A new microtensile tester for the study of MEMS materials with the aid of atomic force microscopy

An apparatus has been designed and implemented to measure the elastic tensile properties (Young's modulus and tensile strength) of surface micromachined polysilicon specimens. The tensile specimens are “dog-bone” shaped ending in a large “paddle” for convenient electrostatic or, in the improved apparatus, ultraviolet (UV) light curable adhesive gripping deposited with electrostatically controlled manipulation. The typical test section of the specimens is 400 μm long with 2 μm×50 μm cross section. The new device supports a nanomechanics method developed in our laboratory to acquire surface topologies of deforming specimens by means of Atomic Force Microscopy (AFM) to determine (fields of) strains via Digital Image Correlation (DIC). With this tool, high strength or non-linearly behaving materials can be tested under different environmental conditions by measuring the strains directly on the surface of the film with nanometer resolution.     

书籍扫描图像畸变参数自动计算方法的研究

为实现书籍扫描图像的畸变自动校正,提出用多项式来描述各像素的理论灰度g(zi)与页面上对应点到扫描仪工作平面距离zi二者之间的关系。为确立该多项式,在畸变参数已知条件下扫描一幅图像,根据已知畸变参数求出zi,即可按最小二乘法原理由各像素灰度的实际值求出多项式的各个系数。实验证明,采用4阶多项式已能满足一般要求,并求出了各系数。对任意扫描图像,自动计算畸变参数的方法为:首先利用扫描图像上页边空白处各像素的灰度,对畸变参数进行估计,并求出zi的估计值;然后代入所确立的多项式,可求得g(zi);通过调整各畸变参数的估计值,直到g(zi)与gi最为接近,即得最佳畸变参数。用于图像校正实验,获得了较好的校正效果,最大误差由不校正时的41%下降到了6.9%。这使得无需用户测量并输入有关畸变参数即可进行自动校正。     

Tests of ordered hypotheses in linkage in heredity

The asymptotic null distribution of the likelihood ratio test for two cases of ordered hypotheses in a particular genetic model is considered. A simple iterative process is proposed in order to get the restricted estimates. It is shown that both tests have asymptotically a chi-bar squared distribution and the same size. A simulation study is also conducted in order to compare the usual unrestricted test with the corresponding one of ordered hypotheses. Finally, the results are extended to some special cases.     

宁波港船舶交通管理系统(VTS)

通过对宁波港的交通环境，现有VTS系统及港口发展的趋势研究，提出了改善宁波港通航环境，建立和完善VTS系统的有效措施。     

利用计算机辅助装调检测矩形大口径离轴非球面的方法研究

通过非球面的零位补偿法,完成了对矩形大口径离轴非球面镜的检测。先用光学设计软件Zemax从理论上分析了在检测中会出现的现象,并结合计算机辅助装调技术,确定在检测过程中相对敏感的自由度,然后控制这些量,使补偿器和非球面的相对关系与理论设计相吻合,在Zygo相位干涉仪上测得最终结果。在λ=632.8nm时,中心圆口径与两个边缘圆口径面形误差RMS分别为0.022λ,0.037λ,0.032λ。检测结果,达到预期目的。     

Development of a Millimeter Wave Compact Equipment for NDT of Materials

We developed a compact equipment working at 94 GHz to replace the commonly used network analyzer for nondestructive testing of materials. The compact equipment was designed to measure the variations in the amplitude and phase of the reflected signal from the material relative to a reference signal. A good accuracy of the amplitude and phase measurement of the equipment was obtained in the confirmative experiments. The distribution of a drop of water in a wood plate is clearly visible in the millimeter wave images obtained by the amplitude and phase measurement.     

基于分层光学扫描的三维数字化测量技术

采用切削分层光扫描测量与计算机数据信息合成相结合的方法，有效地解决了具有复杂内外腔结构零件的三维数字化测量。该方法比传统三维测量速度快、自动化程度高，能同时准确测量零件内外腔表面，零件边缘测量误差可控制在CCD两个像素内。利用获取的铝合金精密小箱体三维数据，在计算机上重构了零件的三维模型，并用RP技术制造出了零件物理原形。     

旧式大型工具显微镜数显化

大型工具显微镜是用途较广的精密长度计量仪器,主要用于测量螺纹中径、圆柱的直径等。目前实验室和工厂现有的仪器属50年代生产的老型号产品,用目视螺旋测微鼓上的刻度读数,人工记录和处理数据,测量时费时费工。针对大型工具显微镜数显化的问题,阐述了光栅、光电显微镜、单片机、新型传感器在数显上的应用。利用新技术和新型传感器改造老设备,使其实现数字化和智能化,以提高测量效率和测量精度。改造的结果表明,改造后的仪器测量效率大大提高,精度可提高一个数量级。     

偏振小孔干涉仪

偏振小孔干涉仪是一种可实用的新型干涉仪。它综合小孔衍射技术、偏振技术和共光路设计为一体,具有条纹对比度可调、抗干扰能力强和非接触检验等优点,可广泛用于各种光学元件及其胶合层的检验。目测精度达1/10λ,计算机条纹处理精度可调。     

浅议物理实验教学环节改革

为进一步提高大学物理实验的教学质量，本文就实验课的预习、操作、实验报告的撰写及考核方法进行了探讨。