Cryoscopic and dynamic study of the molten system fluoroacetamide-sodium trifluoroacetate

The behavior of the molten system acetamide-electrolyte, including the peculiarity of the structure and the consequent relevant properties, such as the megavalue of the dielectric constant, was reported earlier. The probable structure is a micellar system composed of salt micelles dispersed in an amorphous solvent. The present paper reports measurements in a related system: fluoroacetamide-sodium trifluoroacetate. The phase diagram, the ultrasonic absorption of both longitudinal and shear waves, and the longitudinal relaxation time of the nuclear magnetic momentum were measured at different temperatures. The most importnat result was thatT ₁ (NMR relaxation time) on the¹⁹F nucleus shows that the amide and salt participate in different environments. The amide environment is less rigid; this proves that the system must be considered microheterogeneous. Moreover, the present system exhibited: 1) a less extended concentration area where supercooling phenomena occur; 2) a much broader curve of the real part of the mechanical impedance versus frequency; 3) a higher bulk viscosity in comparison with the CH₃CONH₂?CF₃COONa supercapacitive system.     

Improvements in Silo Design for Moist and Cohesive Bulk Solids by Using a Silo Centrifuge

The Jenike‐method is state of the art in silo design for trouble‐free flow, even for cohesive bulk solids. However, for some bulk solids, especially very cohesive and moist bulk solids, even the correct application of the Jenike‐method can lead to an over‐design of the silo outlet. If a reliable estimation of the critical outlet dimension is possible the dimension as well as the machinery costs can be reduced. Model testing can help to reduce the over‐design but reasonable test equipment and flexibility are only possible with silo centrifuge testing. Results, regarding the state of stress and the critical outlet dimensions, from experiments using a silo centrifuge with cohesive and moist bulk solids are presented. The influence of creeping effects on silo design is investigated using the silo centrifuge with moist gypsum.     

Thermal monitoring of morphology in triblock terpolymers with crystallizable blocks

The bulk morphology of poly(1,4‐butadiene)–block–polystyrene–block–poly (ethylene oxide) (PB‐b‐PS‐b‐PEO) and polyethylene–block–polystyrene–block–poly (ethylene oxide) (PE‐b‐PS‐b‐PEO) triblock terpolymers is analyzed under a thermal protocol. This allows the investigation of the morphology during the occurrence of thermal transitions, such as crystallization and melting, which is a neat way of studying the competition between microphase separation and crystallization for the morphology formation. Only one of the studied systems presented a morphological transition upon melting of the PEO and the PE blocks, attributed to the crystallization of the PE block in finite interconnected domains. All the other systems presented no morphological transitions during the thermal scan. The results prove that the crystallization only disrupt the microphases generated in the molten state under very specific circumstances for these block copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3197–3206, 2007     

The shuttle dispatch problem with compound Poisson arrivals: Controls at two terminals

We consider the control of an infinite capacity shuttle which transports passengers between two terminals. The passengers arrive at each terminal according to a compound Poisson process and the travel time from one terminal to the other is a random variable following an arbitrary distribution. The following control limit policy is considered: dispatch the shuttle at terminali, at the instant that the total number of passengers waiting at terminali reaches or exceeds a predetermined control limitm _i . The objective of this paper is to obtain the mean waiting time of an arbitrary passenger at each terminal for given control valuesm ₁ andm ₂. We also discuss a search procedure to obtain the optimal control values which minimize the total expected cost per unit time under a linear cost structure.     

Effect of high gamma dose on the PADC properties

The effect of the properties of PADC nuclear track detectors after exposure to high doses of gamma absorbed doses up to 5×10⁵ Gray (50 Mrad) were studied. The gamma source was a 9.03 PBq (244 KCi), Co-60 source. Results indicate that each of the bulk etch rate (V_b), the tracks etch rate (V_t) and the sensitivity (V) of the detectors increases with the high gamma absorbed dose, but there is a drop in these parameters at the low gamma absorbed dose. Signs of surface roughness were observed by increasing the gamma absorbed doses and changes in color observed for doses larger than 2×10⁵ Gray. The temperature of detectors during irradiation time reached 41°C. The fission fragment tracks (from Cf-252 source) disappeared quickly within the etching time (minutes) for total absorbed doses greater than 3×10⁵ Gray due to their high bulk etch rate.     

半导体中的自旋弛豫--从体材料到量子阱、量子线、量子点

本文对半导体中的自旋弛豫过程给出一个简要的回顾,介绍了半导体材料从体材料到量子阱、量子线、量子点不同维数的结构中各种自旋弛豫过程,主要关注了自旋去相位和相干控制。对于不同材料中的各种弛豫机制,关注的重点在于如何能够在实验上以一种可以控制的方式来改变可调参数从而达到控制自旋弛豫过程。这些参数主要有电场、磁场、温度、应变、有效g因子等等。本文的组织上,首先介绍研究前景,第1部分简要介绍了自旋弛豫的四种机制。第2部分按照维数的不同将半导体中自旋弛豫分为3个部分:体材料、量子阱、量子线、量子点,在每一部分中又基本上按照电子、空穴、激子的顺序进行了简要的总结:对于不同的载流子,考虑了自旋弛豫对可调参数的依赖关系。这些结果要么试图解释了已有的实验结果,要么从理论上给出预言从而给实验指明了方向,为室温下可以使用的自旋电子学器件设计提供了依据,为固态量子计算和量子信息处理铺平了道路。最后简单地给出展望。     

Characterization and study of microwave activation effects on the polystyrene tacticity

¹³C Nuclear magnetic resonance proved to be an advantageous tool to determine the stereoregularity of polystyrene polymers. The latter was achieved through the analysis of the signal of the quaternary carbon and that of the carbon-p in the aromatic ring too. Styrene was polymerized through microwaves and conventional heating activation using two different polymerization techniques: emulsion and bulk. Microwave activation was performed in a mono-modal type device under the following experimental conditions: various initiator concentrations, an average irradiation power of 50?W, temperature of 70°C, and using a batch reactor for emulsion and bulk experiments. The results obtained in these experiments were compared with those obtained by conventional heating activation polymerization under the same initiator concentration and temperature conditions. Microwave-activated reactions resulted in shorter reaction times and higher yields. The tacticity of the polymer samples was not significantly altered, which lead to the conclusion that, in this case, the stereoregularity of polystyrene was not influenced by microwave irradiation.     

Mechanical behaviour of the upper layers of a sandy loam soil under shear loading

The mechanical behaviour of the upper layers of a sandy loam soil was studied under standard triaxial compression and direct shear box tests. Variations of soil material properties were investigated at four different initial dry bulk densities of 1410, 1520, 1610 and 1670 kg/m³. Soil deformation and volume change under the triaxial compression loading were also studied at these bulk densities. Results from the two tests showed increases in the soil mechanical properties with the initial dry bulk density. The internal friction angle values measured with the triaxial compression apparatus exceeded those measured with the direct shear box. In contrast, the soil cohesion values measured with the direct shear box exceeded those measured with the triaxial compression apparatus. Under the triaxial compression test, the loose soil samples underwent contraction and volume reduction, whereas the dense samples swelled and failure cracks appeared clearly at various planes. The soil contraction for the former case characterizes the occurrence of soil compaction, whereas the cracks propagation and volume increase in the latter case characterizes the breaking up and loosening of soil during tillage operations. For the loose and moderately compacted states, the engineering Poisson's ratio increased with the axial strain until loading was completed. It also increased at the compacted and very compacted states until reaching given loading stages, after which its value started to decrease. This shifting in the engineering Poisson's ratio during loading may provide another identification of the moment of soil failure occurrence, in addition to that of the maximum shear stress.     

Modeling and prediction of bulk properties of open-cell carbon foam

The emerging ultralightweight material, carbon foam, was modeled with three-dimensional microstructures to develop a basic understanding in correlating microstructural configuration with bulk performance of open-cell foam materials. Because of the randomness and complexity of the microstructure of the carbon foam, representative cell ligaments were first characterized in detail at the microstructural level. The salient microstructural characteristics (or properties) were then correlated with the bulk properties through the present model. In order to implement the varying anisotropic nature of material properties in the foam ligaments, we made an attempt to use a finite element method to implement such variation along the ligaments as well as at a nodal point where the ligaments meet. The model was expected to provide a basis for establishing a process-property relationship and optimizing foam properties.The present model yielded a fairly reasonable prediction of the effective bulk properties of the foams. We observed that the effective elastic properties of the foams were dominated by the bending mode associated with shear deformation. The effective Young's modulus of the foam was strongly influenced by the ligament moduli, but was not influenced by the ligament Poisson's ratio. The effective Poisson's ratio of the foam was practically independent of the ligament Young's modulus, but dependent on the ligament Poisson's ratio. The effective Young's modulus of the carbon foam was dependent more on the transverse Young's modulus and the shear moduli of the foam ligaments, but less significantly on the ligament longitudinal Young's modulus. A parametric study indicated that the effective Young's modulus was significantly improved by increasing the solid modulus in the middle of the foam ligaments, but nearly invariant with that at the nodal point where the ligaments meet. Therefore, appropriate processing schemes toward improving the transverse and shear properties of the foam ligaments in the middle section of the ligaments rather than at the nodal points are highly desirable for enhancing the bulk moduli of the carbon foam.     

高效钙钛矿-有机本体异质结杂化串联太阳能电池

制备了一种有机铅卤钙钛矿-有机本体异质结杂化串联太阳能电池。采用紫外可见吸收光谱、原子力显微镜对薄膜形貌进行了表征。结果表明:有机本体异质结层可以有效改善钙钛矿的表面形貌, 增强了可见光的吸收。优化后的串联结构电池的短路电流可达19.14mA/cm², 开路电压为0.76V, 光电转换效率达到了6.54%。钙钛矿电池和有机本体异质结电池串联结构可以同时提高短路电流及填充因子, 二者具有较好的相容性和协同作用。