DMF体系中Cu2O球晶的制备及形貌分析

以N,N-二甲基甲酰胺(DMF)为溶剂,通过改变铜源和表面活性剂,调控反应参数,溶剂热条件下制备了三维十字形、空心及实心的Cu₂O球晶。利用XRD、SEM等表征手段,分析探讨了工艺条件变化对Cu₂O球晶形貌的影响。研究表明,随着DMF浓度的增大,体系的还原能力增强,Cu⁺增多,溶液的过饱和度增大,Cu₂O晶体集合体形态由晶体结构控制的各向异性与对称性的球晶逐渐向各向同性球晶演变。十二烷基硫酸钠(SDS)、十六烷基三甲基溴化铵(CTAB)、聚乙烯吡咯烷酮(PVP)等表面活性剂有助于降低溶液的过饱和度,增加结晶质的表面扩散能力,有利于规则形态Cu₂O晶粒的形成。反应体系中,Cu(Ac)₂·H₂O水解生成的羧基与DMF中的甲酰基在高温下发生脱羧反应产生CO₂气体以及SDS发泡作用产生的气体是形成空心Cu₂O球晶的重要原因。     

Cu3N薄膜及其研究现状

Cu3N薄膜是近10年来研究的热点材料之一.Cu3N是立方反ReO3结构,理想立方反ReO3结构的一个晶胞中Cu原子占据立方边的中心位置而N原子占据立方晶胞的八个顶点,此结构的体心位置有一较大间隙,Cu原子以及其他原子如Pd、碱金属原子等很有可能进入此位置导致Cu3N的电学性能、光学性能等发生很大的变化,这使得该材料具有很大的潜在应用价值.Cu3N的晶格常数为0.3815nm,密度5.84g/cm3,分子量204.63,颜色呈黑绿色或红褐色,空间点群Pm3m.Cu3N薄膜在室温下相当稳定并且热分解温度较低(300℃左右),热分解前后薄膜的光学反射率有较大差别,这可使Cu3N薄膜用作一次性光记录材料.此外,Cu3N薄膜还可用作在Si片上沉积金属Cu线的缓冲层、低磁阻隧道结的阻挡层、自组装材料的模板等.     

Laser cladding of copper with molybdenum for wear resistance enhancement in electrical contacts

Laser cladding of Mo on Cu has been attempted with the aim of enhancing the wear resistance and hence increasing the service life of electrical contacts made of Cu. In order to overcome the difficulties arising from the large difference in thermal properties and the low mutual solubility between Cu and Mo, Ni was introduced as an intermediate layer between Mo and Cu. The Ni and Mo layers were laser clad one after the other to form a sandwich layer of Mo/Ni/Cu. Excellent bonding between the clad layer and the Cu substrate was ensured by strong metallurgical bonding. The hardness of the surface of the clad layer is seven times higher than that of the Cu substrate. Pin-on-disc wear tests consistently showed that the abrasive wear resistance of the clad layer was also improved by a factor of seven as compared with untreated Cu substrate. The specific electrical contact resistance of the clad surface was about 5.6 × 10⁻⁷ Ω cm².     

（Ti,Al）N薄膜光学性能的研究

研究了（Ｔｉ，Ａｌ）薄膜的光学特性，对其反射和透射光谱作了仔细分析。运用Ｈａｄｌｅｙ方程，算出一定成分（Ｔｉ，Ａｌ）Ｎ膜的折射率ｎ，消光系数ｋ随波长的变化关系。又根据透射曲线，计算出了（Ｔｉ，Ａｌ）Ｎ膜的光隙能。     

The Determination of Trace Elements by Flame Atomic Absorption Spectrometry: Effect of the Composition of Standard Solution Matrices

Abstract

The effect of using solution matrices in calibration standards different from those employed for the extraction steps in the determination of Cd, Cr, Cu, Ni and Zn were tested. Cu and Zn are little affected by matrix effects but, if the extractant is ammonium acetate, the use of other matrices may result in too high Cd, Cr and Ni values.     

Study of Optically Stimulated Luminescence of LiF:Mg,Ti for beta and gamma dosimetry

Modern advances in radiation medicine – radiodiagnosis, radiotherapy and interventional radiography – each present dosimetry challenges for the medical physicist that did not exist previously. In all of these areas a constant balance has to be made between the treatment necessary to destroy the tumor and the unnecessary exposure of healthy tissue. Innovative applications of OSL dosimetry are now appearing in each of these areas to help the medical physicist and oncologist design the most effective, and least deleterious, treatment for their patients. High sensitivity, precise delivery of light, fast readout times, simpler readers and easier automation are the main advantages of OSL in comparison with TLD.This work aimed to study the application of OSL technique using lithium fluoride dosimeters doped with magnesium and titanium (LiF:Mg,Ti) for application in beta and gamma dosimetry.     

XRF测定铅锌矿选矿流程中铅,锌,铜

本文叙述一个ＸＲＦ粉末法测定铅锌矿选矿流程中铅，锌，铜的方法，选用精，中矿和原，尾矿两个标准系列。ＲｈＫａ康普顿散射线作内标克服质量吸收系数变化带来的影响，用经验系数法校正基体效应，与化学分析方法相比，本法县有测定组分含量范围广，简便，快速，准确和成本低等特点，配合选矿试验大大加快造矿周期，提高工效数倍。     

低功率泵浦Ti：Al2O3自锁模激光器

本文报道了低功率泵浦的Ｔｉ：Ａｌ２Ｏ３激光器实现了稳定的自锁模运转，锁模脉冲宽度为１８０ｆｓ。分析了激光器的结构及工作特性。     

BaHf0.5Ti0.5O3电子结构与光学性质的第一性原理研究

基于密度泛函理论体系下的广义梯度近似（GGA）,利用第一性原理方法研究了BaHf0.5Ti0.5O3的电子结构和光学性质．计算结果表明,BaHf0.5Ti0.5O3是一种间隙的半导体材料,其导带底主要由Ba、Hf和Ti的d态电子构成,价带顶则主要由O的p态、Hf 和Ti的d态电子构成;理论计算的介电函数最高峰的峰位与实验结果吻合较好,相对误差小于4%;吸收系数最大峰值为2.43×105cm-1,且吸收主要集中在低能区,静态折射率为2.01,能量损失峰出现在13.24eV处．研究结果为BaHf0.5Ti0.5O3光电材料设计与应用提供了理论依据．