A combined approach of Kullback–Leibler divergence and background subtraction for moving object detection in thermal video

In this work, a robust method for moving object detection in thermal video frames has been proposed by including Kullback–Leibler divergence (KLD) based threshold and background subtraction (BGS) technique. A trimmed-mean based background model has been developed that is capable enough to reduce noise or dynamic component of the background. This work assumed that each pixel has normally distributed. The KLD has computed between background pixel and a current pixel with the help of Gaussian mixture model. The proposed threshold is useful enough to classify the state of each pixel. The post-processing step uses morphological tool for edge linking, and then the flood-fill algorithm has applied for hole-filling, and finally the silhouette of targeted object has generated. The proposed methods run faster and have validated over various real-time based problematic thermal video sequences. In the experimental results, the average value of F₁-score, area under the curve, the percentage of correct classification, Matthew’s correlation coefficient show higher values whereas total error and percentage of the wrong classification show minimum values. Moreover, the proposed-1 method achieved higher accuracy and execution speed with minimum false alarm rate that has been compared with proposed-2 as well as considered peer methods in the real-time thermal video.     

Time reversal acoustic communication receivers: DSP implementation and fast channel estimation

A communication system is implemented on digital signal processors (DSPs) for the underwater acoustic environment. The implemented receiver uses time reversal multi-channel combining followed by a single-channel decision feedback equalizer. Periodic channel estimation is employed to track the channel fluctuations. These techniques are used to mitigate time-varying inter-symbol interference, which is the main challenge in the underwater acoustic channel at operating frequencies greater than 10 kHz. Various optimization tasks are performed to reduce the receiver computational complexity. A fast implementation of the matching pursuit algorithm is tested on the DSP platform. Its performance, in terms of accuracy and run-time, is compared with that of the basic matching pursuit algorithm. Experimental results of the transmission and demodulation of binary phase-shift keying signals at three different symbol rates were obtained in the local Delaware Bay. The low bit error rates demonstrate the effectiveness of our implementation.     

Object and Mathematical Simulation of Ammonium Hexafluorosilicate Sublimation

An integration of different modelling methods including object and mathematical simulation are suggested for sublimation processes of inorganic fluorides to optimally simulate the real technological conditions. The paper presents the results of testing this methodology on ammonium hexafluorosilicate sublimation.     

Constructing the Co cyclic Structures for Crossed Copro duct Coalgebras

In this paper, we construct a cocylindrical object associated to two coal-gebras and a cotwisted map. It is shown that there exists an isomorphism between the cocyclic object of the crossed coproduct c...     

水声通信中基于信道辨识的盲turbo均衡方法

水声信道多途效应明显,造成接收信号存在严重的码间干扰(ISI,Intersymbol interference)。基于最小均方误差(MMSE,Minimum mean square error)准则的turbo均衡器级联了均衡和信道译码,能够有效去除ISI,并获得优良的性能。由于水声信道的时变性,传统MMSE-turbo均衡需要周期性的训练序列,以实现连续可靠的通信。训练序列虽然提高了通信的可靠性,但降低了信息的有效传输速率。因此,为提高通信效率,本文提出了一种盲turbo均衡方法,该方法通过引入新的盲信道辨识器来同时获得信道估计响应和已去除部分ISI的初步均衡输出信号,并为turbo均衡提供初始的响应参数和比特软信息。与水声通信中应用较多的盲判决反馈均衡器(DFE,Decision feedback equalizer)相比,海上实验结果证明本文提出的盲turbo均衡方法抗信道多途衰落的能力较强,并且与传统MMSE-turbo均衡相比无需训练序列,因此提高了信息的有效传输速率。     

水下超疏油聚(3,4-乙烯基二氧)噻吩薄膜的制备简

以离子液体溴化(1-己基-3-甲基咪唑盐)作为电解质和掺杂剂采用电化学一步法制备了微纳米复合结构的聚(3,4-乙烯基二氧噻吩)薄膜,薄膜由槽内排布着纳米珠链的棒状结构组成. 研究表明,通过控制电流密度的大小,可以调节棒状结构和珠状结构的平均直径. 离子液体中的咪唑阳离子和对阴离子均掺杂到聚合物中,该薄膜具有可逆的电化学活性及水下超疏油特性.     

聚焦形貌恢复方法模型设计

采用基于拉普拉斯算符聚焦形貌恢复方法,提出了模拟目标深度测量的数值模型。数值模拟的核心是基于通过几何光学预测的理想图像的卷积与透镜广义孔径函数的多色点扩散函数,即用聚焦误差替代抛物线圆柱形貌或高斯函数。该模型可以使用基于聚焦形貌恢复方法的传感器真实组件参数、光源光谱、光学系统离差、相机的光谱灵敏度。提出了光学系统离差（消球差、消色差、色差）对确定目标表面形貌的精确度和可靠性的影响。结果表明,该模型可以有效提高实验效率,缩短时滞,降低成本。     

基于偏振特性对石英玻璃和绿漆涂层的反演

物质的偏振特性与其复折射率、表面粗糙度以及观测几何条件有关,为了应用偏振探测技术实现对目标的定量反演,本文首先对两种典型目标(绿漆涂层和石英玻璃)的偏振特性进行了实验测定,并对偏振度与探测天顶角的关系进行了分析。利用实验数据并基于描述目标偏振特性的PG模型首次在考虑了粗糙度的影响下,对目标的折射率、消光系数进行了定量反演,最后将反演结果与参考结果进行比较。结果表明,石英玻璃的折射率相对误差为4.944 9%,绿漆涂层的折射率与消光系数的相对误差分别为11%和21.558 9%。该方法在考虑表面粗糙度的条件下能够更精确地测定物质的复折射率,同时也为偏振技术应用于目标定量反演提供了依据。     

基于6S模型的遥感影像逐像元大气纠正算法

大气纠正的目的是从遥感影像中去除大气影响,并反演获取地物真实反射率。介绍了一种逐像元对遥感影像进行大气纠正的算法,该算法基于6S(Second Simulation of the Satellite Signal in the Solar Spectrum)大气辐射传输模型计算建立的查找表(look-up table),并利用地面暗目标(dark object)进行陆地气溶胶光学厚度的自动反演,由于气溶胶的分布具有空间连续性,在获取地面暗目标气溶胶光学厚度值后,通过空间插值的方法计算影像中非暗目标像元的气溶胶光学厚度值,经过查找表二次插值计算,逐像元进行大气纠正并获取像元地表反射率值。以Landsat5遥感影像为例,介绍了算法流程,展示了大气纠正的结果。结果显示,利用查找表逐像元大气纠正的算法,能够在一定程度上去除云雾对影像的影响,更加精确的对遥感影像进行大气纠正并获取地物的真实反射率。     

货车枕簧丢失故障动态图像识别方法

针对货车运行故障动态图像检测,提出无故障目标识别工作模式,解决货车枕簧丢失故障的自动识别问题。利用Haar特征提取枕簧特征信息,基于AdaBoost算法选取特征并构建层叠分类器,等比缩放搜索窗口检测货车图像,最终分选出无故障的枕簧图像,从而大大地减少了待识别图像的数量,显著地提高了人工识别效率。实验表明,该算法使用的特征简单,搜索策略高效,不受枕簧位置、缩放和旋转的影响,抗噪能力强,对分辨率低、局部遮挡、光照不足或过度曝光等质量较差的图像仍具有很强的适应性,所提出的方案能够满足全天候条件下的货车枕簧目标识别,为货车故障动态图像检测的工程化应用奠定了基础。