Four vanadium oxide layers on mineral TiO₂(001)‐anatase supports with different thickness (3–33 Å) were prepared with reactive d.c. magnetron sputtering and were extensively studied with photoelectron spectroscopy. Al Kα radiation and 150 eV synchrotron radiation were used as excitation sources. The evolution of the 2p, 3s and 3p core level line shapes of V and Ti as a function of the vanadium oxide thickness was studied, as well as the O1s and O2s core lines and the valence band. All the V2p spectra of the deposited vanadium oxide layers consist of at least 60% V⁵⁺, the rest being V⁴⁺. The V3p region is complicated by multiplet splitting, which prevents the determination of the vanadium oxidation state. The V3p multiplet splitting is different for the two excitation energies. No reduction of the titania support surface due to the vanadium oxide deposition was observed. Copyright © 2006 John Wiley & Sons, Ltd.     

Correct Evaluation of the Effect of Transverse Effective Charges on Phonons in AlAs Quantum Dots

An improved valence force field model (VFFM) is suggested to calculate the phonon modes in both bulk specimens and quantum dots (QDs) of AlAs taking account of the effect of transverse effective charges (TCs) correctly.The resultant dispersions of AlAs bulk phonons are in accord better with the results carefully fitted to the experimental data by using 11-parameters rigid-ion model, than those got by ordinary VFFM, especially in the region of near F point. For AlAs QDs, TCs are evaluated bond by bond for each phonon mode of QD and its effect on the change of the force on atoms is taken into account to modify further the phonon spectrum. The frequency spectra and densities of phonon states of different irreducible representations calculated by using improved VFFM are compared with the results of ordinary VFFM. The correct evaluation of the TCs is not only important in calculating the phonon spectrum of both bulk and QD specimens accurately, but is also in the further discussion of the electron-phonon (e-ph) interaction, which can be directly related to TCs of ions in QD.     

荧光光纤温度传感器激励光源的选择

本文分析计算了荧光光纤温度传感器的温敏元件——GsAlAs/GaAs双异质结半导体材料的荧光辐射效率与激励光波长的关系。讨论了温度测量范围及温敏元件GaAlAs层铝含量对激励光源的限制,在0～200℃测温范围内,若采用LED作激励光源,其峰值波长应在0.70～0.76μm之间选择。     

Heterograft copolymers of poly(ε‐caprolactone) prepared by combination of ATRA “grafting onto” and ATRP “grafting from” processes

This paper aims at reporting on the synthesis of a heterograft copolymer by combining the “grafting onto” process based on atom transfer radical addition (ATRA) and the “grafting from” process by atom transfer radical polymerization (ATRP). The statistical copolymerization of ε‐caprolactone (εCL) and α‐chloro‐ε‐caprolactone (αClεCL) was initiated by 2,2‐dibutyl‐2‐stanna‐1,3‐dioxepane (DSDOP), followed by ATRA of parts of the chlorinated units of poly(αClεCL‐co‐εCL) on the terminal double bond of α‐MeO,ω‐CH₂?CH? CH₂? CO₂‐poly(ethylene oxide) (PEO). The amphiphilic poly(εCL‐g‐EO) graft copolymer collected at this stage forms micelles as supported by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The unreacted pendant chloro groups of poly(εCL‐g‐EO) were used to initiate the ATRP of styrene with formation of copolymer with two populations of randomly distributed grafts, that is PEO and polystyrene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6015–6024, 2006