Biomimetic piezoelectric quartz sensor for caffeine based on a molecularly imprinted polymer

A piezoelectric quartz sensor coated with molecularly imprinted polymer (MIP) for caffeine was developed. The MIP was prepared by co-polymerizing methacrylic acid (MAA) and ethylene glycol dimethacrylate (EDMA) in the presence of azobis(isobutyronitrile) as initiator, caffeine as template molecule, and chloroform as solvent. The MIP suspension in polyvinyl chloride/tetrahydrofuran (6:2:1 w/w/v) solution was spin coated onto the surface of the electrode of a 10 MHz AT-cut quartz crystal. The sensor exhibited a linear relationship between the frequency shift and caffeine concentration in the range of 1×10^–7 mg mL^–1 up to 1x10^–3 mg mL^–1 [correlation coefficient (r)=0.9935] in a stopped flow measurement mode. It has a sensitivity of about 24 Hz/ln(concentration, mg mL^–1). A steady-state response was achieved in less than 10 min. The performance characteristic of the sensor shows a promising and inexpensive alternative method of detecting caffeine. Surface studies were carried out for the reagent phase of the sensor using SEM, AFM, and XPS analysis in order to elucidate the imprinting of the caffeine molecule. The SEM micrograph, AFM image, and XPS spectra confirmed the removal of caffeine by Soxhlet extraction in the imprinting process and the rebinding of caffeine to the MIP sensing layer during measurement.     

Utilization of a spiropyran derivative in a polymeric film optode for selective fluorescent sensing of zinc ion

Spiropyrans are the most studied families of func- tional materials due to their reversible structural con- version in response to external optical, chemical, and thermal stimulation[1]. Irradiation with ultraviolet light causes formation of an extended π-conjugation open form (merocyanine form) by heterolytic cleavage of the C (spiro)-O bond, which generates an intense ab- sorption in the visible region. Under the irradiating of visible light, the opened form will come back to the closed spi…     

Use of a Carbon Paste Electrode Modified with Spinel‐Type Manganese Oxide as a Potentiometric Sensor for Lithium Ions in Flow Injection Analysis

A potentiometric sensor constructed from a mixture of 25% (m/m) spinel‐type manganese oxide (lambda‐MnO₂), 50% (m/m) graphite powder and 25% (m/m) mineral oil is used for the determination of lithium ions in a flow injection analysis system. Experimental parameters, such as pH of the carrier solution, flow rate, injection sample volume, and selectivity for Li⁺ against other alkali and alkaline‐earth ions and the response time of this sensor were investigated. The sensor response to lithium ions was linear in the concentration range 8.6×10^?5–1.0×10^?2 mol L^?1 with a slope 78.9±0.3 mV dec^?1 over a wide pH range 7–10 (Tris buffer), without interference of other alkali and alkaline‐earth metals. For a flow rate of 5.0 mL min^?1 and a injection sample volume of 408.6 μL, the relative standard deviation for repeated injections of a 5.0×10^?4 mol L^?1 lithium ions was 0.3%.     

Photoinitiators for UV and visible curing of coatings: Mechanisms and properties

The radiation curing industry is one of the most rapidly developing fields in the entire coatings industry. The low toxicity, cheapness, speed, control and ease of formulation and operation are some of the main advantages of this growing technology. UV and/or visible light radiation is used to induce photochemical polymerization or crosslinking of a monomer, oligomer or prepolymer formulation containing a certain type of unsaturation, such as an acrylic group, and an appropriate initiator. The latter is used to absorb the light energy and transform it into active species, such as radicals or ions, capable of inducing such reactions. Applications extend to general coatings for paper, board, wood, tapes, compact discs and holograms, inks, photoresists for imaging processes and adhesives for welding and sealing in electronic circuit boards. The photoinitiator is the key to the control of these processes and, in recent years, has seen many new developments. These include the need for water-soluble, co-reactive and polymeric structures with low migration rates, as well as cheaper UV/ visible sensitizers with enhanced speed. New and effective cationic systems are also on the scene and, although expensive, are attracting significant academic and commercial interest.     

Thermal and mechanical properties of UV irradiated collagen/chitosan thin films

The thermal and mechanical properties of collagen/chitosan blends before and after UV irradiation have been investigated using thermal analysis and mechanical (Instron) techniques. Comparisons were made with the thermal and mechanical properties of both collagen and chitosan films. Air-dried collagen, chitosan and collagen/chitosan films were exposed to UV irradiation (wavelength 254 nm) for different time intervals. Thermal properties of collagen/chitosan blends depend on the composition of the blend and are not significantly altered by UV irradiation.Mechanical properties such as ultimate tensile strength and ultimate percentage of elongation were much better for collagen films than for collagen/chitosan films. The results have shown that the mechanical properties of the blends were greatly affected by the duration of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the blend. Increasing UV irradiation leads to an increase in Young's modulus of the collagen/chitosan blend.     

A Photophysical Study of Terphenyl Core Oligosulfonimide Dendrimers Exhibiting High Steady‐State Anisotropy

The photophysical properties of three dendrimers containing a p‐terphenyl core with appended sulfonimide branches of different size and n‐octyl chains have been investigated in dichloromethane solution. In the dendrimer absorption spectra contributions from both the branches and the core are clearly identified. The fluorescence spectra show only the characteristic fluorescence of the terphenyl unit. Energy transfer from the appended chromophoric groups to the core does not occur. In the dendrimers, the terphenyl core exhibits a very high fluorescence quantum yield (ca. 0.75) and a short emission lifetime (0.8 ns). These properties allowed investigations of the fluorescence depolarization caused by rotation of the dendrimers. The dendrimers show a very high steady‐state anisotropy in dichloromethane solution at room temperature (0.24 for the largest one), compared to that of the parent terphenyl under the same experimental conditions (<0.01) and in rigid matrix (0.33). Both the n‐octyl chains and the sulfonimide branches play important roles to slow down the molecular rotation.     

Synthesis, structures and spectroelectrochemistry of methyl-substituted bis(η-indenyl)iron(II) complexes

Several new methyl-substituted indenyl ferrocenes were prepared by metathesis reactions of the indenide (generated from the appropriate indene with BuLi) with ferrous chloride. The indenides used to prepare new ferrocenes were: 2-methyl-, 1,2-dimethyl-, 4,7-dimethyl-, 1,4,7-trimethyl-, and 1,3,4,7-tetramethyl-indenide. These indenyl ferrocenes, along with those prepared from indenide, 1-methylindenide, and 1,3-dimethylindenide, were then characterized by ¹H and ¹³C NMR, UV/visible spectroscopy, cyclic voltammetry and mass spectrometry. The cyclic voltammetry showed an additive relationship between oxidation potential and the number of methyl groups which is also position-dependent, whereas the UV/visible spectra showed two absorptions essentially unaffected by methyl substitution. Additionally, bis(2-methylindenyl)iron(II) and bis(4,7-dimethylindenyl)iron(II) were characterized by X-ray crystallography.     

Nafion-PAN optical chemical sensor: optimization by FIA

A copper-sensitive optical chemical sensor (optrode) is described. The optrode is based on a Nafion membrane and an immobilized organic ligand coupled with a flow injection (FI) system. The FI system includes a flow-through removable measuring cell and a simple spectrophotometer. Owing to the miniature size of the system and the efficient use of optical fibers, this optrode is well suited for monitoring environmental water samples. The success of the described optrode system depends on the effectiveness of the FI reagent delivery system. Optimum contact time with the membrane (as determined by the reagent flow rates) and the injected sample volume are critical. Environmental water samples were analyzed for copper content using the optimized optrode system. To validate the optrode's performance, the same water samples were analyzed using the atomic absorption spectrophotometer.     

UV stabilizers bonded to transition metals: Synthesis and X-ray structure of 2-(2′-hydroxyphenyl)benzotriazole-oxovanadium(IV) and -dioxomolybdenum(VI) complexes

The UV-stabilizer 2-(2′-hydroxy-5′-methylphenyl)benzotriazole (Tinuvin P, LH) has been used as a monoanionic bidentate ligand for complexing oxocations. Displacement of acacH from [VO(acac)₂] and [MoO₂(acac)₂] gave [*VO(acac)₂*(μ-L)] (2) and [cis-O₂Mo(acac)L] (3) respectively, as crystalline compounds. Their structure has been determined by an X-ray analysis showing the structural changes occurring upon coordination. The UV spectrum of Tinuvin P is significantly affected by complexation.     

New Host Molecules with Imidazoliums as Functional Arms:Syntheses and Anion Recognition

The bridged tri-imidazoliums 3.3X^--5.3X^-(X^-=PF6^-,Br^-,I^-)and bis-imidazoliums 6.2PF6^- were synthesized by N-quaternization of imidazole derivative 1 in acetonitrile under reflux.UV spectroscopic titration experiments showed that the halide salts and hexafluorophosphate salts of these imidazoliums exhibited good recognition toward anions in water and in acetonitrile,respectively.