Effect of grinding on thermal reactivity of ceramic clay minerals

The effect of grinding on thermal behavior of pyrophyllite and talc as commonly used ceramic clay minerals was investigated by DTA, TG, emanation thermal analysis (ETA), B.E.T. surface area (s.a.) measurements, X-ray diffraction (XRD) and scanning electron microscopy (SEM). A vibratory mill was used in this study, grinding time was 5 min. It was found that the grinding caused an increase in surface area and a grain size reduction of the samples. From TG and DTA results it followed that grinding caused a decrease of the temperature at which the structure bound OH groups released. The formation of high temperature phases was enhanced with the ground samples. For the ground talc sample the crystallization of non-crystalline phase into orthorhombic enstatite was observed in the range of 800°C. For ground pyrophyllite a certain agglomeration of grains was observed in the range above 950°C. Moreover, for both clays the ETA characterized a closing up of subsurface irregularities caused by grinding as a decrease of the emanation rate in the range 250–400°C. The comparison of thermal analysis results with the results of other methods made it possible to better understand the effect of grinding on the ceramic clays.     

Hepatobiliary excretion and brain distribution of caffeine in rats using microdialysis

To investigate the pharmacokinetic mechanism of hepatobiliary excretion and brain distribution of caffeine, this study uses a method based on microdialysis technique and liquid chromatography that allows continuous and concurrent in vivo monitoring of extracellular caffeine in the blood, brain and bile of anesthetized rats following the administration of caffeine (3 or 10 mg/kg, i.v.) through the femoral vein. Dialysates of the blood, brain and bile were directly injected onto the liquid chromatographic system and no further clean-up procedures were required. The study design consisted of two groups of six rats in parallel: the rats of the control group received caffeine (3 or 10 mg/kg, i.v.) alone and those of the cyclosporine treated-group were injected cyclosporine (10 mg/kg, i.v.) 10 min prior to caffeine administration (3 or 10 mg/kg, i.v.). The decline of caffeine in the blood, brain striatum and bile suggested that caffeine had rapid exchange and equilibration between the peripheral compartment and the central nervous system. In addition, the results indicated that caffeine underwent hepatobiliary excretion and was distributed into brain. When cyclosporine was co-administered, the pharmacokinetic parameters were not significantly altered. The results of this study reveal that the pharmacokinetic mechanism of hepatobiliary excretion and brain distribution of caffeine might not relate to P-glycoprotein.     

Solvation of amino acid residues in water and urea-water mixtures: Volumes and heat capacities of 20 amino acids in water and in 8 molar urea at 25°C

The limiting partial molar volumes V ^o and heat capacities C _p ^o of 20 amino acids have been determined in water and in 8 molar urea at 25.0°C using flow calorimetry and flow densimetry. The side chain contributions to V ^o and C _p ^o were obtained as the difference between the properties of the various amino acids and those of glycine, both in water and in 8M urea. The solvent accessible surface area of the amino acid residues were obtained using a method developed by Hermann, and the total surface areas were separated into their hydrophobic A _Hb and hydrophilic components. In water, C _p ^o values for the various residues C _p ^o (R) were found well correlated with A _Hb , though much less so in the urea solution. Hence, C _p ^o (R) values, in water yield a good estimate of side chain hydrophobicity, but the (waterurea) transfer heat capacities appear strongly affected by specific solvation effects in the urea solution.Presented at the sixth Italian meeting on Calorimetry and Thermal Analysis (AICAT) held in Naples, December 4–7, 1984.     

Optimization of the electrophoretic deposition of YBa2Cu3O7−x superconducting large area coatings

Large area coatings (>10cm²) of the high temperature superconductor YBa₂Cu₃O_7–x (x = 0.1 – 0.2) (YBCO) have been prepared by scale up an electrophoretic deposition technique using silver sheets and Si-wafers coated with Ag or Au as substrates. Several parameters, like the kind of the solvent, the applied voltage, the distance between the electrodes, the initial concentration of the suspension and the temperature during the electrophoresis were investigated in order to attain high deposition rates, as well as uniform YBCO coatings with the proper stoichiometry. To obtain a strongly adherent and dense coating a subsequent appropriate sintering and annealing procedure has been developed. The coatings obtained were characterized for their stoichiometry and superconducting properties by X-ray diffraction (XRD), Raman spectroscopy and magnetic measurements. The homogeneity and thickness of the films and the average grain size of the deposited particles have been investigated by optical and scanning electron microscopy (SEM).     

煤焦在燃烧过程中孔隙结构变化的模拟

煤焦在燃烧过程中的物理特性，如比表面积和孔径分布会发生连续变化，直接测量煤焦在燃烧过程中的孔隙结构变化很困难，但可以通过合适的数学模型来观察，二维的圆柱孔模型已大量用来对煤焦气化与燃烧过程中表面积和孔隙结构的变化进行模拟，这个模型把孔隙分成两大部分－－大孔与小孔，因为小孔构成比表面的绝大部分，所以在反应过程中比表面积的变化可以由单一小孔模型来拟合，本文采用了用Ｔｓｅｎｇ和Ｅｄｇａｒ提出的孔模型对几     

高比表面积介孔网状氧化镁的制备、表征及对废水中Pb(Ⅱ)的吸附性能和机理

以天然水菱镁矿为原料，通过"煅烧-水化-煅烧"的简单方法制备了高比表面积介孔网状MgO，且实验过程中无须加入任何试剂。系统性研究了氧化镁用量、吸附时间、吸附温度及pH对氧化镁吸附模拟废水中铅离子吸附性能的影响，揭示了吸附机理，并考察了氧化镁对多种离子的吸附效果。结果表明：该氧化镁吸附剂具有188 m²·g^-1的高比表面积和0.85 cm³·g^-1的高孔体积，平均孔径为12.33 nm，其吸附动力学和等温线数据与伪二级模型和Langmuir模型高度吻合，表明重金属离子在氧化镁上为单层化学吸附。MgO介孔网状结构表现出对Pb（Ⅱ）的高吸附性能，最大吸附量为7 431.5 mg·g^-1，该数值远高于其他报道的基于MgO吸附剂的数值，铅去除率高达99.8%以上。介孔网状MgO的吸附机理主要是羟基官能团以及Mg（Ⅱ）与MgO表面重金属离子之间的离子交换所致。另外，该氧化镁可同时吸附多种离子，对Cd、Cr、Ni、As、Co、P、Se、Be、Bi、Cu、Fe、Mn、V、Zn、Al离子均具有优异的吸附性能。     

Surface area of papermaking woodpulps used by the British paper industry

The surface area was determined for various papermaking woodpulps: bleached eucalyptus globulus sulphate pulp; bleached eucalyptus grandis sulphate pulp; bleached betula verrucosa sulphate pulp; bleached pine/spruce sulphate pulp; bleached pine/spruce sulphate pulp fines. The method of negative adsorption was used which gives an effective wet surface area. By looking at negative adsorption data more closely, some inference can be made about the morphology of the substrate.Glossary of symbols B (e²/2kT)^1/2 - ¯C concentration of fibre per unit volume of pulp - 1 - ¯¯c - h angle between pore and the axis of the bed in a permeable material - K permeability coefficient - k Boltzmann constant - k ₀ shape factor for pores in a permeable material - n _i concentration of co-ion in the bulk solution - n _i experimentally observed increase in concentration of co-ion in the bulk solution - S surface area - S _t wS - S ₀ surface area per unit volume of permeable material - V _t total volume of solution - V excluded volume - V _s excluded volume accessible to water but not to ions - V _obs experimentally observed excluded volume - w weight of dry fibre - ¯ effective volume of fibres in a permeable pad - surface potential at outer Helmholtz plane     

Efficient synthesis of magnetic nanoparticle-Musa acuminata peel composite for the adsorption of anionic dye

The impregnation of magnetite (Mt) nanoparticle (NPs) onto Musa acuminata peel (MApe), to form a novel magnetic combo (MApe-Mt) for the adsorption of anionic bromophenol blue (BPB) was studied. The SEM, EDX, BET, XRD, FTIR and TGA were used to characterize the adsorbents. The FTIR showed that the OH and CO groups were the major sites for BPB uptake onto the adsorbent materials. The average Mt crystalline size on MApe-Mt was 21.13 nm. SEM analysis revealed that Mt NPs were agglomerated on the surface of the MApe biosorbent, with an average Mt diameter of 25.97 nm. After Mt impregnation, a decrease in BET surface area (14.89 to 3.80 m²/g) and an increase in pore diameter (2.25–3.11 nm), pore volume (0.0052–0.01418 cm³/g) and pH point of zero charge (6.4–7.2) was obtained. The presence of Pb(II) ions in solution significantly decreased the uptake of BPB onto both MApe (66.1–43.8%) and MApe-Mt (80.3–59.1%), compared to other competing ions (Zn(II), Cd(II), Ni(II)) in the solution. Isotherm modeling showed that the Freundlich model best fitted the adsorption data (R² > 0.994 and SSE < 0.0013). In addition, maximum monolayer uptake was enhanced from 6.04 to 8.12 mg/g after Mt impregnation. Kinetics were well described by the pseudo-first order and liquid film diffusion models. Thermodynamics revealed a physical, endothermic adsorption of BPB onto the adsorbents, with ΔH^o values of 15.87–16.49 kJ/mol, corroborated by high desorption (over 90%) of BPB from the loaded materials. The viability of the prepared adsorbents was also revealed in its reusability for BPB uptake.     

神光-Ⅱ装置三倍频实验中靶场单元技术的改进

 主要介绍为了满足神光-Ⅱ高功率激光装置三倍频光（351nm，3ω）的物理实验要求，靶场三倍频模拟光源和瞄准监视系统两个主要单元技术的改进，即三倍频模拟光源由基频光（1 053nm，3ω）通过腔外的KTP+BBO晶体倍频获得，再经八路分光系统和主激光耦合；瞄准监视系统由透射式光学系统改进为反射式光学系统，避免原系统存在较大的色差，提高瞄准精度。     

Effect of bovine serum albumin on the surface properties of ionic liquid-type Gemini surfactant

The effect of bovine serum albumin on the surface properties of IL-type gemini surfactant ([C₁₀-4-C₁₀im]Br₂), have been investigated by surface tension method. The critical micelle concentration (CMC) as a function of BSA concentrations at various temperatures was investigated. The CMC of [C₁₀-4-C₁₀im]Br₂ increases with increasing the concentration of BSA as well as the temperature of the system. The interfacial parameters viz; maximum surface excess concentration (Γ_max), the minimum area per molecule (A_min), and surface pressure at CMC (Π_cmc) were calculated. In addition, thermodynamic parameters of adsorption and micellization were evaluated by using surface tension data. The results indicated that the binding of [C₁₀-4-C₁₀im]Br₂ to BSA is spontaneous and exothermic in nature. The process is entropy driven and hydrophobic interactions are the major driving forces.