薄层色谱-紫外可见分光光度法测定食品中的苏丹红Ⅰ号

建立了测定食品中苏丹红Ⅰ号新方法:薄层色谱-紫外可见分光光度法.方法的线性回归方程为:A=0.00583 0.15105ρ,在0.50～10.0 μg/mL之间苏丹红Ⅰ号的浓度与吸光度之间呈线性关系,相关系数R=0.9992,检出限为0.05 μg/mL.测定结果与国家标准HPLC法对照,令人满意.可用于食品中苏丹红Ⅰ号的测定.     

Dielectric Properties Investigation of Metal–Insulator–Metal (MIM) Capacitors

This study presents the construction and dielectric properties investigation of atomic-layer-deposition Al₂O₃/TiO₂/HfO₂ dielectric-film-based metal–insulator–metal (MIM) capacitors. The influence of the dielectric layer material and thickness on the performance of MIM capacitors are also systematically investigated. The morphology and surface roughness of dielectric films for different materials and thicknesses are analyzed via atomic force microscopy (AFM). Among them, the 25 nm Al₂O₃-based dielectric capacitor exhibits superior comprehensive electrical performance, including a high capacitance density of 7.89 fF·µm⁻², desirable breakdown voltage and leakage current of about 12 V and 1.4 × 10⁻¹⁰ A·cm⁻², and quadratic voltage coefficient of 303.6 ppm·V⁻². Simultaneously, the fabricated capacitor indicates desirable stability in terms of frequency and bias voltage (at 1 MHz), with the corresponding slight capacitance density variation of about 0.52 fF·µm⁻² and 0.25 fF·µm⁻². Furthermore, the mechanism of the variation in capacitance density and leakage current might be attributed to the Poole–Frenkel emission and charge-trapping effect of the high-k materials. All these results indicate potential applications in integrated passive devices.     

缓冲层ZnPc对有机电致发光器件特性的影响

本文研究了酞菁锌(ZnPc)薄膜的表面形貌及ZnPc薄膜作为缓冲层对有机电致发光器件(OLEDs)光电特性的影响.对比两组样品的AFM图像,ZnPc薄膜相比于ITO薄膜,其表面的岛面积较大,薄膜表面更连续平整,基本上覆盖了ITO膜表面针孔,减少了表面的缺陷.另外,ZnPc薄膜的岛分布均匀有序.使用ZnPc作为缓冲层的器件性能明显好于未使用ZnPc修饰的器件,在7.42V的驱动电压下的最大发光亮度达到1.428kcd/m2,在4.3V电压驱动下时,最大光功率效率为1.411m/W;而未使用缓冲层的器件在8V的驱动电压下达到最大发光亮度达到1.212kcd/m2,在5.5V电压驱动下时,最大光功率效率为0.931m/W.     

用化学溶液方法在Ni-5at%W基底上制备La2Zr2O7过渡层的研究

La2Zr2O7(LZO)过渡层以其独特的物理化学性质越来越受到人们的关注。本文以乙酰丙酮镧和乙酰丙酮锆为前驱盐,丙酸为溶剂配置前驱液,用化学溶液方法(CSD)在具有立方织构的Ni-5at%W基底上制备了LZO过渡层薄膜。研究了前驱液成分、性质以及退火温度对LZO成相以及取向的影响。用常规XRD和X射线四环衍射仪分析了LZO薄膜的相成分和织构。结果显示,在1050℃下退火可以获得强立方织构的LZO薄膜,其中(222)峰的Phi扫描半高宽值为8.95°;(400)峰的Chi扫描半高宽值为6.8°。用高分辨扫描电子显微镜(FE-SEM)观察到LZO薄膜表面均匀致密,没有裂纹和空洞。     

发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

ZnO-Si不同退火条件对生长ZnSe薄膜的影响

研究了作为缓冲层的ZnO薄膜在不同的退火时间、退火温度下退火对Si衬底上生长ZnSe膜质量的影响。当溅射有ZnO膜的Si(111)衬底的退火条件变化时，从X射线衍射谱（XRD）和光致发光谱（PL）中可见，ZnSe(111)膜的晶体质量有较大的变化。变温的PL谱表明，Si衬底上生长的具有ZnO缓冲层的ZnSe膜的近带边发射峰起源于自由激子发射。     

HL-1装置脱离等离子体及边界等离子体杂质辐射的观测

首次用三道光纤探测器,伸入HL-1装置内真空室,采集活动石墨孔栏处等离子体光信号,用22m石英长光纤传输光信号至控制室进行观测。通过边界等离子体H_α和杂质辐射的时空分布,初步探讨了HL-1装置的脱离等离子体。     

Analysis of the generation mechanism of the S-shaped J—V curves of MoS2/Si-based solar cells

Amorphous-microcrystalline MoS$_{2}$ thin films are fabricated using the sol-gel method to produce MoS$_{2}$/Si-based solar cells. The generation mechanisms of the S-shaped current density-voltage ($J$-$V$) curves of the solar cells are analyzed. To improve the performance of the solar cells and address the problem of the S-shaped $J$-$V$ curve, a MoS$_{2}$ film and a p$^+$ layer are introduced into the front and back interfaces of the solar cell, respectively, which leads to the formation of a p-n junction between the p-Si and the MoS$_{2}$ film as well as ohmic contacts between the MoS$_{2}$ film and the ITO, improving the S-shaped $J$-$V$ curve. As a result of the high doping characteristics and the high work function of the p$^+$ layer, a high-low junction is formed between the p$^+$ and p layers along with ohmic contacts between the p$^+$ layer and the Ag electrode. Consequently, the S-shaped $J$-$V$ curve is eliminated, and a significantly higher current density is achieved at a high voltage. The device exhibits ideal p-n junction rectification characteristics and achieves a high power-conversion efficiency (CE) of 7.55%. The findings of this study may improve the application of MoS$_{2}$ thin films in silicon-based solar cells, which are expected to be widely used in various silicon-based electronic and optical devices.     

Polycrystalline silicon films prepared by metal-induced crystallisation using pre- and post-deposited aluminium on amorphous silicon

We report on the successful fabrication of polycrystalline silicon films by aluminium-induced crystallisation (AIC) of Radio frequency (rf) plasma-enhanced chemical vapour deposited (PECVD) a-Si films. The effects of annealing at different temperatures (300 and 400°C), below the eutectic temperature of the Si–Al binary system, on the crystallisation process have been studied. This work emphasises the important role of the position of the Al layer with respect to the Si layer on the crystallisation process. The properties of the crystallised films were characterised using X-ray diffraction, Raman spectroscopy, ellipsometry, field-emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). With an increase in the annealing temperature, it was found that the degree of crystallisation of annealed a-Si/Al and Al/a-Si films increased. The results showed that the arrangement where the Al was on top of the a-Si had a more prominent effect on crystallisation enhancement than when Al was below the a-Si. The interfacial layer between the Al and a-Si film is crucial because it influences the layer-exchange process during annealing. The oxide layer formed between the Al and the a-Si layers greatly retards the crystallisation process in the case of the Al/Si arrangement. Our investigations suggest that polycrystalline Si films formed by AIC can be used as a seed layer in solar cell fabrication.     

Newton trajectories for the tilted Frenkel–Kontorova model

ABSTRACT

Newton trajectories are used for the Frenkel–Kontorova model of a finite chain with free-end boundary conditions. We optimise stationary structures, as well as barrier breakdown points for a critical tilting force were depinning of the chain happens. These special points can be obtained straight forwardly by the tool of Newton trajectories. We explain the theory and add examples for a finite-length chain of a fixed number of 2,?3,?4,?5 and 23 particles.