Viscoelastic properties and interfacial tension of polystyrene–polyethylene blends

The linear viscoelastic properties of polystyrene polyethylene (PS/PE) blends have been investigated in the molten state. For concentrations of the dispersed phase equal to 30 vol %, the blends exhibited a droplet‐matrix morphology with a volume‐average diameter of 5.5 μm for a 70/30 PS/PE blend at 200 °C and 14.7 μm for a 30/70 PS/PE blend at 230 °C. Enhanced elasticity (G′) for both blends, in the terminal zone, compared to the modulus of the matrix (PS and PE, respectively) was observed. This is related to the deformation of the droplets in the matrix phase and hence to the interfacial forces between the blend components. The results for these uncompatibilized blends are shown to be in agreement with the predictions of the emulsion model of Palierne. These predictions were used to obtain the interfacial tension between PS and PE, which was found to be between 2 and 5 mN/m at 200 °C and 4 ± 1 mN/m at 230 °C. Independent interfacial tension measurements using the breaking‐thread method resulted in a value of 4.7 mN/m and 4.1 mN/m at 200 °C and 230 °C for the respective blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1359–1368, 2000     

ASAXS study of styrene‐grafted sulfonated poly(vinylidene fluoride) membranes

Small‐angle and wide‐angle X‐ray scattering and anomalous small‐angle X‐ray scattering were used to investigate proton‐conducting membranes prepared by radiation‐induced styrene grafting and sulfonation of commercial poly(vinylidene fluoride) (PVDF‐g‐PS) films. The membranes retain the lamellar and highly oriented structure of the original PVDF films even through excessive grafting and sulfonation. The sulfonate groups aggregate in the central part of the amorphous layers, where they form a weakly ordered structure that does not show any preferred orientation. This structure is suggested to be lamellar with alternate metal‐sulfonated hydrate and PVDF‐g‐PS layers. The lamellar period is 15.1 Å. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1734–1748, 2000     

Interfacial tension and acid‐base approaches to polymer interactions

A significant correlation has been shown to exist between the interfacial tension of polymer pairs and their acid‐base pair interaction. The relationship is inverse, with interfacial tensions decreasing as acid‐base interactions increase. Interfacial tensions, frequently used as an indicator of polymer compatibility, were measured by the breaking thread method at temperatures in the vicinity of 200 °C. Acid‐base pair interaction values were measured by inverse gas chromatography over wide temperature ranges. The observed correlation confirms the important contribution made by short‐range, acid‐base interactions to the observed value of interfacial tension and supports the prediction of equations based on fundamental definitions of surface forces. A collateral finding of this work is the decrease of acid‐base functionality with rising temperature for all polymers studied. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2096–2104, 2000     

Toughening of a copolyester with a maleated core‐shell toughener

A reactive extrusion process was developed to toughen an amorphous copolyester (PETG) of ethylene glycol, terephthalic acid and 1,4‐cyclohexanedimethanol using either a maleic anhydride grafted polyethylene–octene elastomer (POEg), or a maleic anhydride grafted mixture (TPEg) of the polyethylene–octene elastomer and a semicrystalline polyolefin plastic as the impact modifier. TPEg showed an important toughening effect on the PETG. A sharp ductile‐brittle transition was observed when the TPEg content was about 10 wt %. For POEg toughened PETG, the ductile–brittle transition required a higher content in POEg, ∼15 wt %. Evolution of the topography and morphology of the blends and the relationship between impact strength and topography were discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2801–2809, 2000     

Processing and morphological development of carbon black filled conducting blends using a binary host of poly(styrene co‐acrylonitrile) and poly(styrene)

The effects of host/filler interactions, processing, and morphological development of low percolation threshold (Φ_c) conducting blends were investigated. It was found that the value of Φ_c was dramatically reduced by the isolation of the carbon black (CB) conducting filler at the cocontinuous interface of a binary poly(styrene) (PS) and poly(styrene co‐acrylonitrile) (SAN) insulating host, resulting in a multiple percolation effect. Accumulation of the filler at the interface was possible due to the incompatibility of the CB filler with the PS phase and partial compatibility with the SAN phase. The best results were obtained by initially dispersing the CB in the PS phase during melt‐ blending, followed by the addition of the SAN phase. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3106–3119, 2000     

Reactivity of functional SAN toward coreactive EPR‐g‐MA at planar interface

The grafting kinetics of reactive poly(styrene‐co‐acrylonitrile) (SAN) onto EPR‐g‐MA was studied under isothermal conditions, at the planar interface of an SAN/ethylene‐propylene rubber (EPR) bilayer film in relation to the type of reactive groups, NH₂ versus carbamate (which is an amine precursor), attached to SAN. The amount of SAN chemically bound to EPR chains at the interface was estimated by selectively washing off the unreacted SAN chains before X‐ray photon spectroscopic analysis of the released surface. It is clear that the mutual reactivity of the reactive groups, i.e., the NH₂–MA pair versus the carbamate–MA pair, has a decisive effect on the amount of SAN that reacts with EPR‐g‐MA at the interface. In case of SAN‐carb, the grafting reaction is controlled by the thermolysis of the carbamate groups into primary amines. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3682–3689, 2000     

Rheological behavior and prediction for blending conditions of a thermotropic liquid crystalline polyester with nylon

The dynamic rheological behavior of a liquid crystalline polymer (LCP), Vectra™ A, and nylons was investigated. The viscosities of nylon 66 and nylon 6 decrease slowly with an increase in temperature, while the viscosity of Vectra A drops dramatically at 280 °C, but remains slightly changed above 300 °C. At constant frequency and above 300 °C, the mean value of the activation energy of Vectra A is about 87.0 kJ/mole, but jumps to a much higher value of about 407.0 kJ/mole if the melt temperature is below 300 °C. The activation energy of Vectra A above 300 °C is lower than nylon 66, which shows that the viscosity of nylon 66 has a greater temperature dependence than Vectra A. The viscosity ratio of Vectra A to Nylon 66 is less than 1 at temperatures higher than 290 °C, which indicates that Vectra A can form the fibrils in the nylon 66 matrix and reinforce nylon 66 when blending them above this temperature. Experimental data confirm our prediction. Copyright © 2000 John Wiley & Sons, Ltd.     

Conductivity and structure of melt‐processed polyaniline binary and ternary blends

In the present study, conductive binary and ternary blends containing polyaniline (PANI) were developed through melt blending. The binary blends' investigation focused on the morphology, in light of the components' interaction, and the resulting electrical conductivity. Similar solubility parameters of a given doped PANI and a matrix polymer lead to dispersion of fine PANI particles within the matrix, and to formation of conducting paths at low PANI contents. A plasticizer acting also as a compatibilizer improves the matrix polymer/PANI interactions. In ternary blends consisting of PANI and two immiscible polymers, the PANI preferrentially locates in one of the components, affecting the blend's morphology. This “concentrating” effect leads to relatively high electrical conductivity at a low PANI content. The electrical conductivity of the studied ternary blends is almost independent of the components' sequence of addition into the hot melt mixing device, exhibiting the selectivity of PANI towards one of the components. Copyright © 2000 John Wiley & Sons, Ltd.     

Packed Column SFC of Gas Oils. Part II: Experimental Design Optimization of the Group-Type Analysis using CO2-SF6 as the Mobile Phase

An optimization procedure is presented for group-type analysis of diesel fuel by supercritical fluid chromatography using packed silica column and a mixed mobile phase. A set of five responses, four values of resolution of a performance mixture and analysis time, was modeled using a Doehlert matrix for experimental design. Optimized experimental conditions for the five responses were obtained from a response surfaces optimization, taking into account various constraints on SF₆ content in mobile phase and analysis time. The predicted and experimental resolutions were in good agreement for the different optimized conditions and one of them was selected to for application to a given diesel fuel for comparison with the results obtained by SFC using pure CO₂ and by HPLC. The conditions found in this study provide an alternative method for the determination of mono-, di-, and polyaromatic compounds in middle distillates.