基于甲醇化学链燃烧的新型燃气轮机间冷循环

本文提出一种新颖的甲醇化学链燃烧动力循环系统.该系统利用空气压缩的间冷热提供甲醇和Fe2O3反应热,将间冷的低温热转换为高品位化学能;同时得到预冷的空气吸收燃烧产物Fe2O3的显热,降低了还原反应的温度.与常规化学链循环相比,该循环利用间冷的热量代替高温Fe2O3的显热提供还原反应的反应热,系统内能量品位匹配更加合理.根据图像(火用)分析方法,阐明了甲醇化学链燃烧过程(火用)损失减少和间冷热品位提升的机理.本文对新循环进行了分析,并以常规化学链循环为参照,研究了其性能.新循环的效率较高,同时可以实现CO2无能耗的分离.     

Effect of the laser fluence on the surface characterization of β-FeSi2 films prepared by pulsed laser deposition

Single-phase β-FeSi₂ films on silicon (1 0 0) were fabricated by pulse laser deposition. The structure and crystal quality of the samples were characterized by X-ray diffraction and Fourier transform infrared spectroscopy. The field scanning electron microscopy showed that the film thickness increases with the increasing of the laser fluence. Moreover, atomic force microscopy observations revealed the changes of surface properties with different laser fluence. Based upon all experimental results, it is found that 7 J/cm² is the most favorable for the formation of β-FeSi₂ thin films.     

Characterization and oxidation behavior of NiCoCrAlY coating fabricated by electrophoretic deposition and vacuum heat treatment

Electrophoretic deposition (EPD) was showed to be a feasible and convenient method to fabricate NiCoCrAlY coatings on nickel based supperalloys. The microstructure and composition of the NiCoCrAlY coatings after vacuum heat treatment were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDAX). Isothermal-oxidation test was performed at 1100 °C in static air for 100 h. The results show that the major phases in electrophoretic deposited and vacuum heat treated NiCoCrAlY coating are γ-Ni and γ′-Ni₃Al phases, also there is an extremely small quantity of Al₂O₃ in the coating. Composition fluctuations occur in the coating and a certain amount of titanium diffuse from the superalloy substrate to the top of the coating during vacuum heat treatment. The oxidation test results exhibit that the oxidation kinetics of this coating has two typical stages. The protective oxide layer is mainly formed in the initial linear growth stage and then the oxide layer hinders further oxidation of the coating in the subsequent parabolic growth stage. The coating can effectively protect the superalloy substrate from oxidation. A certain amount of rutile TiO₂ is formed in the coating during oxidation and it is adverse to the oxidation resistance of the coating.     

Low-temperature liquid phase deposited TiO2 films on stainless steel for photogenerated cathodic protection applications

The low-temperature synthesis of anatase TiO₂ films was an imperative requirement for their application to corrosion prevention of metals. In this paper, a liquid phase deposition (LPD) technique was developed to prepare TiO₂ films on SUS304 stainless steel (304SS) at a relatively low temperature (80 °C). The as-prepared films were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photon spectroscopy (XPS). It was observed that a dense and crack-free anatase TiO₂ film with a thickness about 300 nm was obtained. The film contained some fluorine and nitrogen elements, and the amounts of these impurities were greatly decreased upon calcination. Under the white light illumination, the electrode potential of TiO₂ coated 304SS rapidly shifted to a more negative direction. Moreover, the photopotential of TiO₂/304SS electrode showed more negative values with increased film thickness. In conclusion, the photogenerated cathodic protection of 304SS was achieved by the low-temperature LPD-derived TiO₂ film.     

Zirconium-assisted reaction in low temperature atomic layer deposition using Bis(ethyl-methyl-amino)silane and water

The reaction of Bis(ethyl-methyl-amino)silane (BEMAS) and water in atomic layer deposition (ALD) became possible when Zr-containing species were adsorbed on the vacant sites of the surface after a pulse and purge of BEMAS. The growth rates of the Si(Zr)O_x films were 0.8-0.9 nm/cycle in the temperature range of 185-325 °C. This phenomenon probably originates from the highly reactive hydroxyl species generated by Zr atoms. From this point of view, transition metals make reactant gas molecules to be highly activated in the ALD processes of transition metal oxides and nitrides, which might be an important factor that determines the ALD characteristics.     

Peptide-induced patterning of gold nanoparticle thin films

In this work, the use of patterned proteins and peptides for the deposition of gold nanoparticles on several substrates with different surface chemistries is presented. The patterned biomolecule on the surface acts as a catalyst to precipitate gold nanoparticles from a precursor solution of HAuCl₄ onto the substrate. The peptide patterning on the surfaces was accomplished by physical adsorption or covalent attachment. It was shown that by using covalent attachment with a linker molecule, the influence of the surface properties from the different substrates on the biomolecule adsorption and subsequent nanoparticle deposition could be avoided. By adjusting the reaction conditions such as pH or HAuCl₄ concentration, the sizes and morphologies of deposited gold nanoparticle agglomerates could be controlled. Two biomolecules were used for this experiment, 3XFLAG peptide and bovine serum albumin (BSA). A micro-transfer molding technique was used to pattern the peptides on the substrates, in which a pre-patterned poly(dimethylsiloxane) (PDMS) mold was used to deposit a lift-off pattern of polypropylmethacrylate (PPMA) on the various substrates. The proteins were either physically adsorbed or covalently attached to the substrates, and an aqueous HAuCl₄ solution was applied on the substrates with the protein micropatterns, causing the precipitation of gold nanoparticles onto the patterns. SEM, AFM, and Electron Beam Induced Current (EBIC) were used for characterization.     

Influence of NH beam bombarding energy on structural characterization and cell attachment of CNx coating

The carbon nitride (CN_x) coating with its novel properties will be excellent candidate for biomedical applications. CN_x coatings were prepared on the surface of Ti–6Al–4V by ion-beam-assisted deposition (IBAD) with different NHⁿ⁺ beam bombarding energies at low substrate temperature. The coatings were characterized by Scanning electron microscopy (SEM), Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and Fourier-transform infrared (FTIR) spectroscopy. The result showed that the wear-resistance of CN_x coatings was better at higher beam bombarding energy. The cell attachment tests also gave interesting results that CN_x coatings exhibited low macrophage attachment and provide desirable surface for the normal cellular growth and morphology of the fibroblasts. Structural analysis showed that NHⁿ⁺ beam bombardment at the energies of 300–400 eV could result in more nitrogen concentration and fraction of sp³CN bonds in the structure of CN_x coatings, which may be responsible for the improvement in the wear-resistance and the cell attachment.     

Preparation and characterization of the LiInSe2 thin films

Summary p-type LiInSe₂ films have been prepared by the rapid evaporation method onn-type Si andn-type GaP. Various characterization techniques such as the X-ray analysis, the Rutherford backscattering (RBS) analysis and the scanning electron microscopy were used to evaluated the quality of the films. The rectifications of the preliminary heterojunctions are demonstrated. Paper presented at the ?V International Conference on Ternary and Multinary Compounds?, held in Cagliari, September 14–16, 1982.     

Determination of Easy Axis in a Chemical Ferromagnet, 4-(p-Chlorobenzylideneamino)–TEMPO (TEMPO=2,2,6,6-Tetramethylpiperidin-1-Oxyl)

The trapping sites for muon and muonium in ferromagnetic p-Cl–Ph–CH=N–TEMPO [(4-(p-chlorobenzylideneamino)–TEMPO (TEMPO = 2,6,6-tetramethyl-piperidin-1-yloxyl)] and the hyperfine interaction tensors for these sites are obtained using first-principles Unrestricted Hartree–Fock theory. The calculated hyperfine interactions are used to compare the calculated zero field muon spin rotation (μSR) frequencies for different choices for the easy axis and the observed frequency. It has been concluded that the two trapping centers that can best explain the observed μSR frequency are a trapped singlet muonium near the radical oxygen and a trapped muon site near the chlorine. The direction of the easy axis also is determined to be the b-axis of the monoclinic lattice. This direction for the easy axis is confirmed by determining the direction of the distributed magnetization in the molecular solid which leads to a minimum dipole–dipole interaction energy. The consequences of this agreement for the easy axis direction by two independent procedures are discussed. This revised version was published online in September 2006 with corrections to the Cover Date.     

低能离子对酪氨酸溶液损伤作用的光谱研究初报

利用气体我放电产生低能离子,其在放电间隙的电场加速下撞击水溶液样品。了低能离子作用后酪氨酸溶液的紫外及红外吸收光谱的变化。结果表明,气体放电产生的离子对Ｔｙｒ造成了多种损伤。不仅使化学键断裂,分子解体,而且外来的活性离子会与溶液中的元素形成新的化学基团,妆在受损伤分子碎片上组成新的损伤物质,充分体现了低能离子与物质相互作用的“离子沉积”效应。