基于超声波测量技术的颗粒尺寸分布模型的研究

提出了一种利用单颗粒背向散射信号来进行粒径分布估算的超声波测量技术,系统阐述了其 理论基础及基本工作原理。被测颗粒的散射信号幅度与它在探测区中的位置、颗粒尺寸和形状有关。 通过理论分析,建立了一个可用于描述散射信号幅度概率分布与颗粒系尺寸分布之间关系的数学模 型,对该模型的反演计算便可得到颗粒系的尺寸分布信息。为了避免求解过程中的病态系数矩阵问 题,将模型求解转化成了易于解决的最优化问题。仿真实例结果验证了该技术的可行性。     

加拿大一枝黄花总酚超声提取工艺

利用超声提取的方法,通过单因素和正交实验分析了溶液浓度、超声时间、料液比、提取次数4个主要因素对总酚提取率的影响。确立了加拿大一枝黄花总酚的最佳提取工艺条件为:60%甲醇、超声50min、料液比1∶20、提取3次。在此条件下,总酚的提取率为44.61mg/g。     

Controlled Space Radiation concept for mesh-free semi-analytical technique to model wave fields in complex geometries

Numerical modelling of the ultrasonic wave propagation is important for Structural Heath Monitoring and System Prognosis problems. In order to develop intelligent and adaptive structures with embedded damage detector and classifier mechanisms, detailed understanding of scattered wave fields due to anomaly in the structure is inevitably required. A detailed understanding of the problem demands a good modelling of the wave propagation in the problem geometry in virtual form. Therefore, efficient analytical, semi-analytical or numerical modelling techniques are required. In recent years a semi-analytical mesh-free technique called Distributed Point Source Method (DPSM) is being used for modelling various ultrasonic, electrostatic and electromagnetic wave field problems. In the conventional DPSM approach point sources are placed along the transducer faces, problem boundaries and interfaces to model incident and scattered fields. Every point source emits energy in all directions uniformly. Source strengths of these 360° radiation sources are obtained by satisfying interface and boundary conditions of the problem. In conventional DPSM modelling approach it is assumed that the shadow zone does not require any special consideration. 360° Radiation point sources should be capable of properly modelling shadow zones because all boundary and interface conditions are satisfied. In this paper it is investigated how good this assumption is by introducing the ‘shadow zone’ concept at the point source level and comparing the results generated by the conventional DPSM and by this modified approach where the conventional 360° radiation point sources are replaced by the Controlled Space Radiation (CSR) sources.     

Physical and chemical effects of acoustic cavitation in selected ultrasonic cleaning applications

Acoustic cavitation in a liquid medium generates several physical and chemical effects. The oscillation and collapse of cavitation bubbles, driven at low ultrasonic frequencies (e.g., 20 kHz), can generate strong shear forces, microjets, microstreaming and shockwaves. Such strong physical forces have been used in cleaning and flux improvement of ultrafiltration processes. These physical effects have also been shown to deactivate pathogens. The efficiency of deactivation of pathogens is not only dependent on ultrasonic experimental parameters, but also on the properties of the pathogens themselves. Bacteria with thick shell wall are found to be resistant to ultrasonic deactivation process. Some evidence does suggest that the chemical effects (radicals) of acoustic cavitation are also effective in deactivating pathogens. Another aspect of cleaning, namely, purification of water contaminated with organic and inorganic pollutants, has also been discussed in detail. Strong oxidising agents produced within acoustic cavitation bubbles could be used to degrade organic pollutants and convert toxic inorganic pollutants to less harmful substances. The effect of ultrasonic frequency and surface activity of solutes on the sonochemical degradation efficiency has also been discussed in this overview.     

Application of ZnO nanorods loaded on activated carbon for ultrasonic assisted dyes removal: Experimental design and derivative spectrophotometry method

A method based on application of ZnO nanorods loaded on activated carbon (ZnO-NRs-AC) for adsorption of Bromocresol Green (BCG) and Eosin Y (EY) accelerated by ultrasound was described. The present material was synthesized under ultrasound assisted wet-chemical method and subsequently was characterized by FE-SEM, TEM, BET and XRD analysis. The extent of contribution of conventional variables like pH (2.0–10.0), BCG concentration (4–20 mg L⁻¹), EY concentration (3–23 mg L⁻¹), adsorbent dosage (0.01–0.03 g), sonication time (1–5 min) and centrifuge time (2–6 min) as main and interaction part were investigated by central composite design under response surface methodology. Analysis of variance (ANOVA) was adapted to experimental data and guide the best operational conditions mass by set at 6.0, 9 mg L⁻¹, 10 mg L⁻¹, 0.02 g, 4 and 4 min for pH, BCG concentration, EY concentration, adsorbent dosage, sonication and centrifuge time, respectively. At these specified conditions dye adsorption efficiency was higher than 99.5%. The suitability and well prediction of optimum point was tested by conducting five experiments and respective results revel that RSD% was lower than 3% and high quality of fitting was confirmed by t-test. The experimental data were best fitted in Langmuir isotherm equation and the removal followed pseudo second order kinetics. The experimentally obtained maximum adsorption capacities were estimated as 57.80 and 61.73 mg g⁻¹ of ZnO-NRs-AC for BCG and EY respectively from binary dye solutions. The mechanism of removal was explained by boundary layer diffusion via intraparticle diffusion.     

基于虚拟源时间反转的经颅超声精确聚焦*

针对经颅超声难以精确聚焦的问题,本文研究了基于虚拟源的时间反转方法,建立颅骨二维数字模型,在聚焦目标处设置虚拟声源,利用时域有限差分法模拟超声时间反转过程,并考察基于虚拟源时间反转方法的聚焦效果。数值仿真结果表明,基于虚拟源的时间反转方法可以实现经颅超声的精确聚焦,聚焦强度和精度好于传统的相控聚焦;换能器中心频率和数量对聚焦效果的影响规律与相控聚焦时类似;该方法可以同时向多个焦点聚焦,并自适应调节各焦点处声压幅度。     

基于光纤光栅传感的金属薄板超声探测

搭建了光纤光栅检测超声应力波系统,并阐述其工作原理,以动态应变与光纤光栅中心波长漂移量间关系为基础,推导得出输出电压与板中应变成线性关系.采用超声信号发生器发射28kHz的脉冲信号激励超声振子,通过有机玻璃楔形块将激励传递至5052铝合金薄板产生超声应力波,并利用光纤光栅应变传感器对其进行探测.在板上开一98mm长裂缝,测得超声应力波中出现新的波包,通过计算损伤前后新增波包到来的时间差确定裂缝位置,所测结果与实际位置偏差为2.7mm.该实验表明光纤光栅可代替超声探头来实现对低频超声波的探测.     

A novel polyol method to synthesize colloidal silver nanoparticles by ultrasonic irradiation

A polyol synthesis of silver nanoparticles in the presence of ultrasonic irradiation was compared with other configurations (at ambient temperature, 120 °C, and 120 °C with injected solutions) in the absence of ultrasonic irradiation in order to obtain systematic results for morphology and size distribution. For applying ultrasonic irradiation, rather fine and uniform spherical silver particles (21 ± 3.7 nm) were obtained in a simple (at ambient temperature without mechanical stirring) and fast (within 4 min, 3.61 × 10⁻³ mol min⁻¹) manner than other cases (at ambient temperature (for 8 h, 0.03 × 10⁻³ mol min⁻¹): 86 ± 16.8 nm, 120 °C (for 12 min, 1.16 × 10⁻³ mol min⁻¹): 64 ± 14.9 nm, and 120 °C with injected solutions (during 12 min): 35 ± 6.8 nm; all other cases contained anisotropic shaped particles). Even though the temperature of polyol reaction reached only at 80 °C (<120 °C) in the presence of ultrasonic irradiation, a uniform mixing (i.e. enhanced collision between silver particle and surrounding components) by ultrasonic irradiation might induce a better formation kinetics and morphological uniformity.     

An efficient ultrasonic-assisted synthesis of ethyl-5-(aryl)-2-(2-alkokxy-2-oxoethylidene)-7-methyl-3-oxo-3, 5-dihydro-2H-thiazolo [3, 2-a] pyrimidine-6-carboxylate derivatives

Dihydropyrimidinone derivatives were prepared by tri-component reaction of ethyl aceto acetate, aldehydes and thiourea in the presence of modified montmorillonite nanostructure as a catalyst and used as key intermediates for the synthesis of ethyl-5-(aryl)-2-(2-alkokxy-2-oxoethylidene)-7-methyl-3-oxo-3,5-dihydro-2H-thiazolo[3,2-a]pyri midine-6-carboxylate derivatives with use of diethyl and dimethyl acetylene dicarboxylate by two methods: (a) in methanol as a solvent under ultrasonic irradiation at ambient temperature (b) in methanol as a solvent at ambient temperature (conventional magnetic stirring). Ultrasound-assisted synthesis provides excellent yields in short reaction times (15–25 min) at room temperature.     

Fast Electrochemical Characterization of Historical Glasses Using Carbon Screen‐Printed Electrodes and Ultrasonic Assisted Sampling

A new method for lead oxide (PbO) analysis in glasses, using a carbon screen printed electrode (SPE) is proposed. A suspension of the powdered glass sample in nitric acid is prepared using an ultrasonic probe, 100 µL of slurry are deposited on the SPE and the voltammetric measurement is carried out. Structural information of PbO in the glass matrix is obtained by CV. Lead quantification is performed by DPV. In the best conditions a LOD of 2.30 wt% of PbO was obtained. The method has been applied with good results in the analysis of historical glasses samples.