Ti6A14V表面微弧氧化陶瓷涂层的结构和摩擦学特性

采用交流微弧氧化法，在Na2SiO3-(NaPO3)6-Na3MoO4溶液中制备了Ti6A14V表面氧化物陶瓷涂层，用X射线衍射仪、扫描电子显微镜和球-盘摩擦磨损试验机研究了涂层的结构、形貌及摩擦学性能，用纳米压痕仪测定了涂层致密层的硬度，用扫描电子显微镜观察涂层磨损表面形貌，用能谱仪分析涂层磨屑的元素组成．结果表明：厚约20pm的涂层致密均匀，主要由锐钛矿和金红石相氧化钛组成；涂层致密层的硬度约为13．5GPa；在0．5N低载荷和摩擦循环次数小于2000次条件下，涂层同GCrl5钢对摩时的摩擦系数仅为0．18～0．20，较基底Ti6A14V与其对摩的摩擦系数低得多．摩擦过程中较软的GCr15钢球材料向涂层表面转移，涂层的磨损机制主要是轻微磨粒磨损与粘着磨损．     

微波烧结Al_2O_3陶瓷的研究

简要介绍了微波烧结的特点,对 Ａｌ２ Ｏ３ 陶瓷的微波烧结过程进行了介绍和分析,并同常规烧结进行了对比实验,在此基础上得出了一些结论,为陶瓷微波烧结提供了实验依据     

Effect of the stoichiometry on the electronic structure of the Ni（111）/α-Al2O3（0001） interface： a first-principles investigation

In this paper first-principles calculations of Ni（111）/α-Al2O3（0001） interfaces have been performed, and are compared with the preceding results of the Cu （111）/α-Al2O3（0001） interface [2004 Phil. Mag. Left. 84 425]. The AI- terminated and O-terminated interfaces have quite different adhesion mechanisms, which are similar to the Cu（111）/α Al2O3（0001） interface. For the O-terminated interface, the adhesion is caused by the strong O-2p/Ni-3d orbital hybridization and ionic interactions. On the other hand, the adhesion nature of the Al-terminated interface is the image-like electrostatic and Ni-Al hybridization interactions, the latter is substantial and cannot be neglected. Charge transfer occurs from Al2O3 to Ni, which is opposite to that in the O=terminated interface. The charge transfer direction for the Al-terminated and O-terminated Ni（111）/α-A1203（0001） interfaces is similar to that in the corresponding Cu（111）/α- Al2O3（0001） interface, but there exist the larger charge transfer quantity and consequent stronger adhesion nature, respectively.     

Li_4SiO_4陶瓷小球水解吸行为实验研究

采用程序升温热解吸(TPD/TDS)方法对Li4SiO4陶瓷小球的水解吸行为进行了实验研究。结果表明:水解吸过程中主要存在四个解吸峰;其中100℃附近的峰可解释为物理吸附水;150,250,400℃附近的峰可分别解释为以氢键、Li-OH和Si-OH配位键形式存在的化学吸附水。氚的释放与水的解吸几乎同步进行,且氚的释放形式主要为氚水(HTO),据此推测,氚水可能存在三种释放机制:(1)-OT+H2O→-OH+HTO;(2)-OH+-OH→H2O,-OT+H2O→-OH+HTO;(3)-OT+-OH→HTO。     

Investigation on the scattering effect of ceramic Nd:YAG

This paper investigates the scattering effect of domestic 0.5 at{\%} ceramic Nd:YAG. An effective method has been utilized to measure the scattering and absorption coefficients. An end-pumped continuous wave (CW) Nd:YAG ceramic laser was also demonstrated. A maximum output power of 6.7~W at 1064~nm was obtained at an 808-nm pump power of 32.9~W. Conversion efficiency and slope efficiency have been achieved. This indicates that scattering has an important effect on the optical performance of ceramic Nd:YAG.     

单层元胞结构金属泡沫的透射特性

本文构建了开孔泡沫铝的简化几何模型,并利用有限积分法模拟了具有单层元胞结构的金属泡沫材料在线性极化平面波垂直入射情况下的透射率。基于菲涅耳-基尔霍夫衍射理论分析了孔隙率、孔径尺寸、材料厚度和骨架结构对金属泡沫材料辐射特性的影响。当尺度参数较大时,金属泡沫材料的固相支架结构满足良导体条件,宏观电磁屏蔽效应显著,金属泡沫材料呈现"非透明"性质。随着入射电磁波波长逐渐接近于孔径尺寸,散射效应越来越显著,金属泡沫材料的"半透明"性质开始显现,不同孔隙率的金属泡沫材料的透射率以相近的规律随波长变化。随着波长的进一步减小,衍射效应对于金属泡沫材料透射特性的影响逐渐占据主导地位,采用菲涅耳-基尔霍夫衍射理论可以较好地描述透射能流在孔隙结构内的分布。当衍射效应占据主导地位时,对于相同孔隙率金属泡沫材料,孔径尺寸对衍射光学行为影响不大,而材料厚度、孔隙率和骨架结构会显著影响金属泡沫材料的透射率。     

爆电换能脉冲大电流输出研究

 基于爆电换能原理,使用掺铌的PZT 95/5陶瓷组装换能器件,在垂直工作模式下,对爆电电源LRC电路响应进行了理论分析,并开展了脉冲大电流输出实验研究。实验采用多组PZT 95/5铁电陶瓷并联,利用平面波发生器作为冲击加载手段,获得了峰值5 kA以上的脉冲大电流,初始电流上升速率可达10~20 GA/s。实验结果与理论设计符合较好。     

Highly transparent cerium doped gadolinium gallium aluminum garnet ceramic prepared with precursors fabricated by ultrasonic enhanced chemical co-precipitation

Cerium doped gadolinium gallium aluminum garnet (GGAG:Ce) ceramic precursors have been synthesized with an ultrasonic chemical co-precipitation method (UCC) and for comparison with a traditional chemical co-precipitation method (TCC). The effect of ultra-sonication on the morphology of powders and the transmittance of GGAG:Ce ceramics are studied. The results indicate that the UCC method can effectively improve the homogenization and sinterability of GGAG:Ce powders, which contribute to obtain high transparent GGAG ceramic with the highest transmittance of 81%.     

Preparation and performance of a novel polyimide foam

A new type of polyimide foam (PIF) was prepared and characterized based on a one‐pot process by the reaction of a first solution with different ratios of a second solution. The first solution was comprised of pyromellitic dianhydride (PMDA), N, N‐dimethyl formamide (DMF), methanol, water, surfactant, and catalysts, while the second solution contained polyaryl polymethylene isocyanate (PAPI). In the present study, the relationships among compositions, structures, and properties of PIFs were investigated. The results indicated that with the increase in the weight ratio of PAPI/(first solution), the foaming degrees of PIFs increased from 10.14 to 10.52 times and the apparent densities before postcure decreased from 15.96 to 14.51 kg/m³. The open cell contents, average sound absorption coefficients, and average cellular diameters of PIFs after postcure increased with increase in the weight ratio of PAPI/(first solution). The glass transition temperatures (T_g) of PIFs after postcure first increased from 287 to 299°C, then decreased to 292°C, and the 5% weight loss temperatures and 10% weight loss temperatures presented the same trend as well. The compressive and flatwise tensile properties scaled very well with the relative densities of the foams after postcure, with the highest compressive strength of 0.03 MPa and the highest flatwise tensile strength of 0.15 MPa. Copyright © 2011 John Wiley & Sons, Ltd.     

低温烧结NaBi(WO4)2陶瓷的介电性能

采用固相合成法制备了（WO₄）₂（NBW）陶瓷，研究了NBW陶瓷的相结构、形貌、烧结特性和微波介电性能。NBW陶瓷在625~800℃烧结1~4 h能够致密化。X射线衍射表明在625~800℃烧结2 h的NBW陶瓷均为四方晶系白钨矿结构的单相陶瓷。随着烧结温度的提高，NBW陶瓷的介电常数、品质因数（Qf值）先增加后降低，谐振频率温度系数逐渐降低。经650℃烧结2 h获得的NBW陶瓷的介电常数为14.36，Qf值为16 503 GHz，谐振频率温度系数为-1.055×10-5℃^-1。NBW陶瓷与银共烧反应生成Ag₂W₂O₇相，而与Au、Al共烧具备化学兼容性。