不同方法制备的CO2-3替换磷灰石固溶体晶体化学的FTIR研究

采用不同方法制备了CO2-3替换的磷灰石固溶体,利用FTIR结合XRD对其进行了晶体化学研究,结果表明均相沉淀法制备的碳羟磷灰石(CHAP)属B型替换且替换方式是[CO3·OH]四面体替换[PO4]四面体;固相离子交换法制备的CHAP属A型替换且替换方式是[CO3]三角形配位体替换通道位置的OH-;固相反应法制备的碳氟磷灰石(CFAP)属B型替换,其替换方式是[CO3·F]四面体替换[PO4]四面体;sol-gel法制备的CHAP属AB混合型替换,其Ψ3分裂为Ψ3-1,Ψ3F,Ψ3-4.高斯函数法拟合表明Ψ3F峰是A型替换的Ψ3-2与B型替换的Ψ3-3的叠合.当WCO2-3＜3.34%时,随CO2-3含量增加,A型替换量增大,且当WCO2-3=3.34%时达最大值,当3.34%＜WCO2-3＜7.52%时,随CO2-3含量增加,B型替换量增大,且当WCO2-3= 7.52%时亦到饱和.     

无催化纳米氧化锌的制备及其光学性质研究

本文采用无催化剂直接蒸发高纯Zn粉,在800℃氧气氛条件下,在Si(111)衬底上生长得到以四角状为主的纳米ZnO(T-ZnO)。T-ZnO纳米线每个角约互成110°,长度约为1.5μm,直径100nm左右;Raman分析表明E2(H)普遍存在于各形态的ZnO;光致发光光谱表明,T-ZnO纳米线的光致发光除了与材料性质有关,还与杂质缺陷有关,蓝绿光带是ZnO的缺陷产生的。     

Holographic interferometry as electrochemical emission spectroscopy of a carbon steel in 5–20 ppm TROS C-70 inhibited seawater

In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the number of the fringe evolutions during the corrosion test of a carbon steel in blank seawater and seawater with different concentrations of a corrosion inhibitor. In other words, the anodic dissolution behaviors (corrosion) of the carbon steel were determined simultaneously by holographic interferometry, as an electromagnetic method, and by the electrochemical impedance (EI) spectroscopy, as an electronic method. So, the abrupt rate change of the number of the fringe evolutions during corrosion tests, EI spectroscopy, of the carbon steel is called electrochemical emission spectroscopy. The corrosion process of the steel samples was carried out in blank seawater and seawater with different concentrations, 5–20 ppm, of TROS C-70 corrosion inhibitor using the EI spectroscopy method, at room temperature. The electrochemical-emission spectra of the carbon steel in different solutions represent a detailed picture of the rate change of the anodic dissolution of the steel throughout the corrosion processes. Furthermore, the optical interferometry data of the carbon steel were compared to the data, which was obtained from the EI. spectroscopy. Consequently, holographic interferometry is found very useful for monitoring the anodic dissolution behaviors of metals, in which the number of the fringe evolutions of the steel samples can be determined in situ.     

Structural and lithium intercalation studies of Mn(0.5−x)CaxTi2(PO4)3 phases (0≤x≤0.50)

Materials from the Mn_(0.5−x)Ca_xTi₂(PO₄)₃ (0≤x≤0.50) solid solution were obtained by solid-state reaction in air at 1000 °C. Selected compositions were investigated by powder X-ray diffraction analysis, ³¹P nuclear magnetic resonance (NMR) spectroscopy and electrochemical lithium intercalation. The structure of all samples determined by Rietveld analysis is of the Nasicon type with the R space group. Mn²⁺/Ca²⁺ ions occupy only the M1 sites in the Ti₂(PO₄)₃ framework. The divalent cations are ordered in one of two M1 sites, except for the Mn_0.50Ti₂(PO₄)₃ phase, where a small departure from the ideal order is observed by XRD and ³¹P MAS NMR. The electrochemical behaviour of Mn_0.50Ti₂(PO₄)₃ and Mn_(0.5−x)Ca_xTi₂(PO₄)₃ phases was characterised in Li cells. Two Li ions can be inserted without altering the Ti₂(PO₄)₃ framework. In the 0≤y≤2 range, the OCV curves of Li//Li_yMn_0.50Ti₂(PO₄)₃ cells show two main potential plateaus at 2.90 and 2.50–2.30 V. Comparison between the OCV curves of Li//Li_(1+y)Ti₂(PO₄)₃ and Li//Li_yMn_0.50Ti₂(PO₄)₃ shows that the intercalation occurs first in the unoccupied M1 site of Mn_0.50Ti₂(PO₄)₃ at 2.90 V and then, for compositions y>0.50, at the M2 site (2.50–2.30 V voltage range). The effect of calcium substitution in Mn_0.50Ti₂(PO₄)₃ on the lithium intercalation is also discussed from a structural and kinetic viewpoint. In all systems, the lithium intercalation is associated with a redistribution of the divalent cation over all M1 sites. In the case of Mn_0.50Ti₂(PO₄)₃, the stability of Mn²⁺ either in an octahedral or tetrahedral environment facilitates cationic migration.     

CO-laser photoacoustic detection of phosgene (COCl2)

Detection of COCl₂, a highly toxic gas in chemical industry, using laser photoacoustic spectroscopy is presented. The spectrophone system used has a broad band LN₂ cooled CW CO laser as a source of radiation, which operates from 4.8–8.4 um in the mid-infrared. Using an extracavity open longitudinal resonant cell, absorption signals to about 30 CO laser lines in the 5.45 um region could be observed. detection sensitivity has been estimated to be ppb order.This work has been supported by the NSFC     

Effects of UV photon irradiation on SiOx (0 < x < 2) structural properties

Thin films of a-SiO_x (0 < x < 2) were prepared by reactive r.f. magnetron sputtering from a polycrystalline-silicon target in an Ar/O₂ gas mixture. The oxygen partial pressure in the deposition chamber was varied so as to obtain films with different values of x. The plasma was monitored, during depositions, by optical emission spectroscopy (OES) system. Energy dispersive X-ray (EDX) measurements and infra-red (IR) spectroscopy were used to study the compositional and structural properties of the deposited layers.Structural modifications of SiO_x thin films have been induced by UV photons’ bombardment (wavelength of 248 nm) using a pulsed laser. IR spectroscopy and X-ray photoemission spectroscopy (XPS) were used to investigate the structural changes as a function of x value and incident energy. SiO_x phase separation by spinodal decomposition was revealed. The IR peak position shifted towards high wavenumber values when the laser energy is increased. Values corresponding to the SiO₂ material (only Si⁴⁺) have been found for laser irradiated samples, independently on the original x value. The phase separation process has a threshold energy that is in agreement with theoretical values calculated for the dissociation energy of the investigated material.For high values of the laser energy, crystalline silicon embedded in oxygen-rich silicon oxide was revealed by Raman spectroscopy.     

Amorphous Fe–Mg alloy thin films: magnetic properties and atomic vibrational dynamics

Amorphous (a-) Fe _x Mg_1?x alloys are interesting materials for the investigation of non-Debye-like low-energy vibrational excitations. We have prepared a-Fe _x Mg_1?x alloy thin films (0.3 ≤ × ≤0.7) by vapour quenching. The amorphous state was confirmed by conversion electron Mössbauer spectroscopy between 4.2–300 K, and the x- and temperature-dependence of the isomer shift and hyperfine magnetic field was measured. For x= 0.6 and 0.7, magnetic ordering occurs below ~150 K. The atomic vibrational density of states, g(E), was determined by nuclear resonant inelastic scattering, providing clear evidence for the non-Debye-like low-energy vibrational excitations.     

Modification of magnetic anisotropy in metallic glasses using high-energy ion beam irradiation

Heavy ion irradiation in the electronic stopping power region induces macroscopic dimensional change in metallic glasses and introduces magnetic anisotropy in some magnetic materials. The present work is on the irradiation study of ferromagnetic metallic glasses, where both dimensional change and modification of magnetic anisotropy are expected. Magnetic anisotropy was measured using Mössbauer spectroscopy of virgin and irradiated Fe₄₀Ni₄₀B₂₀ and Fe₄₀Ni₃₈Mo₄B₁₈ metallic glass ribbons. 90 MeV ¹²⁷I beam was used for the irradiations. Irradiation doses were 5×10¹³ and 7.5×10¹³ ions/cm². The relative intensity ratios D ₂₃ of the second and third lines of the Mössbauer spectra were measured to determine the magnetic anisotropy. The virgin samples of both the materials display in-plane magnetic anisotropy, i.e., the spins are oriented parallel to the ribbon plane. Irradiation is found to cause reduction in magnetic anisotropy. Near-complete randomization of magnetic moments is observed at high irradiation doses. Correlation is found between the residual stresses introduced by ion irradiation and the change in magnetic anisotropy.     

Synthesis of functional polymers—Vinylidene fluoride based fluorinated copolymers and terpolymers bearing bromoaromatic side‐group

The radical co‐ and terpolymerization of 4‐[(α,β,β‐trifluorovinyl)oxy]bromo benzene (TFVOBB) with 1,1‐difluoroethylene (or vinylidene fluoride, VDF, or VF₂), hexafluoropropene (HFP), perfluoromethyl vinyl ether (PMVE), and chlorotrifluroroethylene (CTFE) is presented. Although TFVOBB could be thermocyclodimerized, it could not homopolymerize under radical initiation. TFVOBB could be copolymerized in solution under a radical initiator with VDF or CTFE comonomers, while its copolymerization with HFP or PMVE were unsuccessful. The terpolymerization of TFVOBB with VDF and HFP, or VDF and PMVE, or VDF and CTFE also led to original fluorinated terpolymers bearing bromoaromatic side‐groups. The conditions of co‐ and terpolymerization were optimized in terms of the nature of the radical initiators, and of the nature of solvents (fluorinated or nonhalogenated). Various monomer concentrations in the co‐ and terpolymers were assessed by ¹⁹F and ¹H‐NMR spectroscopy. The thermal and physico chemical properties were also studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5077–5097, 2004